summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-03-12mmc:sdhci:fix: Change default interrupts enabled at SDHCI initializationŁukasz Majewski
This patch changes sdhci_init()'s behavior to NOT enable all interrupt sources by default. Moreover interrupt signaling has been disabled. This patch do not enable interrupts which aren't served in u-boot (they are defined at sdhci.h but NOT used elsewhere): - SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER, SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT Special care shall be put on SDHCI_INT_CARD_INT, which indicates interrupt generated by SD card. According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8 (Card Interrupt Status Enable) at "Normal Interrupt Status Enable Register" (offset 0x34) is set, the card interrupt detection is started. Then eMMC card may cause the SD controller to set this bit and then this interrupt is passed to booted OS and might cause kernel crash. To sum up: - Only enable interrupts, which are served at u-boot - This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at Linux kernel (versions 3.6+, sdhci controller) - Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS5: Snow: Add a configuration fileRajeshwari Shinde
This patch adds the configuration file for Snow Board and defines the same in boards.cfg. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS5: Add initial DTS file for Snow.Rajeshwari Shinde
This patch adds the DTS file for Snow Board. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: FDT: Add a H/W-trip member to TMU nodeAkshay Saraswat
This adds a member to TMU FDT node for providing hardware tripping temperature threshold. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add hardware trippingAkshay Saraswat
This adds hardware tripping at 110 degrees celsius which must enable forced system shutdown in case TMU fails to power off. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: Config: Enable dtt command for TMUAkshay Saraswat
This enables the dtt command to read the current SOC temperature with the help of TMU Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12TMU: Add TMU support in dtt commandAkshay Saraswat
Add generic TMU support alongwith i2c sensors in dtt command to enable temperature reading in cases where TMU is present along-with/instead-of i2c sensors. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: Config: Enable support for Exynos TMU driverAkshay Saraswat
Enables TMU driver support for exynos5250 Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add TMU init and status checkAkshay Saraswat
This adds call to tmu_init() and TMU boot time analysis for the SoC temperature threshold breach. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: FDT: Add TMU device node valuesAkshay Saraswat
Fdt entry for Exynos TMU driver specific pre-defined values used for calibration of current temperature and defining threshold values. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add driver for Thermal Management UnitAkshay Saraswat
Adding Exynos Thermal Management Unit driver to monitor SOC temperature and take actions corresponding to states of TMU. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12SMDK5250: FDT: Retrieve board model via DTRajeshwari Shinde
Print out the board model by parsing the device tree file. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS: Correct ordering of SPL machine_paramsSimon Glass
The mem_manuf is not in the correct order according to the string table. This causes cros_bundle_firmware to get the BL2 settings in the wrong order. This patch fixes the same. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-11env: Allow accessing non-mtd devicesLubomir Rintel
In certain cases, memory device is present as flat file or block device (via mmc or mtdblock layer). Do not attempt MTD operations against it. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2013-03-11cmd_df.c: Delete this clearly unused source file.Robert P. J. Day
Nothing appears to use or compile cmd_df.c anymore. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11cmd_mtdparts.c: Correct "reseting" to "resetting" in error msgsRobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11Allow u-boot to be silent without forcing Linux to beJoe Hershberger
That's a bit presumptuous of you, u-boot! Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-11Fix a couple typoes in tools/env/READMERobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11tools: update checkpatch to latest upstream versionKim Phillips
i.e., from the linux kernel's commit be987d9f80354e2e919926349282facd74992f90 Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-03-11tools: enable more checkpatch tests by defaultKim Phillips
without this, patches don't get checked for proper alignment, and e.g., for spaces after a cast and/or before a semicolon. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-03-11cmd_part: don't print cmd name twice in helpStephen Warren
