| Age | Commit message (Collapse) | Author |
|---|
|
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
Signed-off-by: Lucas Stach <dev@lynxeye.de>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <TWarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:
git clean -f -d -x
./MAKEALL ventana
"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.
I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
When I set up Tegra's config files to put the environment into eMMC, I
assumed that CONFIG_ENV_OFFSET was a linearized address relative to the
start of the eMMC device, and spanning HW partitions boot0, boot1,
general* and the user area in order. However, it turns out that the
offset is actually relative to the beginning of the user area. Hence,
the environment block ended up in a different location to expected and
documented.
Set CONFIG_SYS_MMC_ENV_PART=2 (boot1) to solve this, and adjust
CONFIG_ENV_OFFSET to be relative to the start of boot1, not the entire
eMMC.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
eMMC devices may have hardware-level partitions: 2 boot partitions,
up to 4 general partitions, plus the user area. This change introduces
optional config variable CONFIG_SYS_MMC_ENV_PART to indicate which
partition the environment should be stored in: 0=user, 1=boot0, 2=boot1,
4..7=general0..3. This allows the environment to be kept out of the user
area, which simplifies the management of OS-/user-level (MBR/GPT)
partitions within the user area.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This commit enables NAND support on the Tamonten Evaluation Carrier and
adds the corresponding device tree nodes. Furthermore, the U-Boot
environment can now be stored in NAND.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
In order for cache invalidation and flushing to work properly, the data
and OOB buffers must be aligned to full cache lines.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This enables NAND support for the Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
A device tree is used to configure the NAND, including memory
timings and block/pages sizes.
If this node is not present or is disabled, then NAND will not
be initialized.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a flash node to handle the NAND, including memory timings and
page / block size information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a NAND controller along with a bindings file for review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add selection of NAND flash pins to the funcmux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The NAND layer needs to use cache-aligned buffers by default. Towards this
goal. align the default buffers and their members according to the minimum
DMA alignment defined for the architecture.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
We have the timer code in arch/arm/cpu/armv7/omap-common/timer.c that
has been configuring and enabling the timer, so remove our code that
does the same thing by different methods.
Tested on EVM GP, SK-EVM and Beaglebone.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Add a common macros to set the registers for horizontal
and vertical timing.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Fix some issues (some pins were not set as GPIOs)
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
The manufacturer delivers the TAM3517 SOM with 4 MAC address.
They are stored on the EEPROM of the SOM. The patch adds a
function to get their values and set the ethaddr variables.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
AM/DM37x SoCs add the CTRL_WKUP_CTRL register. It contains the
GPIO_IO_PWRDNZ bit, which is required to be set to enable the I/O pads
of gpio_126, gpio_127 and gpio_129.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Tom Rini <trini@ti.com>
|
|
|
|
In order to use the serial interface on the PortuxG20 we need to enable the
level converter first by setting the PC9 pin to high. The level converter needs
some time to settle so we have to use the mdelay() function to wait for some
time. Unfortunately we have no timers available at board_early_init_f() so we
enable the serial output early within board_postclk_init().
Now the U-Boot output looks fine:
| U-Boot 2012.07-00132-gaf1a3b0-dirty (Aug 16 2012 - 18:21:32)
|
| CPU: AT91SAM9G20
| Crystal frequency: 18.432 MHz
| CPU clock : 396.288 MHz
| Master clock : 132.096 MHz
| DRAM: 64 MiB
| WARNING: Caches not enabled
| NAND: 128 MiB
| In: serial
| Out: serial
| Err: serial
| Net: macb0
| Hit any key to stop autoboot: 0
Signed-off-by: Markus Hubig <mhubig@imko.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The board_postclk_init() function can be used to perform operations
that requires a working timer early within the U-Boot init_sequence.
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
* add ram target for EB+CPUx9k2 board (eb_cpux9k2_ram_config)
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The configuration that is common for all Integrator boards may
just as well be stored in a common include file as per pattern
from other boards. This eases maintenance quite a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* fix chip select initialization for frame buffer, this will be
increase frame buffer access speed
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This patch restores the Linkstation's original behaviour when powering off.
Once the (soft) power switch is turned off, linux will reboot and the
bootloader turns off HDD and USB power. Then it loops as long as the switch
is in the off position, before continuing the boot process again.
Additionally, this patch fixes the board function set_led(LED_OFF).
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
|
|
Hi,
This adds to the documenation to explain how to use the
kwbimage.cfg file necessary to generate an image with
prefixed board setup values necessary for the kirkwood
boards.
Signed-off-by: Karl O. Pinc <kop@meme.com>
|
|
Signed-off-by: Karl O. Pinc <kop@meme.com>
|
|
For some reasons we had an own implementaion of dram_init and
dram_init_banksize. This is not needed anymore, use the standard
kirkwood functions instead.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
|
|
According to our last HW measures, this could be raised while still
compatible with the potential delays on the lines.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
|
|
The fanless boards now have a 7-digit (XXXXX-F) board name. This
triggers a border condition when reading this string in the IVM although
this string is smaller than the currenly read string size, but only by 1
character.
This patch corrects this by changing the size check condition for string
length. It is the same change that was done in the platform for this
same bug.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Bigler <stefan.bigler@keymile.com>
|
|
The computation was not correct with low clock values: setting a 1MHz
clock would result in an overlap that would then configure a 25Mhz
clock.
This patch implements a correct computation method according to the
kirkwood functionnal spec. table 600 (Serial Memory Interface
Configuration Register).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
These parameters are used by the the sf probe command that are used by
our update script and they therefore need to be set for all of our
boards.
The timing is the same as for the ENV SPI NOR Flash (since it's the
same physical device) and takes the boco2 delay on the bus into account.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
|
|
Orion5x did not actually write GPIO output values
or input polarities, and ED Mini V2 had bad or
missing values for GPIO settings.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
|
|
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
tx25: Use generic gpio_* calls
config: Always use GNU ld
tools: add kwboot binary to .gitignore file
fdt: Include arch specific gpio.h instead of asm-generic/gpio.h
serial: CONSOLE macro is not used
Conflicts:
board/karo/tx25/tx25.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: voice.shen@atmel.com
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.
To use PMECC in this driver, the user needs to set the PMECC correction
capability, the sector size and ROM lookup table offsets in board config file.
This driver is ported from Linux kernel atmel_nand PMECC patch. The main difference
is in this version it uses registers structure access hardware instead of using macros.
It is tested in 9x5 serial boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
atmel_hw_nand_init_param().
This patch
1. extract the hwecc initialization code into one function. It is a preparation for adding atmel PMECC support.
2. enable CONFIG_SYS_NAND_SELF_INIT. Which make us can configurate the ecc parameters between nand_scan_ident() and nand_scan_tail().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix empty newline at EOF error and move return value check into ifdef]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Add at91sam9x5 series spi flash boot support
Using at91sam9x5ek_spiflash to configure, then it can boot from at25df321
serial flash
SPI mater work in 30Mhz speed, while not 1Mhz speed. This will base on
atmel_spi patch, or else, it will occur receive overrun
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Remove CONFIG_ARCH_CPU_INIT for at91sam9g10ek and at91sam9m10g45ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
