| Age | Commit message (Collapse) | Author |
|---|
|
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Enabling ubiload command to load kernel image and
device tree from mtd part labeled "UBI". ubiload
command will search the file from directory /boot.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
When QSPI and NAND is enabled, the ubi and ubifs support
will be enabled too.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
UniPhier SoC family adopt ARM Multi-platform in Linux since the first
upstreaming. Because CONFIG_ARM_PATCH_PHYS_VIRT is defined, the
kernel image is completely position-independent. There is no reason
to decide the load address on compile time, but it is up to the boot
loader. Now, zImage is handier than uImage, also it allows to skip
the relocation of the kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Rename rest of defconfig files of UniPhier SoC family to have the
prefix uniphier_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Now this environment is run-time set to the DTB name U-Boot is really
running with. Drop the static define.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When we want to boot Linux with a DTB file downloaded from a TFTP
server or somewhere, we need to know the file name to be downloaded.
Assume the U-Boot configuration is shared among some similar boards.
If they are similar enough, the difference only appears in device
trees. The build procedure would be like this:
- Board A: make foo_common_defconfig && make DEVICE_TREE=foo_board_a
- Board B: make foo_common_defconfig && make DEVICE_TREE=foo_board_b
- Board C: make foo_common_defconfig && make DEVICE_TREE=foo_board_c
In this case, the U-Boot image contains nothing about the DTB file name
it is running with. (CONFIG_DEFAULT_DEVICE_TREE is not helpful for this
purpose because it is painful to change it from "make menuconfig" for
each board.)
This commit allows to lookup the DTB file name based on the compatible
string and set it to "fdt_file" environment. Then "tftpboot $fdt_file"
will download the file we want.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The UMC (Universal Memory Controller) and the DDR PHY block are
highly related to each other. It is better to have both code in the
same directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Both "Model 1" and "Model 2" are supported for ProXstream2 and
PH1-LD6b boards. It is useful to show the model number in the
boot banner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These are new SoCs from Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compile this file for U-Boot proper as well as SPL, so that the
U-Boot proper can call uniphier_get_board_param().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The DDR3 memory chips on ProXstream2 boards support up to 2133 MHz,
while only up to 1866MHz on PH1-LD6b boards.
Split the board data structure and change the DDR frequency of
ProXstream2 boards to 2133 MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Move "gd->fdt_blob" from the caller to the callee so that this
function can be used more easily.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We sometimes have to implement different code depending on the SoC
revision. This commit adds functions to get the model/revision
number.
Note:
Model number: incremented on major changes of the SoC
Revision number: incremented on minor changes of the SoC
The "Model 2" exists for PH1-sLD3, ProXstream2/PH1-LD6b.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Sync device trees with Linux.
Linux commit: 06ff6b2d63210922a1b1d0f4997e29ce75b5e0c0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These nodes are not parsed by U-Boot for now, but syncing device trees
with Linux is helpful for easier diffing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
UniPhier SoCs (except PH1-sLD3) have several nodes in common.
Factor out them into uniphier-common32.dtsi. This improves the code
maintainability.
PH1-sLD3 is so old that it has more or less different register maps
than the others. So, it cannot be included in this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Return different error code depending on the reason so that the
caller can know the cause of the failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The bit 27-24 of the DTCR register is described as RANKEN in the
DDR PHY databook. Follow this abbreviation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The simple bus support must be enabled in SPL, otherwise the boards
will not be able to parse the DT and will fail to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This node must be available before relocation, otherwise the board
will not find mmc and will thus not boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Enabling MTD default partitions if its not defined in board
configuration file. The layout as below
device nor0 <ff705000.spi.0>, # parts = 6
#: name size offset mask_flags
0: u-boot 0x00100000 0x00000000 0
1: env1 0x00040000 0x00100000 0
2: env2 0x00040000 0x00140000 0
3: UBI 0x03e80000 0x00180000 0
4: boot 0x00e80000 0x00180000 0
5: rootfs 0x01000000 0x01000000 0
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Remove the duplication of SDMMC environment configuration
from each boards' configuration header file into
socfpga_common.h
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
This symbol is not used anywhere, so remove it. For spear600, remove
it from the board file, since the symbol is not defined for spear600
either.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.
This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The L2 cache was never enabled in the v7_outer_cache_enable(), fix
this and enable the L2 cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
This commit adds support of USB 1.1 storage media on AXS103 board.
For some yet unknown reason USB 2.0 doesn't work on AXS103 board issuing
messages like this:
------------------------>8-------------------
AXS# usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
------------------------>8-------------------
As a work-around we're falling back to USB 1.1.
Indeed it is much slower but at least USB storage devices are usable on
AXS103.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
|
|
Marsboard A10 haven't any PMIC at all, so add CONFIG_SUNXI_NO_PMIC=y to
Marsboard_A10_defconfig
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
We need to select DM_KEYBOARD now that the usb-kbd code has been converted
to this, otherwise usb keyboards do not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some sunxi-based boards (such as the Olimex A20-SOM-EVB) have a
second MMC socket. This socket is not bootable hardware-wise,
i.e. u-boot itself cannot be loaded from it, but once u-boot has
started, the second socket can be used in the boot process
provided by config_distro_bootcmd.h.
If a second MMC socket is present, place it in the boot order
after the first MMC socket.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).
Enable the mmc3 controller in the board defconfig.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
