summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-12ARM: dts: stm32mp1: Add adc nodesPatrice Chotard
Add adc related nodes. These nodes are used to detect the current supplied by USB type-C power in port on DK1 and DK2 boards. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12Board: stm32mp1: Add supply current boot informationPatrice Chotard
For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2: range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected If detected current is < 3A, red led is kept ON after blinking. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Update README filePatrice Chotard
Update README with DK1 and DK2 boards related informations Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12ARM: dts: stm32: Synchronize DT with kernel onePatrice Chotard
This patch synchronizes U-boot DT with kernel one This is based on https://patchwork.kernel.org/cover/10797115/ This patch adds initial support of STM32MP157 discovery boards: - Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1). This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Several connections are available on this boards: 4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ... - Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2). This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a) and Murata wifi/BT combo is added. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: add NVM update support in fuse commandPatrick Delaunay
Add functions to read/update the non volatile memory of STPMIC1 (8 bytes-register at 0xF8 address) and allow access with fuse command (bank=1, word > 0xF8). For example: STM32MP> fuse read 1 0xf8 8 Reading bank 1: Word 0x000000f8: 000000ee 00000092 000000c0 00000002 Word 0x000000fc: 000000f2 00000080 00000002 00000033 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: dts: activate psci-1.0Patrick Delaunay
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for power off command; TF-A for stm32mp15x supports PSCI 1.0. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add command poweroffPatrick Delaunay
Activate the command poweroff by default for STM32MP1: - with PCSI from TF-A for trusted boot - with PMIC sysreset request for basic boot (SYSRESET_POWER) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12pmic: stpmu1: add power switch off supportPatrick Delaunay
Add sysreset support, and support power switch off request, needed by poweroff command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12regulator: stpmu1: update buck1 rangePatrick Delaunay
SW impact for Rev 1.2 of STPMIC1 in U-Boot: Buck converters output voltage change for Buck1 => Vdd min 0,725 to max 1,5V instead of 0.6V to 1.35V (see STPMIC1 datasheet / chapter 5.3 Buck converters) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: Replace OTP read by SHADOW readPatrick Delaunay
Replace STM32_BSEC_OTP() by STM32_BSEC_SHADOW() to increase read performance. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: shadow all the upper OTP (no secure) during bootPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: use device tree new compatiblePatrick Delaunay
Update bsec driver to use the device tree provided by Kernel. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: basic boot: SPL enable access to GPIOZ bankPatrick Delaunay
SPL need to set GPIOZ_SECCFGR = 0 to enable access to GPIOZ bank (open security). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: align serial number on bootromPatrick Delaunay
Always use upper case for serial number. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add syscfg initializationPatrick Delaunay
Initialize the system configuration for basic boot - update interconnect setting - disable pull-down for boot pin - enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI - activate I/O compensation Done by SSBL = TF-A for trusted boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add some syscon drivers for syscfg and etpzcPatrick Delaunay
Add SYSCON driver for syscfg and etpzc and reorder in alphabetics order Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: activated some configurationPatrick Delaunay
Add configuration useful for test - FIT support - MEMTEST - DFU - CACHE - TIME - TIMER Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update memory layoutPatrick Delaunay
Update the memory layout to be aligned with other platform and avoid overlap with 32MB Linux kernel (multiv7 image). + Kernel => 32MiB offset = 0xC2000000 and increase the bootm size to 32MiB + FDT => 64MiB offset = 0xc4000000 + SCRIPT => 65Mib offset = 0xc4100000 + PXESCRIPT => 66Mib offset = 0xc4200000 + SPLASHIMAGE => 67Mib offset = 0xc4300000 + RAMDISK => 68Mib offset = 0xc4400000 (not limited size) In sources/boot/u-boot/doc/README.distro + kernel_addr_r: A size of 16MB for the kernel is likely adequate. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable. + ramdisk_addr_r: It is recommended that this location be highest in RAM out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size and use any available RAM. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + scriptaddr: A size of 1MB for extlinux.conf is more than adequate. For suggestions on memory locations for ARM systems, you must follow the guidelines specified in Documentation/arm/Booting in the Linux kernel tree. And in sources/linux-stm32mp/Documentation/arm/Booting The zImage may also be placed in system RAM and called there. The kernel should be placed in the first 128MiB of RAM. It is recommended that it is loaded above 32MiB in order to avoid the need to relocate prior to decompression, which will make the boot process slightly faster. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: support forced boot modePatrick Delaunay
The boot mode can be forced by key press or by TAMP register, requested in kernel by syscon-reboot-mode tamp: tamp@5c00a000 { compatible = "simple-bus", "syscon", "simple-mfd"; reg = <0x5c00a000 0x400>; reboot-mode { compatible = "syscon-reboot-mode"; offset = <0x150>; /* reg20 */ mask = <0xff>; mode-normal = <0>; mode-fastboot = <0x1>; mode-recovery = <0x2>; mode-stm32cubeprogrammer = <0x3>; mode-ums_mmc0 = <0x10>; mode-ums_mmc1 = <0x11>; mode-ums_mmc2 = <0x12>; }; }; Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: activate FASTBOOT on eMMCPatrick Delaunay
activate Fastboot for eMMC on EV1 board (mmc1) $> sudo apt-get install android-tools-adb android-tools-fastboot $> fastboot -i 0x0483 getvar bootloader-version Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update bootcmdPatrick Delaunay
Clearly separate bootcmd for stm32mp1 board (bootcmd_stm32mp) and preboot management. That solve issue for fastboot continue command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: spl: hang with trace when DDR init failedPatrick Delaunay
