summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-05-23ARM: omap4: add platform specific info for GPMC and ELM controllerspekon gupta
This patch moves platform specific information for GPMC and ELM controller into separate header files, so that any derivative devices do not mess other header files. Platform specific information added into arch-xx/../hardware.h - CPU related platform specific details like base-address of GPMC and ELM Platform specific information added into arch-xx/../mem.h - Generic configs for GPMC and ELM initialization. - Hardware parameters or constrains specific to GPMC and ELM IP like; number of max number of chip-selects available Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-05-23omap3: overo: Use common configurations for OveroAsh Charles
Clean-up the board configuration file for the Gumstix Overo board by including common omap3 definitions from ti_omap3_common.h as suggested here [1]. [1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/185960 Signed-off-by: Ash Charles <ashcharles@gmail.com> Conflicts: include/configs/omap3_overo.h
2014-05-23Allow overo to boot with device treeAsh Charles
Update the board configuration for Gumstix Overo. In particular, add support for zImage and DTB files on boot. Signed-off-by: Ash Charles <ashcharles@gmail.com>
2014-05-23OMAP3: overo: add some Gumstix expansion boardsAsh Charles
Add EEPROM ID switches for Alto35, Arbor43C, Stagecoach, Thumbo, and Turtlecore Gumstix Overo expansion boards. Signed-off-by: Ash Charles <ash@gumstix.com>
2014-05-23Add Board Revision for Wireless chipAsh Charles
Gumstix Overo COMs with board revision 0x4 use a different Wifi and Bluetooth module: Wi2Wi's W2CBW0015. No other code changes are required in u-boot---just handling of this particular board revision. Signed-off-by: Ash Charles <ashcharles@gmail.com>
2014-05-23arm: omap3: Fix omap3_overo SPL boot hangupAsh Charles
Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on Overo. Since some gpio inputs are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Ash Charles <ashcharles@gmail.com>
2014-05-23OMAP3: overo: eliminate hard-coded partition offsetsAsh Charles
The linux kernel is at nand0,3 using the current layout, but is best accessed through the partition label "linux". Since CONFIG_CMD_MTDPARTS is defined the CONFIG_JFFS2 settings are unreferenced; use "setenv partition rootfs" to set the default mtd partition for jffs2. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
2014-05-23OMAP3: overo: increase linux partition to 8 MiBPeter A. Bigot
Linux kernel at version 3.5 is about 3.5 MiB; test kernels for 3.10 exceed 4 MiB. Prepare for future upgrades by increasing the NAND partition now. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
2014-05-23OMAP3: overo: add command support for mtd and ubiAsh Charles
The NAND linux partition format default was changed from jffs2 to ubi in 254973e6df0e48f1a72b67905185c774dcd9f394 but the corresponding commands were not enabled. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
2014-05-23omap: overo: allow the use of a plain text env file instead boot scriptsAsh Charles
Adapted from d70f5480 described below. commit d70f54808dfa83b574e1239c3eccbcf3317343e1 Author: Javier Martinez Canillas <javier@dowhile0.org> Date: Mon Jan 7 03:51:20 2013 +0000 omap4: allow the use of a plain text env file instead boot scripts For production systems it is better to use script images since they are protected by checksums and carry valuable information like name and timestamp. Also, you can't validate the content passed to env import. But for development, it is easier to use the env import command and plain text files instead of script-images. Since both OMAP4 supported boards (Panda and TI SDP4430) are used primarily for development, this patch allows U-Boot to load env var from a text file in case that an boot.scr script-image is not present. The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
2014-05-23esdhc/usdhc: Fix warning when CONFIG_SYS_FSL_ESDHC_USE_PIO is not setTom Rini
In 7168977 we made calls to check_and_invalidate_dcache_range() conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function in this case as well. Signed-off-by: Tom Rini <trini@ti.com>
2014-05-23Merge branch 'master' of git://git.denx.de/u-boot-mmcTom Rini
2014-05-23cmd_mmc: use new mmc_select_hwpart() functionStephen Warren
The implementation of mmc_select_hwpart() was cribbed from do_mmcops(). Update do_mmcops() to call mmc_select_hwpart() to avoid duplication. <panto> Manual patch update due to patch order. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-23mmc: provide a select_hwpart implementation for get_device()Stephen Warren
This enables specifying which eMMC HW partition to target for any U-Boot command that uses the generic get_partition() function to parse its command-line arguments. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-23disk: support devices with HW partitionsStephen Warren
Some device types (e.g. eMMC) have hardware-level partitions (for eMMC, separate boot and user data partitions). This change allows the user to specify the HW partition they wish to access when passing a device ID to U-Boot Commands such as part, ls, load, ums, etc. The syntax allows an optional ".$hwpartid" to be appended to the device name string for those commands. Existing syntax, for MMC device 0, default HW partition ID, SW partition ID 1: ls mmc 0:1 / New syntax, for MMC device 0, HW partition ID 1 (boot0), SW partition ID 2: ls mmc 0.1:2 / For my purposes, this is most useful for the ums (USB mass storage gadget) command, but there's no reason not to allow the new syntax globally. This patch adds the core support infra-structure. The next patch will provide the implementation for MMC. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-23cmd_part: fix typo in part command help textStephen Warren
All the sub-commands start with the main command name, but it was missing from one of the help texts. <panto> typos fix. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-05-23eMMC: cmd_mmc.c adds the 'rpmb' sub-command for the 'mmc' commandPierre Aubert
