summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-08-03configs: pico-imx6: convert ethernet function to DM_ETHWig Cheng
Before enable _DM_ETH: Net: FEC [PRIME] After enable DM_ETH: Net: eth0: ethernet@2188000 Here is the test commands: => dhcp BOOTP broadcast 1 DHCP client bound to address 10.88.88.152 (146 ms) *** ERROR: `serverip' not set Cannot autoload with TFTPGET => ping 8.8.8.8 Using ethernet@2188000 device host 8.8.8.8 is alive Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
2020-08-03imx8m: enlarge CONFIG_SYS_BOOTM_LENPeng Fan
Enlarge CONFIG_SYS_BOOTM_LEN when booting FIT image with AArch32 mode Linux kernel. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-08-03arm: imx6q: pcm058: Rework SPI NOR configurationNiel Fourie
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR, modify the offset of U-boot proper in the SPI NOR, so the difference in offset matches between SPL and U-boot matches that of the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI NOR at an offset of 0x400. Update the README to reflect this change. Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-08-03ARM: imx: hab: panic on authentication failureMarek Vasut
Instead of hang()ing the system and thus disallowing any automated recovery possibility from a HAB authentication failure, panic() . The panic() function can be configured to hang() the system after printing an error message, however the default is to reset the system instead. This allows redundant boot to work correctly. In case the primary or secondary image cannot be authenticated, the system reboots and bootrom can try to start the other one. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-08-03imx: Add MYiR Tech MYS-6ULX supportParthiban Nallathambi
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based on imx6ULL SoC from NXP and provision for expansion board. This commit adds support only for SBC with NAND. CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C) at 45C Reset cause: WDOG Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND Board: MYiR MYS-6ULX 6ULL Single Board Computer DRAM: 256 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 In: serial@2020000 Out: serial@2020000 Err: serial@2020000 Net: FEC0 Working: - Eth0 - MMC/SD - NAND - UART 1 - USB host Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
2020-08-02mx6cuboxi: enable OF_PLATDATAWalter Lozano
As both MMC and GPIO driver now supports OF_PLATDATA, enable it in defconfig in order to reduce the SPL footprint. After applying this setting the SPL reduction is 5 KB, which partially compensates the increment due to DM. Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-02drivers: rename more drivers to match compatible stringWalter Lozano
Continuing with the approach in commit <addf358bac1d2bd0> rename additional drivers to allow the OF_PLATDATA support. Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-02mmc: fsl_esdhc_imx: add CD support when OF_PLATDATA is enabledWalter Lozano
After enabling OF_PLATDATA support to both MMC and GPIO drivers add the support for card detection. Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-02gpio: mxc_gpio: add OF_PLATDATA supportWalter Lozano
Continuing with the OF_PLATADATA support for iMX6 to reduce SPL footprint, add it to mxc_gpio. Thanks to this, it will be possible to enable card detection on MMC driver. Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-08-02mmc: fsl_esdhc_imx: add OF_PLATDATA supportWalter Lozano
In order to reduce the footprint of SPL by removing dtb and library overhead, add OF_PLATDATA support to fsl_esdhc_imx. This initial approach does not support card detection, which will be enabled after adding OF_PLATDATA support to GPIO. Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-02mmc: fsl_esdhc_imx: rename driver name to match ll_entryWalter Lozano
As discussed in commit <addf358bac1d2bd0> rename fsl_esdhc_imx driver to allow the OF_PLATDATA support. Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-27dm: Fix build error when OF_CONTROL is not setDan Murphy
With OF_CONTROL disabled the build fails for include/dm/read.h:932:10: error: ‘ENOTSUPP’ undeclared (first use in this function) 932 | return -ENOTSUPP; Fixes: 45224e8f2691 ("dm: core: gracefully handle alias seq without of") Signed-off-by: Dan Murphy <dmurphy@ti.com>
2020-07-27imx8m: soc: Remove unneeded spaceFabio Estevam
