summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-02-21imx: mx7d: isolate resources to domain 0 for A7 corePeng Fan
In current design, if any peripheral was assigned to both A7 and M4, it will receive ipg_stop or ipg_wait when any of the 2 platforms enter low power mode. We will have a risk that, if A7 enter wait, M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait asserted same time. Also if M4 enters stop mode, A7 will have no chance to access the peripheral. There are 26 peripherals affected by this IC issue: SIM2(sim2/emvsim2) SIM1(sim1/emvsim1) UART1/UART2/UART3/UART4/UART5/UART6/UART7 SAI1/SAI2/SAI3 WDOG1/WDOG2/WDOG3/WDOG4 GPT1/GPT2/GPT3/GPT4 PWM1/PWM2/PWM3/PWM4 ENET1/ENET2 Software Workaround: The solution is to set the peripherals to Domain0 by A core, since A core in Domain0. The peripherals which will be used by M4, will be set to Domain1 by M4. For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will set WDOG4 to domain1, because M4 will use WDOG4. So the peripherals are not shared by them. This way requires the uboot implemented the RDC driver and set the 26 IPs above to domain 0 only. M4 image will set the M4 to domain 1 and set peripheral which it will use to domain 1. This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for i.MX7D SABRESD board, and setup the 26 IP resources to domain 0. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx7dsabresd: add command and macros for boot m4 corePeng Fan
Introduce macros and command to support booting M4 core for i.MX7D SabreSD board. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx7: implement functions to boot auxiliary corePeng Fan
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up. arch_auxiliary_core_check_up is used to check whether M4 is running or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will use the pc and stack which is set in arch_auxiliary_core_up to set R15 and R13 register and boot. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6sxsabresd: add command and macros for boot m4 corePeng Fan
Introduce macros and command to support booting M4 core for i.MX6SX SabreSD board. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6: implement functions to boot auxiliary corePeng Fan
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up. arch_auxiliary_core_check_up is used to check whether M4 is running or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will use the pc and stack which is set in arch_auxiliary_core_up to set R15 and R13 register and boot. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: imx-common: introduce boot auxiliary corePeng Fan
To boot a auxiliary core in asymmetric multicore system, introduce the new command "bootaux" to do it. Example of boot auxliary core from 0x70000000 where stores the boot head information that should be parsed by auxiliary core, "bootaux 0x70000000". Introduce Kconfig option IMX_BOOTAUX. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx7d: clock support for RDCPeng Fan
If CONFIG_IMX_RDC is enabled, enable clock for RDC and SEMAPHORE. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx7d: Add RDC supportPeng Fan
Add the peripherals/masters definitions and registers base addresses for mx7d RDC. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6sx Add RDC mappings of masters and peripheralsPeng Fan
Add the definitions for the RDC mappings for i.MX6 SoloX. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: imx-common: introduce Resource Domain Controller supportPeng Fan
Introduce Resource Domain Controller support for i.MX. Now i.MX6SX and i.MX7D supports this feature to assign masters and peripherals to different domains. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6: introduce rdc regsPeng Fan
Introudce rdc regs structure and rdc sema reg structure for i.MX6. For now, to i.MX6, only i.MX6SX supports this. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6quq7: add sd card detectionJulien CORJON
Add board_mmc_getcd function and declare CD_GPIO for SDCard. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
2016-02-21imx: mx6quq7: specify max_bus_witdh directly in usdhc_cfgJulien CORJON
Specify max_bus_width directly in usdhc_cfg static definition instead of tweaking it in the board_mmc_init() function. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
2016-02-21imx: mx6quq7: fix USDHC4 declarationJulien CORJON
USDHC2 does not exist on mx6quq7 board, as USDHC4 was already been declared this is probably a typo. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-02-21board: tbs2910: Autoselect environment device when booting from SDSoeren Moch
Implement board specific functions to select the environment device and partition when booting from SD/MMC. SD2: mmc 0 0 SD3: mmc 1 0 eMMC: mmc 2 1 Signed-off-by: Soeren Moch <smoch@web.de>
2016-02-21imx: mx6: Implement mmc_get_env_partSoeren Moch
commit 216d286c7e3d3d83d4d8ccaf0415192e1b1040c0 [imx: mx6: implement mmc_get_env_dev] introduced selection of the environment device according to the boot device when booting from SD/MMC. Extend this functionality for also selecting the device partition. Signed-off-by: Soeren Moch <smoch@web.de>