This sub-command adds support for the RPMB partition of an eMMC: * mmc rpmb key <address of the authentication key> Programs the authentication key in the eMMC This key can not be overwritten. * mmc rpmb read <address> <block> <#count> [address of key] Reads <#count> blocks of 256 bytes in the RPMB partition beginning at block number <block>. If the optionnal address of the authentication key is provided, the Message Authentication Code (MAC) is verified on each block. * mmc rpmb write <address> <block> <#count> <address of key> Writes <#count> blocks of 256 bytes in the RPMB partition beginning at block number <block>. The datas are signed with the key provided. * mmc rpmb counter Returns the 'Write counter' of the RPMB partition. The sub-command is conditional on compilation flag CONFIG_SUPPORT_EMMC_RPMB Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Pierre Aubert <p.aubert@staubli.com> CC: Wolfgang Denk <wd@denx.de>
2014-05-23Add the function 'confirm_yesno' for interactivePierre Aubert
User's confirmation is asked in different commands. This commit adds a function for such confirmation. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
2014-05-23eMMC: add support for operations in RPMB partitionPierre Aubert
This patch adds functions for read, write and authentication key programming for the Replay Protected Memory Block partition in the eMMC. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
2014-05-23mmc: Handle switch error status bit in MMC card statusAndrew Gabbasov
MMC switch command for unsupported feature (e.g. bus width) sets a switch error bit in card status. This bit should be checked, and, if it's set, no access with new controller settings should be performed. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-05-23mmc: postponed needless timer initializationMateusz Zalega
mmc_init() doesn't call get_timer() anymore if MMC is already initialized. <panto> Minor formatting fix. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
2014-05-23Add board_mmc_init(...) function for init mmc1 onlyHannes Petermaier
Since B&R boards uses only MMC-Controller #1, it only wastes time if we initialize #0 first to see that there is nothing. Cc: <trini@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-05-22Merge branch 'fpga' of git://www.denx.de/git/u-boot-microblazeTom Rini
2014-05-22Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-05-22Merge branch 'pr-15052014' of git://git.denx.de/u-boot-usbTom Rini
2014-05-22Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2014-05-22esdhc/usdhc: Fix PIO mode bug in fsl_esdhc driverYe.Li
When configure the fsl_esdhc driver to PIO mode by defining "CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail. Two bugs in the driver to cause the issue: 1. The read buffer was invalidated after reading from DATAPORT register, which should be only applied to DMA mode. The valid data in cache was overwritten by physical memory. 2. The watermarks are not set in PIO mode, will cause according state not be set. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Ye.Li <B37916@freescale.com>
2014-05-21arm: rmobile: lager: Enable CONFIG_SYS_GENERIC_BOARDNobuhiro Iwamatsu
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for lager. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Enable CONFIG_SYS_GENERIC_BOARDNobuhiro Iwamatsu
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for koelsch. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: armadillo800eva: Enable CONFIG_SYS_GENERIC_BOARDNobuhiro Iwamatsu
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for armadillo800eva. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Fix QoS revision 0.240 and 0.320Nobuhiro Iwamatsu
Add register define of DBSC3 operation adjustment register, and add initial value. Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: r8a7791: Fix MOD_SEL3 function table about FN_SEL_IEBNobuhiro Iwamatsu
FN_SEL_IEB is assigned 2bit, and 2bit can represent 4 patterns. However FN_SEL_IEB but we only use 3. It adds empty patterns as 0. Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Add support ext4/fat write commandNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Add support ext4/fat write commandNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Add support command and filesystems of VFATNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Add support USB controllerNobuhiro Iwamatsu
Lager board has USB ports. This add support of USB controller of rmobile. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Add support command and filesystems of VFATNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Add support USB controllerNobuhiro Iwamatsu
Koelsch board has USB ports. This add support of USB controller of rmobile. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21gpio: r8a7790-gpio: Fix typo in macroNobuhiro Iwamatsu
Fix typo from __ASM_R8A7790_H__ to __ASM_R8A7790_GPIO_H__. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21gpio: r8a7791-gpio: Fix typo in macroNobuhiro Iwamatsu
Fix typo from __ASM_R8A7791_H__ to __ASM_R8A7791_GPIO_H__. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Enable optimization of thumbNobuhiro Iwamatsu
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization of thumb. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Remove CONFIG_USE_ARCH_MEMSET and MEMCPYNobuhiro Iwamatsu
Because do not need these feature to lager board, this delete it. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: lager: Remove define of SCIF registerNobuhiro Iwamatsu
The define of SCIF register was already defined in rcar-base.h. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Enable optimization of thumbNobuhiro Iwamatsu
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization of thumb. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Remove CONFIG_USE_ARCH_MEMSET and MEMCPYNobuhiro Iwamatsu
Because do not need these feature to koelsch board, this delete it. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: koelsch: Remove define of SCIF registerNobuhiro Iwamatsu
The define of SCIF register was already defined in rcar-base.h. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21arm: rmobile: Add define of SCIF register for R8A7790 and R8A7791Nobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-20fpga: Added support to load bit stream from SD/MMCSiva Durga Prasad Paladugu
Added support to load a bitstream image in chunks by reading it in chunks from SD/MMC. Command format: loadfs [dev] [address] [image size] [blocksize] <interface> [<dev[:part]>] <filename> Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20zynq: Enable fpga loadp and loadbp commandsMichal Simek
Use new fpga commands for loading partial bitstreams. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20fpga: zynqpl: Clean partial bitstream handlingMichal Simek
Do not do partial bitstream detection based on bitstream size and use bitstream_type argument which is passed from the fpga core. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-04 09:36:31 +0000