Checkpatch reports the following issue: ERROR: space prohibited before that ',' (ctx:WxW) #936: FILE: arch/arm/mach-imx/imx8m/soc.c:936: + 0, 0 , 0, 0, 0, 0, &res); Remove the unneeded space. ^ Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-07-27imx8m: ddrphy_utils: Improve coding styleFabio Estevam
Currently checkpatch is not happy about this file: total: 14 errors, 2 warnings, 7 checks, 359 lines checked Improve the coding style so that it can now report: total: 0 errors, 0 warnings, 6 checks, 360 lines checked Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-07-27colibri-imx7: fix splash logo drawingIgor Opaniuk
1. Configure white on black for video console. 2. Enable printing bmp logo during late board init stage. 3. Use iomux configuration from device tree. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27colibri-imx6ull: fix splash screen logo drawingIgor Opaniuk
Configure white on black for video console. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27colibri-imx6ull: show boot logoIgor Opaniuk
1. Show boot logo embed in U-Boot blob. 2. Drop iomux configration for LCD, and use the one provided in device tree. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27ARM: dts: imx7-colibri: multiple node updatesIgor Opaniuk
1. Move u-boot specific nodes to u-boot dts include: legacy lcdif node and aliases. 2. Add iomux configuration for LCD. 3. Drop un-needed u-boot,dm-pre-reloc for alias node. 4. Fix display-timings, use the one from Toradex downstream kernel [1] [1]: https://git.toradex.com/cgit/linux-toradex.git/tree/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi?h=toradex_4.9-2.3.x-imx#n206 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: common: show boot logoIgor Opaniuk
Add function for showing boot logo, embed into u-boot blob. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27ARM: dts: imx6ull-colibri: move u-boot specific nodeIgor Opaniuk
1. Move aliases and legacy lcdif node to the u-boot specific dts include. 2. Provide proper display timings, as in the downstream Toradex kernel [1]. [1]: https://git.toradex.com/cgit/linux-toradex.git/tree/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi?h=toradex_4.9-2.3.x-imx#n183 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27verdin-imx8mm: add EEPROM support for carrier boardIgor Opaniuk
Enable these Kconfig symbols: TDX_CFG_BLOCK_EXTRA=y TDX_HAVE_EEPROM_EXTRA=y Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27ARM: dts: imx8mm-verdin: eeprom nodes adjustmentsIgor Opaniuk
Rename EEPROM nodes. Create aliases for EEPROM to unify their order: eeprom0 - on-module EEPROM eeprom1 - carrier-board EEPROM eeprom2 - MIPI-DSI to HDMI adapter EEPROM Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: tdx-cfg-block: add carrier board info printingIgor Opaniuk
Add carrier board info printing during boot time: U-Boot 2020.07-rc4-02435-g1756e05 (Jun 22 2020 - 22:43:59 +0300) CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz .... Carrier: Toradex Verdin Development Board V1.0A, Serial# 10622780 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: tdx-cfg-clock: add migration routine from PID8Igor Opaniuk
Add migration routine from PID8 pre-stored values on EEPROM (including sane value checks). Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: tdx-cfg-block: add support for EEPROMIgor Opaniuk
This introduces support for EEPROM as a storage for the main Toradex config block and additional config blocks on extra EEPROM chips (on carrier board or video adapters). To enable EEPROM as a storage for the main config block: TDX_HAVE_EEPROM=y. For additional EEPROMs please enable this Kconfig symbol: TDX_CFG_BLOCK_EXTRA=y. Information about existing EEPROM chips is provided via Device Tree using aliases. You can also write configuration for the carrier board using create_carrier subcommand for cfgblock. Example: Verdin iMX8MM # cfgblock create_carrier Supported carrier boards: UNKNOWN CARRIER = [0] Verdin Carrier Board = [1] Choose your carrier board (provide ID): 1 Enter carrier board version (e.g. V1.1B): V1.0A Enter carrier board serial number: 10622780 Also with barcode: Verdin iMX8MM # cfgblock create carrier -y 0156100010622780 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: tdx-cfg-block: add carrier boards and display adaptersIgor Opaniuk
Add defines for supported carrier boards and display adapters. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27toradex: tdx-cfg-block: add EEPROM read/store wrappersIgor Opaniuk