The core implementation of "help" already prints the command name before the help text of a specific command. Remove it from part's own help text to avoid it being printed twice: Tegra114 (Dalmore) # help part part - disk partition related commands Usage: part part uuid <interface> <dev>:<part> - print partition UUID ... Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-03-11MAKEALL: fix kill_children for BSD hostsAndreas Bießmann
ps on BSD hosts (like OS X) do not provide the --no-headers switch nor understand the AIX format descriptions. Unfortunately there seems no solution to get the PIDs of children in a platfrom independent manner. Therefore detect the OS and decide upon that which way to go. This patch makes the MAKEALL script cleanly stoppable on bare OS X when using the parallel builds of targets. Additionally this patch removes double call to grep by a single call to sed for GNU style child PID detection. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-11mvsata_ide.c: Correction of typo in commentsGray Remlin
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
2013-03-11ppc: Remove PCIPPC2 and PCIPPC6 boardsStefan Roese
These boards seem to be unmaintained for quite some time. So lets remove support for them completely. This also cleans up some common drivers/files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch> Acked-by: Wolfgang Denk <wd@denx.de>
2013-03-11display_options:print_buffer: align ASCII printAndreas Bießmann
This patch adds whitespace to the printed hex numbers to have an aligned ASCII printout at the end of the line. This changes for example the md output from: ---8<--- OMAP3 Tricorder # md.l $loadaddr 5 82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........ 82000010: 01010000 .... --->8--- to ---8<--- OMAP3 Tricorder # md.l $loadaddr 5 82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........ 82000010: 01010000 .... --->8--- The cost of this is about 72 byte .text increase (tested with at91 build). Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-11Feature Removal: disable "mtest" command by defaultWolfgang Denk
The "mtest" command is of little practical use (if any), and experience has shown that a large number of board configurations define useless or even dangerous start and end addresses. If not even the board maintainers are able to figure out which memory range can be reliably tested, how can we expect such from the end users? As this problem comes up repeatedly, we rather do not enable this command by default, so only people who know what they are doing will be confronted with it. As this changes the user interface, we allow for a grace period before this change takes effect. For now, we make "mtest" configurable through the CONFIG_CMD_MEMTEST variable, which is defined in include/config_cmd_default.h; we also add an entry to doc/feature-removal-schedule.txt which announces the removal of this default setting in two releases from now, i. e. with v2013.07. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com>
2013-03-11Merge u-boot/master into u-boot-ti/masterTom Rini
In master we had already taken a patch to fix the davinci GPIO code for CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these conflicts manually and comment the #else/#endif lines for clarity. Conflicts: arch/arm/include/asm/arch-davinci/gpio.h drivers/gpio/da8xx_gpio.c Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add silicon id support for DRA752 socLokesh Vutla
Adding CPU detection support for the DRA752 ES1.0 soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add dra7xx_evm build supportLokesh Vutla
Adding the build support for dra7xx_evm. Reusing omap5_evm.h config by moving it to omap5_common.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11arm: dra7xx: Add board files for DRA7XX socsLokesh Vutla
Adding new board files for DRA7XX socs. The pad registers layout is changed completely from OMAP5 So introducing the new structure here and also adding the minimal data. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt omap_mmc_init call for last 2 params] Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add DDR related data for DRA752 ES1.0Lokesh Vutla
DRA752 uses DDR3. Populating the corresponding structures with DDR3 data. Writing into MA registers if only MA is present in that soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add control module changesLokesh Vutla
Control module register addresses are changed from OMAP5 to DRA7XX socs. So adding the necessary changes for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: clock: Add the dplls dataLokesh Vutla
A new DPLL DDR is added in DRA7XX socs. Now clocks to EMIF CD is from DPLL DDR. So DPLL DDR should be locked before initializing RAM. Also adding other dpll data which are different from OMAP5 ES2.0. SYS_CLK running at 20MHz is introduced in DRA7xx socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: clock: Add the prcm changesLokesh Vutla
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX. So adding the necessary register changes for DRA7XX socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11ARM: OMAP5: srcomp: enable slew rate compensation cells after powerupLokesh Vutla
