summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-04-30powerpc, 83xx: add kmsupx5 board supportHeiko Schocher
The Keymile SUPx5 board series is based on a PBEC8321 but contains an additional PBUS FPGA (LPXF) on local bus CS2. Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com>
2011-04-30keymile, 8321 boards: move common definitions to km8321-common.hThomas Reufer
First step for a cleanup of all header files for km8321 boards. Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Heiko Schocher <hs@denx.de>
2011-04-30ppc: add support for ppc based board mgcoge2neHeiko Schocher
The mgcoge2 board from keymile deploys two different processors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30arm: add support of Kirkwood based board SUEN8Heiko Schocher
The Kirwood based SUEN8 board from Keymile is at this stage the same than the suen3 board. This patch adds the board support for the suen8. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30arm: add support for kirkwood based mgcoge2un boardHeiko Schocher
This board is similar to keymile suen3. Signed-off-by: Clive Stubbings <clive.stubbings@xentech.co.uk> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30mpc832x: add support for mpc8321 based tuda1 boardHeiko Schocher
This board is similar to suvd3 board. So most initialisation topics are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the application specific chip selects differ. Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30mpc832x: add support for mpc8321 based tuxa1 boardHeiko Schocher
This board is similar to suvd3 board. So most initialisation topics are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the application specific chip selects differ. Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher
- serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30arm, ppc: rework environment variables for keymile boardsHolger Brunck
This patch reworks all headerfiles for keymile boards. Furthermore the environment variables are refactored. Changes: - introduce km-powerpc.h file and extract ppc specific parts to it - move ARM specific options and vaiables to km_arm.h - sort the environment variables to logical groups - enhance the description of the environment variables - remove KM specific HW key and board id from kernel command line Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30ppc, arm: adapt keymile headerHolger Brunck
- adapt copyright string - change bootdelay to 2 seconds - set max number of command args to 32 - set I/O buffer size to 512 Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30keymile: Fix Coding style issues for keymile boards.Heiko Schocher
- use I/O accessors -> For accessing the FPGA therefore a struct km_bec_fpga is introduced. - no longer externs needed - to defines, that only select functions, don;t assign a numeric value - Codingstyle changes to prevent checkpatch errors/warnings Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30arm, keymile: rename MACH_SUEN3 to MACH_KM_KIRKWOODHolger Brunck
The MACH_TYPE SUEN3 is now to specific for keymile boards, because other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed to MACH_KM_KIRKWOOD. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30powerpc, mpc83xx: add missing functions to include/common.hHeiko Schocher
add following functions to common.h, to prevent extern declarations: void disable_addr_trans(void); void enable_addr_trans(void); void ddr_enable_ecc(unsigned int dram_size); Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-29Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk
2011-04-29fsl-ddr: Fix mixed-case macro namesKyle Moffett
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29powerpc/85xx: Bump up the CONFIG_SYS_BOOTM_LEN to 64M on FSL 85xx boardsKumar Gala
CONFIG_SYS_BOOTMAPSZ has been 64M on these boards for some time so we should also allow the kernel image to be up to 64M decompressed. This also matches what we pass to the OS based on the ePAPR specification. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29powerpc/85xx: Enable eSPI support on P1022DSJiang Yutang
Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29powerpc/85xx: Enable eSPI support for p1_p2_rdbPriyanka Jain
Also added support to save env to spi flash in case of SPIBOOT. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29powerpc/85xx: Enable eSPI controller & SPI boot support on P2020DSJerry Huang
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29powerpc: eSPI and eSPI controller supportMingkai Hu
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29tsec: Fix MDIO on devices with eTSEC2Andy Fleming
The tsec driver was defining the default MDIO address as the TSEC_BASE + 0x520, but on eTSEC2 controllers, the first TSEC's registers are separated from the MDIO registers. Use the existing MDIO_BASE_ADDR, instead. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29mmc: coding style fix and tabify of mmc.hThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2011-04-29fsl_esdhc: Fix multi-block read restriction on i.MX53 eSDHCv2Jason Liu
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need to be set to ABORT, otherwise, next read command will hang. This is a software Software Restrictions in i.MX53 reference manual: 29.7.8 Multi-block Read For pre-defined multi-block read operation, that is,the number of blocks to read has been defined by previous CMD23 for MMC, or pre-defined number of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without abort command at card side, an abort command, either automatic or manual CMD12/CMD52, is still required by ESDHC after the pre-defined number of blocks are done, to drive the internal state machine to idle mode. In this case, the card may not respond to this extra abort command and ESDHC will get Response Timeout. It is recommended to manually send an abort command with RSPTYP[1:0] both bits cleared. Signed-off-by: Jason Liu <jason.hui@linaro.org>
2011-04-29MMC: omap_hsmmc.c: disable multiblock rw on old rev omap34xx siliconJohn Rigby
Signed-off-by: John Rigby <john.rigby@linaro.org>
2011-04-29MMC: make b_max unconditionalJohn Rigby
Make existing field b_max field in struct mmc unconditional and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread and mmc_bwrite. Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register if it has not been initialized by the hw driver. Initialize b_max to 0 in all callers to mmc_register. Signed-off-by: John Rigby <john.rigby@linaro.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-29mmc_spi: add mmc_init callThomas Chou
As Andy Fleming suggested, we can call mmc_init() in mmc_spi command. So that we don't need to run mmcinfo command next. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2011-04-29ARMV7: Vexpress: Add MMC supportMatt Waddel
Added the board specific definitions to use the MMCI device. Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2011-04-29MMC: Add support for PL180 ARM mmc deviceMatt Waddel