2016-02-21pinctrl: imx: Support i.MX7DPeng Fan
Introudce i.MX7 pinctrl driver support. For now only i.MX7D supported. There are two iomux controllers in i.MX7D, iomuxc and iomuxc_lpsr. To iomuxc_lpsr, ZERO_OFFSET_VALID is set, means offset of mux_reg and conf_reg can begin at 0. Signed-off-by: Peng Fan <van.freenix@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-21pinctrl: imx: Introduce pinctrl driver for i.MX6Peng Fan
Introduce pinctrl for i.MX6 1. pinctrl-imx.c is for common usage. It's used by i.MX6/7. 2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry. 3. To the pinctrl_ops implementation, only set_state is implemented. To i.MX6/7, the pinctrl dts entry is as following: &iomuxc { pinctrl-names = "default"; pinctrl_csi1: csi1grp { fsl,pins = < MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088 MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088 MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088 >; }; [.....] }; there is no property named function or groups. So pinctrl_generic_set_state can not be used here. 5. This driver is a simple implementation for i.mx iomux controller, only parse the fsl,pins property and write value to registers. 6. With DEBUG enabled, we can see log when "i2c bus 0": " set_state_simple op missing imx_pinctrl_set_state: i2c1grp mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f write mux: offset 0x14c val 0x10 select_input: offset 0x5d8 val 0x1 write config: offset 0x3bc val 0x7f mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f write mux: offset 0x148 val 0x10 select_input: offset 0x5d4 val 0x1 write config: offset 0x3b8 val 0x7f " this means imx6 pinctrl driver works as expected. Signed-off-by: Peng Fan <van.freenix@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-21imx: Refactoring CAAM Job Ring structure and Secure Memory for imx7Ulises Cardenas
Refactored data structure for CAAM's job ring and Secure Memory to support i.MX7. The new memory map use macros to resolve SM's offset by version. This will solve the versioning issue caused by the new version of secure memory of i.MX7 Signed-off-by: Ulises Cardenas <raul.casas@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-21mx7dsabresd: Make 'ums' command functionalFabio Estevam
When running the 'ums' command we get: => ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0xe18000 g_dnl_register: failed!, error: -22 ERROR: g_dnl_register failed at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage() Fix this by initializing USB OTG1 port as USB device mode instead of host. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21mx7dsabresd: Use Adrian's NXP email addressFabio Estevam
Use the new NXP email address for the board maintainer. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21mx6ul_14x14_evk: Select CONFIG_FSL_QSPIFabio Estevam
Select CONFIG_FSL_QSPI so that the SPI can be probed: => sf probe SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-02-21mxsboot: remove unused includeAndreas Bießmann
Commit 276d3ebb883024d753cd9c69ab2fd243ffa1262e removed htole32() but missed to remove the corresponding header. This is annoying, since BSD systems do not have endian.h. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Michael Heimpold <mhei@heimpold.de>
2016-02-04imx: mx6: implement board_mmc_get_env_devPeng Fan
Implement board_mmc_get_env_dev for the boards. Following is examples: SD1/SD2/SD3: return devno; SD2/SD3: return devno - 1; SD2/SD4: if (devno == 2), return dev - 2; return dev - 1; Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-04imx: mx6: implement mmc_get_env_devPeng Fan
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC. Introduce a weak function board_mmc_get_env_dev, different boards can implement it according to different sdhc controllers that used by the board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-04imx: mx7dsabresd: move mmc_get_env_devno to soc codePeng Fan
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to match the one in common/env_mmc.c. Introduce a weak function board_mmc_get_env_dev. Different boards can implement this according to sdhc controller which is used by the board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-02dm: vybrid_gpio: Drop legacy codeBhuvanchandra DV
All boards using this driver are with device tree support, hence drop the legacy code in driver to have a pure DT solution. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02dm: lpuart: Drop the legacy codeBhuvanchandra DV
All boards using this driver are with device tree support, hence drop the legacy code in driver to have a pure DT solution. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Drop enabling GPIO, SPI and UART in legacy modeBhuvanchandra DV
Remove the legacy way of enabling GPIO, SPI and UART on Vybrid based boards since these driver's now only supports DT mode. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Update defconfig'sBhuvanchandra DV
