summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-03-30configs: lx2160a: Enable GIC_V3_ITS configWasim Khan
Enable GIC_V3_ITS config to program GIC LPI configuration table. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: fsl: lx2160a: Program GIC LPI configuration tableWasim Khan
Program GIC LPI configuration table: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: Manish Tomar <manish.tomar@nxp.com> Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: lx2160a: Correct board fixup for PCIe nodesVikas Singh
Update "board_fix_fdt" with correct counter value "i". This will fix the issue while fetching the "reg_names" resource from fdt after fixup. Signed-off-by: Vikas Singh <vikas.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30ls1021a: Set CONFIG_SYS_BOOTMAPSZ to the memory for relocationAlison Wang
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available to safely contain a kernel, device tree and initrd for relocation. The way to set fdt_high as 0xffffffff to disable device tree relocation is removed. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30ARM: dts: rmobile: Enable IIC3 on V2H BlancheMarek Vasut
Enable IIC3 to permit access to the PMIC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-30ARM: dts: rmobile: Add IIC3 node on Gen2 R8A7792 V2HMarek Vasut
Add IIC3 node from mainline Linux DT. This will be further updated in subsequent DT sync, however adding this node for now is sufficient and minimal change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-30clk: renesas: Switch to fdtdec_get_addr_size_auto_noparent() on Gen2Marek Vasut
The fdtdec_get_addr() does not take into account values set in #address-cells and #size-cells , but assumes them to be 1 for 32bit systems and 2 for 64bit systems. This is true for most DTs, however there are exceptions. Switch to fdtdec_get_addr_size_auto_noparent(), which takes the #address/size-cells values into consideration, otherwise the reset controller node register offset is incorrectly parsed. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-30ARM: rmobile: Convert Gen2 Blanche to DM_SPI{,_FLASH}Marek Vasut
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-28configs: a64-olinuxino-emmc: add eMMC boot part config commandsPetr Štetiar
mmc bootbus and partconf commands are needed in order to be able to configure booting from separate boot0/boot1 eMMC partitions. Signed-off-by: Petr Štetiar <ynezz@true.cz> [jagan: rebase on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-28vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader.Kristian Amlie
EFI was disabled in f95b8a4b5f64f because of the missing DTB file, and indeed, the DTB file is required to load recent versions of GRUB (2.04) correctly. Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2020-03-28efi_loader: only reserve memory if fdt node enabledHeinrich Schuchardt
Sub-nodes of /reserved-memory may be disabled. In this case we should not reserve memory in the memory map. Reported-by: Patrick DELAUNAY <patrick.delaunay@st.com> Fixes: fef907b2e440 ("efi_loader: create reservations after ft_board_setup") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Atish Patra <atish.patra@wdc.com>
2020-03-28cmd: efidebug: fix int to pointer castHeinrich Schuchardt
On 32 bit systems fix warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Fixes: a415d61eac26 ("cmd: map addresses to sysmem in efidebug memmap") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-28test/py: UEFI helloworld requires OF_CONTROLHeinrich Schuchardt
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined and test_efi_helloworld_net() fails. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-27Merge branch '2020-03-27-master-imports'Tom Rini
- Update a few MAINTAINERS entries - cache alignment fix in ext4 code - Two small test fixes
2020-03-27test: typo decompressionHeinrich Schuchardt
%s/decopmression/decompression/ Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-03-27MAINTAINERS: add myself as maintainer of fs/btrfsMarek Behún
Signed-off-by: Marek Behún <marek.behun@nic.cz>
2020-03-27fs: ext4: Fix alignment of cache buffersJan Kiszka
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid access errors like CACHE: Misaligned operation at range [be0231e0, be0235e0] seen on the MCIMX7SABRE. Fixes: d5aee659f217 ("fs: ext4: cache extent data") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-03-27MAINTAINERS: Add usb.h entry to usbMarek Vasut
Add usb.h file into the USB list. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
2020-03-27test/py: mmc: Fix 'mmc info' testcaseHarald Seiler
Commit 41e30dcf8796 ("cmd: mmc: Make Mode: printout consistent") fixed the layout of `mmc info` output. Reflect this change in the respective testcase. Also fix a typo in the documentation. Fixes: 41e30dcf8796 ("cmd: mmc: Make Mode: printout consistent") Signed-off-by: Harald Seiler <hws@denx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-03-27Revert "vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader."Tom Rini
Currently this causes failures of the platform when running the EFI loader tests, so disable it for now. This reverts commit af827140e5965e5bb2bcad1c53ca8419b428ff6d. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-26Merge tag 'u-boot-rockchip-20200327' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fixed for rv1108 and elgin-rv1108 board - Fix the keyboard from USB instead of CrOS EC
2020-03-26rockchip: mkimage: Use an existing macro instead of a decimal valueMiquel Raynal