These functions wrap functionality for storing config blocks in EEPROM. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27imx: mx7: fix DDRC size in A7-M4 mapping tableIgor Opaniuk
According to i.MX 7Solo Applications Processor Reference Manual, 2.1.3 Cortex-M4 Memory Map, M4 can address only 1536MB of DDRC (Start Address: 0x8000_0000; End Address: 0xDFFF_FFFF). Correct DDRC size to 0x60000000. Fixes: c0f037f6("mach-imx: bootaux: elf firmware support") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-24Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fix SiFive HiFive Unleashed board booting failure problem. - Enable SiFive fu540 PWM driver. - Support SiFive fu540: SPI boot. - Update OpenSBI used for RISC-V CI testing. - Revert "riscv: Allow use of reset drivers". - Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"". - sysreset: syscon: - Don't assume default value for offset and mask property. - Support value property. - qemu: Add syscon reboot and poweroff support. - Fix SIFIVE debug serial dependency. - Fix linking error when building u-boot-spl with no SMP support. - AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg. - Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi - SiFive fu540 avoid using hardcoded ram base and size.
2020-07-24Revert "Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dm"Tom Rini
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing changes made to 56d37f1c564107e27d873181d838571b7d7860e7. Unfortunately this is causing CI failures: https://travis-ci.org/github/trini/u-boot/jobs/711313649 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24ram: sifive: Avoid using hardcoded ram base and sizeBin Meng
At present the SiFive FU540 RAM driver uses hard-coded memory base address and size to initialize the DDR controller. This may not be true when this driver is used on another board based on FU540. Update the driver to read the memory information from DT and use that during the initialization. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Leo Liang <ycliang@andestech.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24riscv: dts: hifive-unleashed-a00: Make memory node available to SPLBin Meng
Make memory node available to SPL in prepration to updates to SiFive DDR RAM driver to read memory information from DT. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24riscv: ae350: Use fdtdec_get_addr_size_auto_noparent to parse smc regRick Chen
Use fdtdec_get_addr_size_auto_noparent to read the "reg" property instead of fdtdec_get_addr. This will increase the compatibility of dtb parsing. Signed-off-by: Rick Chen <rick@andestech.com> Acked-by: Leo Liang <ycliang@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Leo Liang <ycliang@andestech.com>
2020-07-24riscv: Fix linking error when building u-boot-spl with no SMP supportLeo Yu-Chi Liang
Switch off SMP support when building u-boot-spl would cause linking error as follow: undefined reference to 'secondary hart relocate' and 'smp_call_function'. Add macro to wrap up proper code region that needs SMP configuration on. Signed-off by: Leo Liang <ycliang@andestech.com> Cc: rick@andestech.com Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24serial: Fix SIFIVE debug serial dependencyMichal Simek
The commit 4cc24aeaf420 ("serial: Add missing Kconfig dependencies for debug consoles") has added incorrect dependency for SIFIVE debug uart which should depend on SIFIVE driver instead of PL01x. Fixes: 4cc24aeaf420 ("serial: Add missing Kconfig dependencies for debug consoles") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Leo Liang <ycliang@andestech.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
2020-07-24riscv: qemu: Add syscon reboot and poweroff supportBin Meng
This adds syscon reboot and poweroff support to QEMU RISC-V. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24sysreset: syscon: Support value propertyBin Meng
Per the DT binding, <mask> and <value> property can have either one or both, and if <value> is missing, <mask> should be used, which is what current U-Boot sysreset_syscon driver supports. This adds support to the <value> property to the driver, and <mask> semantics is updated to really be a mask to the value if both exist. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24sysreset: syscon: Don't assume default value for offset and mask propertyBin Meng
Per the DT binding, <offset> is a required property. Let's abort the probe if it is missing. For the <mask> property, current codes assume a default value of zero, which is not correct either. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-07-24Revert "Revert "riscv: sifive: fu540: Add gpio-restart support""Bin Meng