After power-up SRCOMP cells are by-passed by default in OMAP5. Software has to enable these SRCOMP sells. For ES2: All 5 SRCOMP cells needs to be enabled. For ES1: Only 4 SRCOMP cells in core power domain are enabled. The 1 in wkup domain is not enabled because smart i/os of wkup domain work with default compensation code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP5: Add DDR changes required for OMAP543X ES2.0 SOCsLokesh Vutla
Add pre calculated timing settings of LPDDR2 and DDR3 memories present in OMAP5430 and OMAP5432 ES2.0 versions. Also adding the DDR pad io settings required for OMAP543X SOCs here. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendumSRICHARAN R
Change OPP settings as per the latest 0.5 version of addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched here to add dummy dividers. While here correcting OPP_NOM mpu, core frequency for OMAP4430 ES2.x Note that OMAP5430 ES1.0 support is still kept alive and would be removed in a cleanup later. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
2013-03-11ARM: OMAP5: clock: Add the prcm register changes required for ES2.0SRICHARAN R
PRCM register addresses are changed from ES1.0 to ES2.0 due to PER power domain getting moved to CORE power domain. So adding the nessecary register changes for the same. Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP5: Add silicon id support for ES2.0 revision.SRICHARAN R
Adding the CPU detection suport for OMAP5430 and OMAP5432 ES2.0 SOCs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
2013-03-11ARM: OMAP5: Clean up iosettings codeLokesh Vutla
There is some code duplication in the ddr io settings code. This is avoided by moving the data to a Soc specific place and letting the code generic. This avoids unnessecary code addition for future socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Make control module register structure genericLokesh Vutla
A seperate omap_sys_ctrl_regs structure is defined for omap4 & 5. If there is any change in control module for any of the ES versions, a new structure needs to be created. In order to remove this dependency, making the register structure generic for all the omap4+ boards. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Cleanup emif specific filesLokesh Vutla
Removing the duplicated code in ddr3 initialization. Also creating structure for lpddr2 mode registers to avoid unnessecary revision checks. These change reduces code addition for future Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Clean up the pmic codeSRICHARAN R
The pmic code is duplicated for OMAP 4 and 5. Instead move the data to Soc specific place and share the code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Cleanup the clocks layerSRICHARAN R
Currently there is quite a lot of code which is duplicated in the clocks code for OMAP 4 and 5 Socs. Avoiding this here by moving the clocks data to a SOC specific place and the sharing the common code. This helps in addition of a new Soc with minimal changes. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Change the PRCM structure prototype common for all SocsSRICHARAN R
The current PRCM structure prototype directly matches the hardware register layout. So there is a need to change this for every new silicon revision which has register space changes. Avoiding this by making the prototye generic and populating the register addresses seperately for all Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11ARM: OMAP4+: emif: Detect SDRAM from SDRAM config registerLokesh Vutla
Now SDRAM initialization is done on the basis of omap revision. Instead this should be done on basis of SDRAM type read from EMIF_SDRAM_CONFIG register. This will be helpful to avoid unnessecary cpu checks for new boards Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11cm_t35: prevent splashimage from being set to a bad valueNikita Kiryanov
Define CONFIG_SPLASHIMAGE_GUARD to prevent splashimage from being set to a value that will cause U-Boot to hang while displaying a splash screen. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-11lcd: implement a callback for splashimageNikita Kiryanov
On some architectures certain values of splashimage will lead to a data abort exception. Document the problem, and implement a callback for splashimage to reject such values. Cc: Anatolij Gustschin <agust@denx.de> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-11am335x: cpsw: optimize cpsw_send to increase network performanceMugunthan V N
Before submitting packets to cpdma, phy status is updated on every packet which leads to delay in packet send intern reduces the Ethernet performance. Checking mdio status for each packet will reduce timetaken to send a packet and there by increasing the Ethernet performance. With this the performance is increased from 208KiB/s to 375KiB/s on EVMsk Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-03-11omap4_common: Enable CONFIG_CMD_BOOTZTom Rini
With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: R Sricharan <r.sricharan@ti.com>
generated by cgit (git 2.34.1) at 2025-02-12 18:11:07 +0000