Depending on the SoC, a header of four characters is prepended to the image. There is already a macro defining the number of characters: RK_SPL_HDR_SIZE, so use it instead of hardcoding "4". Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26rv1108: Fix boot regressionOtavio Salvador
Since commit 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") the following boot regression is seen: U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB initcall sequence 67fd12a0 failed at call 6000b927 (err=-22) This happens because the above commit missed to include the "rockchip-u-boot.dtsi" for rv1108, so include this file like it done for other Rockchip SoC dtsi's. Fixes: 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26elgin-rv1108: Avoid adc_channel_single_shot errorOtavio Salvador
Currently the following error message is seen during boot: U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB APLL: 600000000 DPLL:1200000000 GPLL:1188000000 ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000 MMC: dwmmc@30110000: 0 Loading Environment from MMC... OK In: serial@10210000 Out: serial@10210000 Err: serial@10210000 Model: Elgin RV1108 R1 board rockchip_dnl_key_pressed: adc_channel_single_shot fail! .... Since the elgin-rv1108 does not use ADC to read the download key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid such error. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26elgin-rv1108: Use rk_board_late_init() for GPIO settingsOtavio Salvador
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f for per-boar init") the function that configure the board GPIOs is no longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected. These GPIOs do not need to be configured in such early stagem, so change it to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y to fix the regression. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26ARM: dts: Activate pullups in the console pins on rv1108-elgin-r1Otavio Salvador
In order to make the console pins more robust to noise, activate the pullups and increase its drive strength. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26rockchip: Change keyboard input from CrOS EC keyboard to a USB keyboardPeter Robinson
These boards aren't ChromeOS devices so won't have a cros-ec-keyb input as it's the keyboard available via the ChromeOS Embedded Controller. Update them to use a USB keyboard which would actually be available. Also enable the usb keyboard option for those devices that don't have it enabled already. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26rockchip: evb-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-03-26rockchip: elgin-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2020-03-23vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader.Kristian Amlie
EFI was disabled in f95b8a4b5f64f because of the missing DTB file, and indeed, the DTB file is required to load recent versions of GRUB (2.04) correctly. Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2020-03-23Merge tag 'efi-2020-04-rc4-5' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc4 (5) This series contains bug fixes for the UEFI sub-system: * report correct variable length in GetNextVariable() * correct copying direction if freestanding memmove() * remove const for parameter of GetNextVariableName() * correct function descriptions Unit tests are added and adjusted.
2020-03-22efi_loader: definition of GetNextVariableName()Heinrich Schuchardt
'vendor' is both an input and an output parameter. So it cannot be constant. Fixes: 0bda81bfdc5c ("efi_loader: use const efi_guid_t * for variable services") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_selftest: test CalculateCrc32, CopyMem, SetMemHeinrich Schuchardt
Provide unit tests for CalculateCrc32(), CopyMem(), SetMem(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: fix freestanding memmove()Heinrich Schuchardt
For EFI binaries we have to provide an implementation of memmove() in efi_freestanding.c. Before this patch the memmove() function was copying in the wrong direction. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: description efi_convert_pointer()Heinrich Schuchardt
Correct the description of function efi_convert_pointer(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: simplify logical expression in efi_disk_add_dev()Heinrich Schuchardt
To check if a variable is non-zero there is no need for '!= 0'. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_selftest: check length reported by GetNextVariableName()Heinrich Schuchardt
GetNextVariableName should report the length of the variable including the final 0x0000 in bytes. Check this in the unit test. Increase the buffer size for variable names. 40 bytes is too short. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: correct reported length in GetNextVariable()Heinrich Schuchardt
The runtime service GetNextVariable() returns the length of the next variable including the closing 0x0000. This length should be in bytes. Comparing the output of EDK2 and U-Boot shows that this is currently not correctly implemented: EDK2: OsIndicationsSupported: 46 PlatformLang: 26 PlatformLangCodes: 36 U-Boot: OsIndicationsSupported: 23 PlatformLang: 13 PlatformLangCodes: 18 Provide correct length in GetNextVariable(). Fixes: d99a87f84b75 ("efi_loader: implement GetNextVariableName()") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: fix function descriptions in efi_disk.cHeinrich Schuchardt
Use Sphinx style for function descriptions. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-22efi_loader: description of efi_variable.cHeinrich Schuchardt
