summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-01-16mpc83xx: fix mpc8313/mpc8315/mpc8349itx Makefiles for silent build (with -s)Kumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16Changes in uboot DDR configuration for MPC8313eRDBPoonam Aggrwal
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for DDR configuration in u-boot code. Some are related to performance, some affect stability and some correct few basic errors in the current configuration. The changes have been tested and found to give better memory latency figures on MPC8313eRDB.LMBench figures prove it. The changes are: - CS0_CONFIG[ AP_n_EN] is changed from 1 to 0 (this may improve performance for application with many read or write to open pages). - CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to 001 (activating all the CS when only one is used may cause unwanted noise on the system) - TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on Tras=45ns) - TIMING_CFG_1[REFREC] changed from 21 clks to 18clks. - TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to comply with the 3 ODT clk requirements) - TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4. - TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks. - DDR_SDRAM_MODE[AL]changed from 0 to 1. - DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks. - DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510. - DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500. The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git The last commit on this tree was 6775c68683a53c7abc778774641aac6f833a2cbf Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com> Cc: Bill HighSmith <Bill.Highsmith@freescale.com> Cc: Razzaz Mazyar <MRazzaz@freescale.com> Cc: Josep P J <PJ.Joseph@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16Enable the isdram command on the MPC8360EMDS boardJerry Van Baren
The isdram command prints out decoded information the "serial presence detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when debugging memory configuration problems. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Add the support for MPC8315ERDB boardDave Liu
The features list: - Boot from NOR Flash - DDR2 266MHz hardcoded configuration - Local bus NOR Flash R/W operation - I2C, UART, MII and RTC - eTSEC0/1 support - PCI host Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Add config of eTSEC emergency priority in SPCRDave Liu
The TSEC emergency priority definition of 831x/837x is different than the definition of 834x in SPCR register. Add the other config of TSEC emergency priority into cpu_init.c Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Remove cache config from MPC8360ERDK.hDave Liu
The MPC8360ERDK board support patch is added before the commit 2c5b48fc205c3e2752910da8f39209ed075929e5 so, miss clean up it. The patch clean up the miss cache config. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16nand: FSL UPM NAND driverAnton Vorontsov
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16OneNAND: Separate U-Boot dependent code from OneNANDKyungmin Park
OneNAND: Separate U-Boot dependent code from OneNAND Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-01-16LWMON5: enable hush shell as command line parserWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-15ADS5121: disable watchdog; enable image timestampsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-15TK885D: fixes for bigger flash sector sizes on new modules;Wolfgang Denk
adjust default environment; disable SCC ethernet (not used on this board). Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-14Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk
2008-01-14QE: fix compile warningDave Liu
qe.c: In function 'qe_upload_firmware': qe.c:390: warning: pointer targets in passing argument 2 uec.c: In function 'uec_initialize': uec.c:1236: warning: 'uec_info' may be used uninitialized Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-01-14ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bitStefan Roese
Now that bit 29 is the USB PHY reset bit, update the Kilauea port to remove the USB PHY reset after powerup. The CPLD will keep the USB PHY in reset (active low) until the bit is set to 1 in board_early_init_f(). Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-13ARM: update mach-types.h from 2.6.24-rc7 Linux kernel treeWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: Fix typo in ads5121.c, adjust default environmentWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: MAX slew rate for PATA pinsJohn Rigby
Signed-off-by: John Rigby <jrigby@freescale.com>
2008-01-13Fix Makefile dependency problem with parallel builds.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8544DS: fix board Makefile for silent build (with -s)Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13PMC440 board: fix board Makefile for out-of-tree buildingWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Makalu: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/masterWolfgang Denk
2008-01-13cmd_nand : fix compiler warning.Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-01-13CFI: Fix CONFIG_FLASH_CFI_LEGACY compilationMichael Schwingen
Signed-off-by: Michael Schwingen <michael@schwingen.org> Acked-by: Stefan Roese <sr@denx.de>
2008-01-13Merge branch 'master' of /home/stefan/git/u-boot/u-bootStefan Roese
2008-01-13MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBESWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8xx FEC driver: fix compiler warning.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Fix Makefile dependencies issues; allow silent buildWolfgang Denk
- get rid of "version" target whichdidn't really work - make autoconf.mk depend on version_autogenerated.h to make sure to rebuild files as needed - add XECHO macro to allow for silent build using "make -s" Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121e: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MUNICes: fix board Makefile for remote build directoryWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12MPC5200: don't use hardcoded MBAR address in Bestcomm firmwareOliver Weber
Signed-off-by: Oliver Weber <almoeli@gmx.de>
2008-01-12Make bootretry work when command line editing is enabledAndreas Engel
Currently, when CONFIG_CMDLINE_EDITING is set, bootretry doesn't work. This patch fixes the problem. Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-01-12Refactor code for "i2c sdram" commandLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-12Fix "i2c sdram" command for DDR2 DIMMsLarry Johnson
Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the "i2c sdram" command. This patch provides correct alternative interpretations when DDR2 memory is detected. Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-12Fix linker scripts: add NOLOAD atribute to .bss/.sbss sectionsWolfgang Denk
With recent toolchain versions, some boards would not build because or errors like this one (here for ocotea board when building with ELDK 4.2 beta): ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab] For many boards, the .bss section is big enough that it wraps around at the end of the address space (0xFFFFFFFF), so the problem will not be visible unless you use a 64 bit tool chain for development. On some boards however, changes to the code size (due to different optimizations) we bail out with section overlaps like above. The fix is to add the NOLOAD attribute to the .bss and .sbss sections, telling the linker that .bss does not consume any space in the image. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12USB: Add Philips 1561 PCI-OHCI idsTsiChung Liew
(needed for M5475EVB) Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2008-01-12Add MAINTAINERS entries for ids8247, jupiter, municse, sc3 and uc101Wolfgang Denk
boards. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12MPC512X: Cleanup bus clock names.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12MPC512X: Fixed typo in macro name.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12ads5121: Added support for FDT.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12Coding Style cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12Fixed syntax error in function init_e300_core() of mpc83xx/start.S ifHeiko Schocher
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12MUNICes: Set the right CFG_DEFAULT_MBAR value.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12added the config File for the MUNICes board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12added basic support for the MUNICes board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Update CHANGELOG and MAINTAINERS files.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12Fix compilation problem in common/cmd_bmp.cAnatolij Gustschin
common/cmd_bmp.c fails to compile if CONFIG_VIDEO_BMP_GZIP isn't defined. This patch fix this. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-01-12Fix defaultconfig for the mgcoge board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Added support for the mgcoge board from keymile.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Enable SMC microcode relocation patch for SMC1.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
generated by cgit (git 2.34.1) at 2024-12-30 21:29:30 +0000