Add support for the ARM PrimeCell MultiMedia Interface - PL180. Ported from original device driver written by ST-Ericsson. Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2011-04-28powerpc/85xx: Change timebase divisor to be defined per processorKumar Gala
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because different SoCs have different divisor amounts. All the PQ3 parts are /8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001Timur Tabi
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1 are swapped. Erratum SERDES-A001 says that if bank two is kept disabled and after bank three is enabled, then the PLL for bank three won't lock properly. The work-around is to enable and then disable bank two after bank three is enabled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Extend SERDES9 erratum work-around to SGMII, SRIO, and AURORATimur Tabi
Part of the SERDES9 erratum work-around is to set some bits in the SerDes TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The current code does this only for XAUI, so extend it to the other protocols. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Display SERDES 8 erratum warning if banks are not disabledTimur Tabi
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two and three to be disabled (powered down) in the RCW. Display a warning message if this is not the case. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005Timur Tabi
SerDes PLL bandwidth default setting is incorrect when no lanes are configured as PCI Express. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/fsl: add 'pixis_reset dump' commandTimur Tabi
Add the 'pixis_reset dump' command, which displays the contents of the PIXIS registers. This command is only available if DEBUG is defined. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28powerpc/86xx: remove empty board_early_init_f()Timur Tabi
Remove an empty board_early_init_f() from the MPC8641HPCN board. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
2011-04-28Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
2011-04-28powerpc: use 'video-mode' environment variable to configure DIUTimur Tabi
Use the 'video-mode' environment variable (for Freescale chips that have a DIU display controller) to designate the full video configuration. Previously, the DIU driver used the 'monitor' variable, and it was used only to determine the output video port. The old definition of the "monitor" environment variable only determines which video port to use for output. This variable was set to a number (0, 1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The resolution was hard-coded into board-specific code. The Linux command-line arguments needed to be hard-coded to the proper video definition string. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-04-28video: parse the video-mode environment variableTimur Tabi
Add function video_get_video_mode(), which parses the "video-mode" environment variable and returns each of its components. The format matches the video= command-line option used for Linux: video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string> <driver> The video driver, ignored by U-Boot <xres> The X resolution (in pixels) to use. <yres> The Y resolution (in pixels) to use. <depth> The color depth (in bits) to use. <freq> The frequency (in Hz) to use. <options> A comma-separated list of device-specific options Signed-off-by: Timur Tabi <timur@freescale.com>
2011-04-28cfb_console: fix RLE bitmap drawing codeAnatolij Gustschin
There seems to be tools producing incorrect 'end of bitmap data' markers '0100' in a RLE bitmap. Drawing such bitmaps can result in overwriting memory above the frame buffer. E.g. on MPC5121e based boards this memory can contain U-Boot environment. We may not rely on the correct end of bitmap data marker 0001 only, but also have to check whether we are going to draw a valid frame buffer scan line. The patch provides a fix by maintaining a pixel counter which is incremented by the amount of pixels we are going to draw. If the counter exceeds frame buffer pixels limit we stop the drawing with the error message. Reported-by: Michael Weiss <michael.weiss@ifm.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Tested-by: Anatolij Gustschin <agust@denx.de>
2011-04-28Add CONFIG_OF_LIBFDT to more boards.Grant Likely
The following boards gain device tree support with this patch: ca9x4_ct_vxp - Versatile Express i.mx5 boards: efikamx mx51evk mx53evk OMAP boards: devkit8000 igep0020 igep0030 omap3_overo omap3_pandora omap4_sdp3430 omap3_zoom1 omap3_zoom2 omap4_panda omap4_sdp4430 Tegra boards: Harmony Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-28i2c, soft_i2c: deblock bus if switching to another i2c busHeiko Schocher
Deblock i2c bus when switching to another i2c bus, if using i2c_set_bus_num(). Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-28i2c: add i2c deblock sequence before and after every mux configStefan Bigler
To make sure that the mux can be configured a deblocking sequence is done before the mux configuration. After the mux switch the new leaf of, the i2c tree must be again deblocked. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-28arm: a320: fix compile error caused by commit 00d10ebPo-Yu Chuang
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-04-27powerpc/85xx: Don't set FT_FSL_PCI_SETUP if CONFIG_PCI is not setMatthew McClintock
A lot of boards set FT_FSL_PCI_SETUP directly in their board code and don't check to see if CONFIG_PCI is actually defined. This will cause the board compilation to fail if CONFIG_PCI is not defined. The p1022ds board is one such example. Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP around CONFIG_PCI so we can remove CONFIG_PCI and boards will still build properly. Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc/85xx: handle both "secX.Y" and "sec-vX.Y" propertiesKim Phillips
versioned SEC properties changed names during development, so for now search and update LIODNs for both "secX.Y" and "sec-vX.Y" based properties. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc/85xx: Enable ESDHC111 erratum on P2040/P3041/P5010/P5020 SoCsLei Xu
The workaround for ESDHC111 should also be applied on P2040/P3041/P5010/P5020 SoCs. Signed-off-by: Lei Xu <B33228@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020Roy Zang
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we need to enable for them to function. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27powerpc: Add P3041DS/P5020DS board support (uses corenet_ds code)Kumar Gala
The P3041DS & P5020DS boards are almost identical (except for the processor in them). Additionally they are based on the P4080DS board design so we use the some board code for all 3 boards. Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock configuration. Additionally, the P3041DS/P5020DS support NAND. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27p4080/serdes: Implement the XAUI workaround for SERDES9 erratumEmil Medve
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2024-12-28 16:36:33 +0000