Correct the file description. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-03-18sunxi: Remove no longer needed default options from defconfigsAndre Przywara
Now that those common Allwinner config symbols are defined automatically for all boards in their Kconfig files, we can remove the now redundant definitions from the boards' _defconfig files. Some boards had a differing definiton for some of those symbols, it looks like mostly to "merge races" when the symbol was introduced (new board *_defconfig file missed the "add symbol to all files" patch). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: Move common defconfig options to KconfigAndre Przywara
Some config symbols are found in *almost* every _defconfig file for Allwinner boards, because those options are actually a platform choice, and not a per-board decision. Some of these options are older, some have recently been added. Move those options to be set for all Allwinner boards in their respective Kconfig files. The rationales are as follows: - NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of address space only, starting at 1 GB. So it's always one bank. - SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC accesses, we don't care about filesystems or partitions in there, so there is no need to define those symbols at all. - USE_PREBOOT: We start USB early when a keyboard is configured, using the preboot env variable, so we need to set this variable. - SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this symbol to be set (according to 8d8ee47e03e). - SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa55428, specifying this reduces the latency of the USB keyboard handling, so this was formerly enabled in config headers for all Allwinner boards. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: Pine H64: Enable SPI booting in defconfigAndre Przywara
The Pine H64 board comes with some onboard SPI flash chip, which is perfect for loading SPL, ATF and U-Boot proper from there. Enable the functionality in the defconfig, so that we use sunxi-fel to transfer a bootable image to the NOR flash. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: SPL SPI: Add SPI boot support for the Allwinner H6 SoCAndre Przywara
The Allwinner H6 SoC uses a quite different memory map, also changes the clocks quite a bit. This requires some changes to the SPL SPI routine, which hardcodes these values so far. Using the just introduced helper functions to determine base address and SPI controller generation, we can cover some of these differences easily. The clock setup is different, so requires some explicit code changes there (reset and clock gate in one register at a different address). Also we need to change the pinmux function to use a different set of pins that the H6 uses for SPI0. Eventually we can enable the H6 to use SPI booting in Kconfig. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: SPL SPI: Add SPI boot support for the Allwinner R40 SoCAndre Przywara
Now that we can easily select an SoC specific SPI0 base address, adding support for the Allwinner R40 is fairly trivial: We set the base address, add this SoC to the ones that use PC23 and enable it in Kconfig. This allows booting from SPI flash on R40 boards. Tested on a Bananapi M2 Berry with SPI flash connected to the header pins. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: SPL SPI: Introduce is_sun6i_gen_spi()Andre Przywara
So far we were using the CONFIG_SUNXI_GEN_SUN6I symbol to select between the two SPI controller generations used on Allwinner SoCs. This is a convenience symbol to roughly differentiate between "older" and "newer" generation of SoCs. The H6 SoCs is the newest SoC so far, but is sufficiently different to not define this symbol. However it is using a SPI controller compatible to the "new gen" SoCs. To prepare for H6 support, we replace the check for this single symbol with an explicit function, which can later be extended. For now we just return CONFIG_SUNXI_GEN_SUN6I in there, so this does not create a functional change. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: SPL SPI: Split off SPI0 base addressAndre Przywara
So far on all supported Allwinner SoCs we find the old generation SPI controller always at address 0x1c05000, and the new generation one at 0x1c68000. However the Allwinner R40 SoC has a new generation SPI at the old address, and the H6 uses a completely different address. So split off the base address from the respective SPI registers, by changing the #defines to just contain offsets. The base address is provided by a function, so it can easily be extended later when support for those SoCs materialises. This does not change the code size (since the toolchain is clever enough to optimise this properly), also does not bring any functional change at this point. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- Revert "sunxi: psci: avoid error address-of-packed-member"
2020-03-18Merge tag 'efi-2020-04-rc4-4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc4 (4) This series fixes several bugs: * consider the /reserved-memory node in the device tree * consider memory reservations created in ft_board_setup() * correct output of 'efidebug memmap' on the sandbox * correct the definition of efi_capsule_header() Furthermore some definitions needed for future patches are added to header files.
2020-03-18Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fix sbi_remote_sfence_vma{,_asid}. - Avoid calling sbi_clear_ipi(). - Add new SBI v0.2 extensions support.
generated by cgit (git 2.34.1) at 2025-01-29 13:37:54 +0000