summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-03-13beagle_x15: increase phy autoneg timeoutSekhar Nori
When Beagle X15 is connected to Gigabit switch, it takes more time to finish auto-negotiation than on a 10/100 switch. The default 4 second limit times-out more often than not. This is observed when testing with a D-Link DGS-1008A desktop switch. Increase the auto-negotiation time-out for Beagle-X15 to handle this case. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: rx51: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon
RX51 has a secure logic which uses different parameters compared to traditional implementation. So, make the generic secure acr write over-ride-able by board file and refactor rx51 code to use this. While at it, enable the OMAP3 specific errata code for 454179, 430973, 621766. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon
Enable the OMAP3 specific errata code for 454179, 430973, 621766 and while at it, remove legacy non-revision checked errata logic. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP5 / DRA7: Setup L2 Aux Control Register with recommended configurationNishanth Menon
Update to existing recommendation for L2ACTLR configuration to prevent system instability and optimize performance. These apply to both OMAP5 and DRA7. Reported-by: Vivek Chengalvala <vchengalvala@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: DRA7 / OMAP5: Add workaround for ARM errata 798870Praveen Rao
This patch enables the workaround for ARM errata 798870 for OMAP5 / DRA7 which says "If back-to-back speculative cache line fills (fill A and fill B) are issued from the L1 data cache of a CPU to the L2 cache, the second request (fill B) is then cancelled, and the second request would have detected a hazard against a recent write or eviction (write B) to the same cache line as fill B then the L2 logic might deadlock." An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced here as well. Signed-off-by: Praveen Rao <prao@ti.com> Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1Nishanth Menon
omap_smc1 is now generic enough to remove duplicate omap3_gp_romcode_call logic that omap3 introduced. As part of this change, move to using the generic lowlevel_init.S for omap3 as well. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: Rename omap3.h to omap.h to be generic as all SoCsNishanth Menon
This is in preperation of using generic cross OMAP code. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP: Change set_pl310_ctrl_reg to be genericNishanth Menon
set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup PL310 control register, however, that is something that is generic enough to be used for OMAP5 generation of processors as well. The only difference being the service being invoked for the function. So, convert the service to a macro and use a generic name (same as that used in Linux for some consistency). While at that, also add a data barrier which is necessary as per recommendation. While at this, smc #0 is maintained as handcoded assembly thanks to various gcc version eccentricities, discussion thread: http://marc.info/?t=142542166800001&r=1&w=2 Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: Introduce erratum workaround for 621766Nishanth Menon
621766: Under a specific set of conditions, executing a sequence of NEON or vfp load instructions can cause processor deadlock Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set L1NEON to 1 Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: Introduce erratum workaround for 430973Nishanth Menon
430973: Stale prediction on replaced inter working branch causes Cortex-A8 to execute in the wrong ARM/Thumb state Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set IBE to 1 Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: Introduce erratum workaround for 454179Nishanth Menon
454179: Stale prediction may inhibit target address misprediction on next predicted taken branch Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set IBE and disable branch size mispredict to 1 Also provide a hook for SoC specific handling to take place if needed. Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: Introduce erratum workaround for 798870Nishanth Menon
Add workaround for Cortex-A15 ARM erratum 798870 which says "If back-to-back speculative cache line fills (fill A and fill B) are issued from the L1 data cache of a CPU to the L2 cache, the second request (fill B) is then cancelled, and the second request would have detected a hazard against a recent write or eviction (write B) to the same cache line as fill B then the L2 logic might deadlock." Implementations for SoC families such as Exynos, OMAP5/DRA7 etc will be widely different. Every SoC has slightly different manner of setting up access to L2ACLR and similar registers since the Secure Monitor handling of Secure Monitor Call(smc) is diverse. Hence an weak function is introduced which may be overriden to implement SoC specific accessor implementation. Based on ARM errata Document revision 18.0 (22 Nov 2013) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13am335x_evm_usbspl: Remove other SPL modesTom Rini
The purpose of this build target is to do SPL over USB RNDIS. We remove YMODEM, MMC and NAND (and re-set ENV to be built-in) as when those are needed we can use the other build targets. This brings us well under size limit again. Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-13mx6sabre: Do not enable UMS with SPLFabio Estevam
Since commit ad8aae82b20ac6a ("mx6sabre: Enable User Mass Storage") SPL target does not boot anymore due to the increased spl image size. Only enable USB Mass Storage for the non-SPL target. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13warp: Select CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODEFabio Estevam
Warp has a DDR eMMC, so enable CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE for better performance: reading zImage 5790288 bytes read in 117 ms (47.2 MiB/s) Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-03-13mx6_common: Do not select esdhc DDR mode for all boardsFabio Estevam
CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE should be selected only by boards that really have a DDR-capable eMMC, so remove this option from common code to avoid regressions. Reported-by: Stefan Roese <sr@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com> Tested-by: Stefan Roese <sr@denx.de>
2015-03-13mx53ard: Use the standard U-boot promptFabio Estevam
By not defining CONFIG_SYS_PROMPT, the standard "=>" prompt is used, so remove its definition. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-13common/board_f.c: Enable IMX watchdog in init_func_watchdog_init()Stefan Roese
Without this patch, the IMX watchdog will not be initialized. And therefor not active. This patch fixes this by calling hw_watchdog_init() also when CONFIG_IMX_WATCHDOG is defined. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2015-03-13mx6: soc: Switch to cold resetDirk Behme