This reverts commit 23da3c682a84a2ad67a67287979dd4f5259ff607. Now the build failure of sifive_fu540_defconfig board has been fixed, revert this "revert patch". Signed-off-by: Bin Meng <bin.meng@windriver.com>
2020-07-24Revert "riscv: Allow use of reset drivers"Bin Meng
This reverts commit 958a3f464c7f8ef7e10db9feb663e9e80445ce2f. A more appropriate change below is already in mainline. Commit fd31e4fd184f ("riscv: Do not build reset.c if SYSRESET is on") Revert this patch, so that U-Boot can be built successfully for SiFive Fu540 board. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Liang <ycliang@andestech.com>
2020-07-24azure: gitlab: travis: Update OpenSBI used for RISC-V testingBin Meng
Change to use OpenSBI release v0.8 generic platform images for QEMU RISC-V CI testing for azure, gitlab and travis-ci. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-07-24sifive: fu540: Enable SF distro bootcmdJagan Teki
Enable SPI flash(SF) distro boot command in Sifive FU540. This distro boot will read the boot script at specific location at the flash and start sourcing the same. Included the SF device at the last of the target devices list since all the rest of the devices on the list have more possibility to boot the distribution due to the size of the SPI flash is concern. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24sifive: fu540: Add boot flash script offset, sizeJagan Teki
HiFive-Unleashed-A00 has SPI flash with 32MiB size. So, let's use the script offset at the end of 4K. This way it cannot overlap any offsets being used by software components in flash layout. So, SF distrocmd will pick the script at desired script address and run. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24sifive: fu540: Mark the default env as SPI flashJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24env: Enable SPI flash env for SiFive FU540Jagan Teki
SPI flash device on HiFive Unleashed has 32MiB Size. This patch adds SPI flash environment after U-Boot proper partition with a size of 128KiB. SPI flash partition layout(32MiB): 0 - 34 : reserved for GPT header 35 - 39 : unused 40 - 2087 : loader1 (SPL, FSBL) 2088 - 10279 : loader2 (U-Boot proper, U-Boot) 10280 - 10535 : environment 10536 - 65494 : rootfs 65528 - 65536 : distro script Note: the loader1 must start from 40th sector even though there are 6 free sectors prior since 40th sector is nearest flash sector boundary.  Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24sifive: fu540: Add Booting from SPIJagan Teki
Add booting from SPI for SiFive Unleashed board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24sifive: fu540: Add runtime boot mode detectionJagan Teki
Add support to detect boot mode at runtime for SiFive FU540 boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-24riscv: sifive: fu540: Enable SiFive PWM driverPragnesh Patel
This patch enables SiFive PWM driver for the SiFive Unleashed board. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bin.meng@windriver.com>
2020-07-24riscv: Make SiFive HiFive Unleashed board boot againBin Meng
Commit 40686c394e53 ("riscv: Clean up IPI initialization code") caused U-Boot failed to boot on SiFive HiFive Unleashed board. The codes inside arch_cpu_init_dm() may call U-Boot timer APIs before the call to riscv_init_ipi(). At that time the timer register base (e.g.: the SiFive CLINT device in this case) is unknown yet. It might be the name riscv_init_ipi() that misleads people to only consider it is related to IPI, but in fact the timer capability is provided by the same SiFive CLINT device that provides the IPI. Timer capability is needed for both UP and SMP. Considering that the original refactor does have benefits, that it makes the IPI code more similar to U-Boot initialization idioms. It also removes some quite ugly macros. Let's do the minimal revert instead of a complete revert, plus a fixes to arch_cpu_init_dm() to consider the SPL case. Fixes: 40686c394e53 ("riscv: Clean up IPI initialization code") Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Tested-by: Leo Liang <ycliang@andestech.com>
2020-07-23Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dmTom Rini
binman support for FIT new UCLASS_SOC patman switch 'test' command minor fdt fixes patman usability improvements
generated by cgit (git 2.34.1) at 2025-01-25 11:26:30 +0000