| Age | Commit message (Collapse) | Author |
|---|
|
Add new fields "lanes, format & mode_flags" to structure
mipi_dsi_panel_plat.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Check the hardware version of DSI. Versions 1.30 & 1.31 are only
supported.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
|
|
Get below warning on ARM64 platform, because the bmp_load_addr
is defined to u32.
common/splash.c: In function ‘splash_video_logo_load’:
common/splash.c:74:9: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
74 | memcpy((void *)bmp_load_addr, bmp_logo_bitmap,
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # bpi-m1+, bpi-m64
|
|
Fix the bug that multiple lines wraps to overwrite logo bmp
display.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # bpi-m1+, bpi-m64
|
|
Update video bmp code so that we can display 8 bits logo on
24 or 32 bpp framebuffer.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # bpi-m1+, bpi-m64
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc6
Corrections for variable definitions are provided:
* Correct size of secure boot related UEFI variables.
* Do not use int for storing an enum.
* Replace fdt_addr by fdt_size where needed.
|
|
Since commit:
commit 6333cbb3817ed551cd7d4e92f7359c73ccc567fc
Author: Michael Walle <michael@walle.cc>
Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
, the clock output setting for the AR803x driver is removed from being
hardcoded in the PHY driver and should be passed via device tree instead.
Update the device tree with the "qca,clk-out-frequency" property so that
Ethernet can work again.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
|
|
The variables SetupMode, AuditMode, DeployedMode are explicitly defined as
UINT8 in the UEFI specification. The type of SecureBoot is UINT8 in EDK2.
Use variable name secure_boot instead of sec_boot for the value of the
UEFI variable SecureBoot.
Avoid abbreviations in function descriptions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Variable efi_secure_mode is meant to hold a value of enum efi_secure_mode.
So it should not be defined as int but as enum efi_secure_mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Variable fdt_size should be of type 'fdt_size_t', not 'fdt_addr_t'.
Fixes 0d7c2913fdf7: ("cmd: bootefi: Honor the address & size cells properties correctly")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
- Fix fsl_esdhc_imx tunning mask
- Disable CMD CRC for normal tuning for fsl_esdhc_imx
- Retry CM1 until emmc ready
- Fix sdhci HISPD handling
- Cache-aligned extcsd reading
|
|
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
|
|
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: fa33d207494c ("mmc: split fsl_esdhc driver for i.MX")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
|
|
The extcsd read target must be cache aligned in case the controller
uses DMA to read the extcsd register, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
- Assorted minor fixes
|
|
Avoid potential multiple definitions when CONFIG_ARM_PSCI_FW
is disabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch try to avoids eviction of dirty lines during DMA
transfer. The code right now execute the following step:
- allocate the buffer
- start a dma operation using the non-coherent dma buffer
- invalidate cache lines associated with the buffer
- read the buffer
This can lead to reading back not valid information, because the cache
controller could evict dirty cache lines belonging to the buffer *after*
the DMA operation has started to fill the DRAM.
In order to avoid this, a new invalidation is required *before* starting
the DMA operation. The patch just adds an invalidation before submitting
the DMA command.
Example below shows the nvme disk scan result without the following
patch
=> nvme scan
nvme_get_info_from_identify: nn = 544502629, vwc = 100,
sn = dev_0T, mn = `�\�, fr = t_part, mdts = 105
So, invalidating the cache before submitting the admin command,
fix the cpu read.
Cc: André Przywara <andre.przywara@arm.com>
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The correct name for the property is "qca,clk-out-frequency", so fix
it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
|
|
Commit 0528979fa7ab ("part: Drop disk_partition_t typedef") changed to
a struct. As a result it uncovered an apparent missing include in
zfs_common.h for part.h which actually contains the definition. The ZFS
handles the struct exclusively as pointers so it was only a warning.
warning: ‘struct disk_partition’ declared inside parameter list
will not be visible outside of this definition or declaration
void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info);
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Series-CC: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.07
-----------------
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/701059103
- Fixes for atheros and cubox
- Toradex: mostly environment
- i.MX7: DDR fixes
- switch to DM
- sabrelite : fix MMC access
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
After enabling SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC the MMC
initialization code is not longer needed.
This patch removes the unused code.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
|
|
In order to take the beneficts of DT and DM in SPL, like reusing the code
and avoid redundancy, enable SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC.
With this new configuration SPL image is 50 KB, higher than the
38 KB from the previous version, but it still under the 68 KB limit.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
|
|
In SPL legacy code only one MMC device is created, based on BOOT_CFG
register, which can be either SD or eMMC. In this context
board_boot_order return always MMC1 when configure to boot from
SD/eMMC. After switching to DM both SD and eMMC devices are created
based on the information available on DT, but as board_boot_order
only returns MMC1 is not possible to boot from eMMC.
This patch customizes board_boot_order taking into account BOOT_CFG
register to point to correct MMC1 / MMC2 device. Additionally, handle
IO mux for the desired boot device.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
|
|
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
|
|
Convert to DM_ETH to avoid board removal from the project.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Convert to DM_ETH to avoid board removal from the project.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Convert to DM_ETH to avoid board removal from the project.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
Since the i.MX8 GPIO banks are indexed from 0 not 1 on other i.MX
platforms, so we have to adjust the index accordingly.
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
We need to change the environment offset to avoid corrupting the U-Boot
binary when saving it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
This fixes the boot from USB loader, which is critical to easy the
manufacture process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
There are systems where board_early_init_f() is plain empty. Switch
the config option from "select" to "imply", to permit user to unset
the BOARD_EARLY_INIT_F if it were to be empty.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Update README to extract firmware from scripts
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
|
|
This is needed to obtain the MAC from EEPROM/OTP only after the final
env is populated, otherwise the ethaddr might be overriden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Harald Seiler <hws@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
It appears that MMC access on the Sabrelite has been broken since
cdcaee9518:
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment
Remove the board_mmc_init() and related entries now that we should be
using DM_MMC, add PINCTRL so that things work as expected.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
This introduces automatic boot counter that increases after every
reset.After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it's
disabled if bootlimit isn't set.
To enable this feature you have set bootcount limit ("bootlimit"),
alternate boot action ("altbootcmd") that will be performed if
the new value of bootcount exceeds the value of bootlimit, and
"upgrade_available" to let U-Boot automatically increase and save
the counter value after every reset:
> setenv bootlimit 5
> setenv upgrade_available 1
> setenv altbootcmd "bootm ..."
In case the bootlimit exceeds, the message will be shown and
albootcmd executed:
Warning: Bootlimit (5) exceeded. Using altbootcmd.
To reset bootcount run:
> bootcount reset
Print current value:
> bootcount print
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
s/fdt-module/fdt_module/g, as we don't use dash in fdt_file anymore.
Fixes: 4c63a601("apalis-tk1: support v1.2 hardware revision")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