Disable the warm reset and enable the cold reset for a more reliable restart ('reset'). This is taken from the Linux kernel, see imx_src_init() in arch/arm/mach-imx/src.c. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
2015-03-13imx:mx6 remove duplicated includesPeng Fan
There is no need to include asm/bootm.h twice, so remove one. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-03-13mx6sabre_common.h: remove deprecated mmc open/closemaxin.john@enea.com
Replace "mmc open/close" with "mmc dev" in mx6sabre_common.h as those commands were removed with this commit: 614b2bf1c9bf80dbad24f5e5ce1d115bf24a831d cmd_mmc.c: Drop open/close mmc sub-commands Signed-off-by: Maxin B. John <maxin.john@enea.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-03-13warp: Add a README fileFabio Estevam
Provide instructions on how to upgrade U-boot in the eMMC. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-03-13warp: Add Device Firmware Upgrade supportFabio Estevam
Device Firmware Upgrade (DFU) is a very convenient mechanism to upgrade U-boot on the eMMC. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-03-13novena: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2015-03-13warp: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-03-13nitrogen6x: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-13hummingboard: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-13wandboard: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-13mxs: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2015-03-13mx25pdk: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-13mx31pdk: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
2015-03-13mx35pdk: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2015-03-13mx51evk: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2015-03-13mx53loco: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2015-03-13mx6qarm2: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2015-03-13mx6slevk: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2015-03-13mx6sxsabresd: Use the default CONFIG_SYS_PBSIZEFabio Estevam
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into the console and hitting enter afterwards, causes a hang in the system because CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error message: "Unknown command '' - try 'help'". Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve this problem. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-10Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
Conflicts: README Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-10sunxi: video: Fix VIDEO_LCD_PANEL_I2C being enabled by defaultHans de Goede
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be enabled on all sunxi boards. Also fix a compile error which shows up once VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sunxi: Add Wexler TAB7200 supportAleksei Mamlin
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: Ippo_q8h defconfigs: Enable otg vbus detection using AXP223 PMICChen-Yu Tsai
Use the AXP223 PMIC to detect VBUS for musb otg support. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: musb: Support checking VBUS using AXP221 PMICChen-Yu Tsai
This enables the musb glue layer to use the AXP221's VBUS detection function to check for VBUS. This fixes otg support on the A23 q8h tablets. Note that u-boot never calls musb_shutdown(), so once VBUS is enabled, it is never disabled until the system is powered off, or the OS does so. This can be used to our advantage to keep VBUS powered into the OS, where support for AXP221 is not available yet. Fixes: 52defe8f6570 ("sunxi: musb: Check Vbus-det before enabling otg port power") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: axp221: Add VBUS detection supportChen-Yu Tsai
Some of the AXP PMICs support VBUS detection, i.e. checking whether VBUS power input is available and usable (supplied by an external source). A few boards use this instead of a separate GPIO to detect VBUS on USB OTG. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sun7i: Add support for the Orange Pi Mini boardHans de Goede
The Orange Pi Mini is an A20 based development board featuring 1G RAM, HDMI, 1Gbit ethernet, USB wifi, SATA, 2 sdcard slots (use the top one for booting), 2 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V. Also see: http://www.orangepi.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun7i: Add support for the Orange Pi boardHans de Goede
The Orange Pi is an A20 based development board featuring 1G RAM, HDMI & VGA, 1Gbit ethernet, USB wifi, SATA, 4 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V. Also see: http://www.orangepi.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun7i: Add support for the Wits Pro A20 DKT boardHans de Goede
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND, sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen and a ton of IO connectors. Note there seem to be multiple sdcard slots on the board (4 in total), but other then mmc0 none of these are hooked up by default, there is a ton of dip-switches which likely allow hooking some of these up, but the documentation of the board only describes the use of a fraction of them, so for now we only support mmc0. Also see: http://www.merrii.com/en/pla_d.asp?id=163 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sunxi: Add support for the Forfun Q88DB tabletJens Lucius
The Forfun Q88DB is an A13 tablet in the common Q8 format. Features are 512MB RAM, 4GB NAND, 7" Display, RTL8188 Wifi, 2 cameras. For more details see: http://linux-sunxi.org/Forfun_Q88DB Signed-off-by: Jens Lucius <info@jenslucius.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun6i: Add support for the Mele I7 boardMarcus Cooper
The Mele I7 is a Allwinner based Android TV box. It features a A31 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out, SPDIF, IrDA, 3 USB A, 1 USB micro OTG and Wireless LAN. Signed-off-by: Marcus Cooper <codekipper@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sun7i: Add support for the MK808C boardMarcus Cooper
The MK808C is a Allwinner based Android TV dongle. It features a A20 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out, 1 USB A, 1 USB mini OTG, Bluetooth and Wireless LAN. Signed-off-by: Marcus Cooper <codekipper@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: Add support for the Jesurun Q5 boardGábor Nyers
The Jesurun Q5 has a black plastic casing with the approximate dimensions of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The storage capacity can be extended up to 32GB with a MicroSD card. The external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to power) and an programmable green led. On the board there is also an unpopulated IR receiver and the UART. The devices is equipped with an AXP209 PMU. For more details see: http://linux-sunxi.org/Jesurun_Q5 Signed-off-by: Gábor Nyers <gnyers@opensuse.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit (git 2.34.1) at 2025-01-10 03:21:59 +0000