summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-10-18x86: Move table csum into separate headerAlexander Graf
We need the checksum function without all the other table functionality soon, so let's split it out into its own header file. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-17Prepare v2016.11-rc2Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-15Merge git://git.denx.de/u-boot-mpc85xxTom Rini
2016-10-15spl: move FDT_FIXUP_PARTITIONS to KconfigHeiko Schocher
Move FDT_FIXUP_PARTITIONS to Kconfig and cleanup existing uses. Signed-off-by: Heiko Schocher <hs@denx.de>
2016-10-15spl: move SYS_OS_BASE to KconfigHeiko Schocher
Move SYS_OS_BASE to Kconfig and cleanup existing uses. Signed-off-by: Heiko Schocher <hs@denx.de> [trini: Also migrate a4m2k] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-14spl: move SPL_OS_BOOT to KconfigHeiko Schocher
Move SPL_OS_BOOT to Kconfig and cleanup existing uses. Signed-off-by: Heiko Schocher <hs@denx.de>
2016-10-14test/py/tests/test_sleep.py: Add check for CONFIG_CMD_MISCTom Rini
We can only run this command if the sleep command is enabled and that depends on CONFIG_CMD_MISC Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-14ARM: create .secure_stack section only for PSCIMasahiro Yamada
Jon Master reports that QEMU refuses to load a U-Boot image built with CONFIG_ARMV7_NONSEC, but without CONFIG_ARMV7_PSCI since commit 5a3aae68c74e ("ARM: armv7: guard memory reserve for PSCI with #ifdef CONFIG_ARMV7_PSCI"). It looks like only PSCI that needs the Secure stack, so move the #ifdef to guard the whole of .secure_stack allocation in order not to create the empty section. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Jon Masters <jcm@redhat.com> Link: http://patchwork.ozlabs.org/patch/664025/
2016-10-14arch: powerpc: Remove unused dts frequency fixup for lbc_clkPrabhakar Kushwaha
lbc_clk is used to fixup dts as "bus frequency". It is not being used by Linux IFC and eLBC driver. So remove unused "bus frqeuency" fix-up of devicre tree. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-14pbl: use "wait" command instead of "flush" commandZhao Qiang
PBL flush command is restricted to CCSR memory space. So use WAIT PBI command to provide enough time for data to get flush in target memory. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> [York Sun: rewrap commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-14Txxx/RCW: Split unified RCW to RCWs for sd, spi and nand.Zhao Qiang
T series boards use unified RCW for sd, spi and nand boot. Now split txxx_rcw.cfg to txxx_sd_rcw.cfg, txxx_spi_rcw.cfg and txxx_nand_rcw.cfg for SPI/NAND/SD boot. And modify RCW[PBI_SRC] for them: PBI_SRC=5 for SPI 24-bit addressing PBI_SRC=6 for SD boot PBI_SRC=14 for IFC NAND boot Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-13Merge git://git.denx.de/u-boot-fdtTom Rini
2016-10-13libfdt: Drop inlining of fdt_path_offset()Simon Glass
The fdt_path_offset() function is not inlined in upstream libfdt. Adjust U-Boot's version to match. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-13libfdt: Sync fdt_for_each_subnode() with upstreamSimon Glass
The signature for this macro has changed. Bring in the upstream version and adjust U-Boot's usages to suit. Signed-off-by: Simon Glass <sjg@chromium.org> Update to drivers/power/pmic/palmas.c: Signed-off-by: Keerthy <j-keerthy@ti.com> Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
2016-10-13libfdt: Bring in upstream stringlist functionsSimon Glass
These have now landed upstream. The naming is different and in one case the function signature has changed. Update the code to match. This applies the following upstream commits by Thierry Reding <treding@nvidia.com> : 604e61e fdt: Add functions to retrieve strings 8702bd1 fdt: Add a function to get the index of a string 2218387 fdt: Add a function to count strings Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-13libfdt: Sync up with upstreamSimon Glass
This includes small changes to the following functions, from upstream commit 6d1832c: - fdt_get_max_phandle() (upstream commit 84e0e134) - fdt_node_check_compatible (upstream commit 53bf130b) - fdt_setprop_inplace_namelen_partial() to remove useless brackets and use idx instead of index - _fdt_resize_property() to use idx instead of index - _fdt_splice() (upstream commit d4c7c25c) It also includes various typo fixes in libfdt.h Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-13libfdt: Fix undefined behaviour in fdt_offset_ptr()David Gibson
Using pointer arithmetic to generate a pointer outside a known object is, technically, undefined behaviour in C. Unfortunately, we were using that in fdt_offset_ptr() to detect overflows. To fix this we need to do our bounds / overflow checking on the offsets before constructing pointers from them. Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-13cmd/fdt: add possibilty to have 'extrasize' on fdt resizeHannes Schmelzer
Sometimes devicetree nodes and or properties are added out of the u-boot console, maybe through some script or manual interaction. The devicetree as loaded or embedded is quite small, so the devicetree has to be resized to take up those new nodes/properties. In original the devicetree was only extended by effective 4 * add_mem_rsv. With this commit we can add an argument to the "fdt resize" command, which takes the extrasize to be added. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Simon Glass <sjg@chromium.org>
2016-10-13Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2016-10-13net: smsc95xx: fix DM MAC address readingStephen Warren
eth-uclass.c expects DM-capable Ethernet adapters to implement ops-> read_rom_hwaddr(), or for some other mechanism to set pdata->enetaddr, or for the user to set environment variable $usbethaddr. Without any of these, it will refuse to initialize the device since no valid MAC address is known. Implement this function for the smsc95xx driver. With this feature implemented, there is no point smsc95xx_init_common() re-reading the MAC address from ROM, so ifdef out this code when DM_ETH is enabled. This allows (at least) the built-in Ethernet on the NVIDIA Harmony board to operate again. Fixes: 0990fcb77219 ("net: smsc95xx: Add driver-model support") Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13test: add NFS download testGuillaume GARDET
Add a NFS download test, based on TFTP test. Tested on i.MX6 SabreLite board. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@konsulko.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: Fix cache misalignment message after network load operationsPeter Chubb