When DDR initialization failed, print error message and stop the SPL execution. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: cosmetic: add comment on psci_migrate_info_type return valuePatrick Delaunay
Add explaination for the return value of psci_migrate_info_type: 2 = Trusted OS. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: cosmetic cleanup KconfigPatrick Delaunay
Cosmetic cleanup in mach-stm32mp Kconfig - remove duplicated SPL_DRIVERS_MISC_SUPPORT - update help for TARGET_STM32MP1 - set value for NR_DRAM_BANKS - remove one comment as DEBUG_UART is deactivated by default - include board Kconfig at the end of the file Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: spl: add spl_display_printPatrick Delaunay
SPL displays the board model from device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update print_cpuinfo()Patrick Delaunay
Display CPU part number and package information. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update boot mode managementPatrick Delaunay
- export the function get_bootmode() and reused it in spl code - manage uart instance by alias (prepare v4.19 binding) - solve issue on nand instance - restore console for uart boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add runtime information in environmentPatrick Delaunay
Set board name with the first dts compatible found in DT code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG The result with DEVICE_TREE=stm32mp157c-ev1 is: STM32MP> env print board=stm32mp1 board_name=stm32mp157c-ev1 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: display board informationPatrick Delaunay
Implement checkboard() function to display - the boot chain used: basic or trusted - the board compatible in device tree - the board identifier and revision, saved in OTP59 for ST boards Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: access with SMC for trusted bootPatrick Delaunay
As BSEC is secure aware, all register access need to be done by TF-A for TRUSTED boot chain, when U-Boot is executed in normal world. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add trusted boot with TF-APatrick Delaunay
Add support of trusted boot, using TF-A as first stage bootloader, The boot sequence is BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32 The TF-A monitor provides secure monitor with support of SMC - proprietary to manage secure devices (BSEC for example) - PSCI for power The same device tree is used for STMicroelectronics boards with basic boot and with trusted boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12mmc: omap_hsmmc: Set 3.3V for IO voltageFaiz Abbas
Pbias voltage should match the IO voltage set for the SD card. With the latest pbias change to 3.3V, update the capabilities and IO voltages settings to 3.3V. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12ARM: dts: dra71-evm: Correct evm_sd regulator max voltageFaiz Abbas
Correct vpo_sd_1v8_3v3 regulator max voltage to 3.3V Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com>
2019-04-12ARM: dts: dra7: Change pbias voltage to 3.3VFaiz Abbas
As per recent TRM[1], PBIAS cell on dra7 devices supports 3.3v and not 3.0v as documented earlier. Update PBIAS regulator max voltage and the voltage written in the driver to reflect this. [1] http://www.ti.com/lit/pdf/sprui30 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12ARM: am3517_evm: Add spl_start_uboot for Falcon ModeAdam Ford
When booting the am3517-evm, the following message appears: SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! This patch implements spl_start_uboot to clear this message and allow device to know if it should boot U-Boot or kernel. Fixes: 1c6b6f383a41 ("ARM: am3517_evm: Enable Falcon Mode") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12ti: keystone2: Move CONFIG_ISW_ENTRY_ADDR to a common placeTom Rini
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific notion but rather "where is our previous stage loaded in memory?" option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for our HS builds that are not using SPL anyhow. Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
2019-04-12board: ti: am335x: Remove non DM_ETH codeFaiz Abbas
With DM_ETH enabled in am335x devices, remove all the unused non-DM code. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12configs: am335x_evm: Update VCI StringFaiz Abbas
Update VCI string to keep it compatible with legacy test setups. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-12configs: am335x_evm: Add Support for SPL_ETHFaiz Abbas
Add Support for booting from Ethernet. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12configs: am335x_evm: Reduce size of SPLFaiz Abbas
Make some room in SPL by getting rid of unnecessary configs. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: am335x: Add platdata for cpsw in SPLFaiz Abbas
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL is enabled. Use static platdata instead to save space. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: ti: cpsw: Enable DM_FLAG_PRE_RELOCFaiz Abbas
Add DM_FLAG_PRE_RELOC to make the driver probe in SPL. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: ti: cpsw: Block off ofdata_to_platdata with OF_CONTROLFaiz Abbas
The ofdata_to_platdata function should not be called if OF_CONTROL is not enabled because fdtdec_* calls will fail. Block the function with OF_CONTROL Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: ti: cpsw-common: Isolate getting syscon address from assigning macidFaiz Abbas
ti_cm_get_macid() is used to get a syscon node from the dt, read the efuse address and then assign the macid read from the address. Divide these two steps into separate functions one of which can be called from ofdata_to_platdata() while the other can be called from _probe(). This ensures that platdata can be assigned statically in a board file when OF_CONTROL is not enabled. Also add a macid_sel_compat in private data to get information about the macid byte placement. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: ti: cpsw: Convert cpsw_platform_data to a pointer in cpsw_privFaiz Abbas
Convert cpsw_platform_data to a pointer in cpsw_priv. Allocate it dynamically and assign it as a part of eth_pdata. This helps in isolating platform data handling and implementing platdata for SPL in a board file. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: ti: cpsw: Move cpsw_phy_sel() to _probe()Faiz Abbas
cpsw_phy_sel() is a configuration step that should not be in ofdata_to_platdata(). Add phy_sel_compat to the cpsw_platform_data structure so that it is accessible in _probe. Then move the call of cpsw_phy_sel() to _probe. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12net: Add priv_pdata to eth_pdataFaiz Abbas
Add a priv member for eth_pdata for platform specific platform data. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
generated by cgit (git 2.34.1) at 2025-01-08 18:21:38 +0000