Let's go with pure DT solution for board's based on NXP/Freescale Vybrid platform. - Merge the DT defconfig with non-DT defconfig for Toradex Colibri VF50/VF61 and drop the non-DT defconfig. - Update the legacy defconfigs for NXP/Freescale VF610 Tower Board with DT. - Update the legacy defconfigs for Phytec phyCORE-vybrid Board with DT. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: pcm052: Add device tree file'sBhuvanchandra DV
- Add device tree files for Phytec phyCORE-Vybrid Board. - Enable lpuart support for Phytec phyCORE-Vybrid Board. - Use UART1 for stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vf610-twr: Add device tree file'sBhuvanchandra DV
- Add device tree files for NXP/Freescale VF610 Tower Board. - Enable lpuart support on NXP/Freescale VF610 Tower Board. - Use UART1 as stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: colibri-vf: Enable serial supportBhuvanchandra DV
- Enable lpuart support on Toradex Colibri VF50/VF61 - Use UART0 for stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Update the license stringBhuvanchandra DV
Since SPDX license is already there, drop the full one. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Enable lpuart supportBhuvanchandra DV
Add device tree node's for lpuart on Vybrid platform Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02imx: mx6sxsabresd: Add MCIMX28LCD display supportYe Li
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1 port, enable this display feature by adding relevant BSP codes and configurations. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02imx: mx6ul/sx: Fix issue in LCDIF clock dividers calculationYe Li
The checking with max frequency supported is not correct, because the temp is calculated by max pre and post dividers. We can decrease any divider to meet the max frequency limitation. Actually, the calculation below the codes is doing this way to find best pre and post dividers. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02imx: mx6sx: Fix issue in LCDIF clock enablementYe Li
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always enter the -EINVAL return. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02mx6slevk: Remove CONFIG_ETHPRIME optionFabio Estevam
As mx6slevk has only one Ethernet port, we don't need to declare CONFIG_ETHPRIME, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failureYe Li
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02tqma6_wru4: Fix the reset delay for the the LAN8720 PHYFabio Estevam
According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested by the LAN8720 datasheet. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02mx6slevk: Fix the reset delay for the the LAN8720 PHYFabio Estevam
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested in order to have Ethernet working again. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO boardYe Li
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02mx6: soc: Add ENET2 mac address supportYe Li
The i.MX6SX and i.MX6UL has two ENET controllers, add support for reading MAC address from fuse for ENET2. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02tools: mxsboot: Use more portable cpu_to_le32()Bin Meng
Currently when building mxsboot on certain machines it reports: HOSTCC tools/mxsboot tools/mxsboot.c: In function 'mx28_create_sd_image': tools/mxsboot.c:560: warning: implicit declaration of function 'htole32' /tmp/cchLIV6q.o: In function 'main': mxsboot.c:(.text+0x6d8): undefined reference to 'htole32' mxsboot.c:(.text+0x6e7): undefined reference to 'htole32' mxsboot.c:(.text+0x6f6): undefined reference to 'htole32' mxsboot.c:(.text+0x705): undefined reference to 'htole32' mxsboot.c:(.text+0x711): undefined reference to 'htole32' /tmp/cchLIV6q.o:mxsboot.c:(.text+0x71d): more undefined references to 'htole32' follow collect2: ld returned 1 exit status make[1]: *** [tools/mxsboot] Error 1 make: *** [tools] Error 2 The solution is to use cpu_to_le32() instead which is more portable, just like other U-Boot tools [1] do. [1] http://lists.denx.de/pipermail/u-boot/2014-October/192919.html Suggested-by: Marek Vasut <marex@denx.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-02-02wandboard: fix variable name so PXE boot worksPeter Robinson
All boards that support PXE booting use the pxefile_addr_r variable. Standardise wandboard with this variable as pxe_addr_r isn't used anywhere else so it's a typo. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02arm: imx6: Enable DDR calibration on NovenaMarek Vasut
Enable the DDR calibration functionality on Novena to deal with the memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM parameters so the calibration works properly. Signed-off-by: Marek Vasut <marex@denx.de>
2016-02-02arm: imx6: Add DDR3 calibration code for MX6 Q/D/DLMarek Vasut
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code fine-tunes the behavior of the MMDC controller in order to improve the signal integrity and memory stability. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2016-02-02Prepare v2016.03-rc1Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-02-02Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
generated by cgit (git 2.34.1) at 2024-12-28 13:04:21 +0000