After any operation that downloads a file (e.g., pxe get, or dhcp), the buffer containing the downloaded data is flushed. This is unnecessary and annoying. Unnecessary, because the network driver should already have fliushed the cache for the DMAed area, and annoying because it generates a cache misalignment message. Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-13rtl8169: fix cache misalignment message on transmit.Peter Chubb
The call to flush cache on the transmit buffer was misplaced (for very short packets) and asked to flush less than a cacheline. Move the flush cache call to after a short packet has been padded to minimum length (so the padding is flushed too), and round the size up to a cacheline. Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: write enetaddr down to hardware on env_callbackHannes Schmelzer
If mac-address is changed using "setenv ethaddr ...." command the new mac-adress also must be written into the responsible ethernet driver. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: mvneta: fix typo in commentChris Packham
Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: mv88e61xx: Add support for fixed linksChris Packham
On some boards these switches are wired directly into a SERDES interface on another Ethernet MAC. Add the ability to specify these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines a bit mask of these fixed ports. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13net: Add support for mv88e609x switchesChris Packham
The Marvell Link Street mv88e60xx is a series of FastEthernet switch chips, some of which also support Gigabit ports. It is similar to the mv88e61xx series which support Gigabit on all ports. The main difference is the number of ports. Which affects the PORT_COUNT define and the size of the mask passed to mv88e61xx_port_set_vlan(). Other than that it's just a matter of adding the appropriate chip IDs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13board: am335x: Always set eth/eth1addr environment variableRoger Quadros
Ethernet ports might be used in the kernel even if CPSW driver is disabled at u-boot. So always set ethaddr and eth1addr environment variable from efuse. Retain usbnet_devaddr as it is required for SPL USB eth boot. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13board: am335x-icev2: add ethernet phy mode detection logicRoger Quadros
Both ethernet ports can be used as CPSW ethernet (RMII mode) or PRU ethernet (MII mode) by setting the jumper near the port. Read the jumper value and set the pinmux, external mux and PHY clock accordingly. As jumper line is overridden by PHY RX_DV pin immediately after bootstrap (power-up/reset), we have to use GPIO edge detection to capture the jumper line status. As u-boot doesn't provide any infrastructure for GPIO edge detection, we directly access the GPIO registers. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13driver: net: cpsw: add support for RGMII id mode support and RMII clock ↵Mugunthan V N
source selection cpsw driver supports only selection of phy mode in control module but control module has more setting like RGMII ID mode selection, RMII clock source selection. So ported to cpsw-phy-sel driver from kernel to u-boot. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13include: configs: am335x: add Atheros phy supportMugunthan V N
In AM335x GP EVM, Atheros 8031 phy is used, enable the driver as AM335x SoC RGMII delay mode has to be enabled in phy as mentioned in the silicon errata Advisory 1.0.10 Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13drivers: net: phy: atheros: add separate config for AR8031Mugunthan V N
In the current driver implementation, config() callback is common for AR8035 and AR8031 phy. In config() callback, driver tries to configure MMD Access Control Register and MMD Access Address Data Register unconditionally for both phy versions which leads to auto negotiation failure in AM335x EVMsk second port which uses AR8031 Giga bit RGMII phy. Fixing this by adding separate config for AR8031 phy. Reviewed-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13phy: atheros: add support for RGMII_ID, RGMII_TXID and RGMII_RXIDAndrea Merello
This adds support for internal delay on RX and TX on RGMII interface for the AR8035 phy. This is basically the same Linux driver do. Tested on a Zynq Zturn board (for which u-boot support in is my tree; first patch waiting ML approval) Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13Merge branch 'master' of http://git.denx.de/u-boot-mmcTom Rini
2016-10-12Merge git://git.denx.de/u-boot-dmTom Rini
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-10-12Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-10-12Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2016-10-12Merge git://www.denx.de/git/u-boot-marvellTom Rini
2016-10-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/ls1021aqds.h include/configs/ls1021atwr.h
2016-10-12common: Add DISPLAY_BOARDINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12x86: Clean up unused macros in the configuration headersBin Meng
Legacy video driver macros are not needed. Clean them up. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12video: Remove legacy VESA and coreboot framebuffer driversBin Meng
Now that all x86 boards have been converted to DM video, drop the legacy drivers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: coreboot: Convert to use DM coreboot video driverBin Meng
This converts coreboot to use DM framebuffer driver. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Don't do anything in alloc_fb() when plat->size is zeroBin Meng
With DM VESA driver on x86 boards, plat->base/size/align are all zeroes and starting address passed to alloc_fb() happens to be 1MB aligned, so this routine does not trigger any issue. On QEMU with U-Boot as coreboot payload, the starting address is within 1MB range (eg: 0x7fb0000), thus causes failure in video_post_bind(). Actually if plat->size is zero, it makes no sense to do anything in this routine. Add such check there. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12dm: video: Add driver for coreboot framebuffer deviceBin Meng
This adds a DM driver for coreboot framebuffer device. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12vbe: Make vbe_setup_video_priv() publicBin Meng
vbe_setup_video_priv() might be useful to other drivers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12x86: doc: Correct qfw command exampleBin Meng
The kernel load address for zboot should be 0x1000000. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-27 03:05:20 +0000