| Age | Commit message (Collapse) | Author |
|---|
|
The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The u-boot-spl.srec is needed for some platforms, add target to generate this file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The u-boot-elf.srec is needed for some platforms, add target to generate this file.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Replace the placeholder DTS for R8A7790 H2 Stout with a proper
DTS from Linux next .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This reduces the size of the binary by about 196 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig. In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files. The previous default
only applied in some cases, even on a specific SoC family.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
function"
Commit d695d6627803 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:
U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0
Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
|
|
The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.
In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.
Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.
References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
|
|
TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So 0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.
Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff
So, Fix the TEXT_BASE for proper aligned address 0xff704000
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
enabled (no actual action is necessary as the gates are open
after reset)
References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
|
|
Since commit ba1f96672522 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.
References: commit ba1f96672522 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
|
|
usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Convert CONFIG_BOOTCOUNT_ALEN to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Make generate boot counter selected in the same way as other boot count
drivers
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Integrate Boot counter for Atmel AT91SAM9XE into Kconfig
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_EXT
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_I2C
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_RAM
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_AM33XX
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Ian Ray <ian.ray@ge.com>
|
|
|
|
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The video drivers (VOP, HDMI encoder, LVDS encoder, MIPI encoder) for
Rockchip SOCs are self-contained and are mainly impacted by other
changes in the architecture support (e.g. pinctrl, clocking, etc).
Let's add these to the list of files maintained as part of the
Rockchip port.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
This migrates rk_vop (the shared functions used by multiple VOP
mini-drivers) to be compatible with a live tree.
Unfortunately, there's
(i) a lot of tree traversal needed for a VOP (as each active VOP
vnode references back to the endpoints in the encoders and vice
versa) to configure the connection between VOPs and encoders;
(ii) the DTS binding is not too sane and one needs to walk a node's
parents (the original code just assumed that the device would
live 3 levels above the property linked through a phandle) until
a UCLASS_DISPLAY device can be found.
As part of the migration, the code for finding the enclosing display
device has been changed to not assume a specific depth of nesting
(i.e. we walk until we reach the root or find a matching device) and
to use the newly introduced (in the same series) ofnode_get_parent()
function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
The rk_hdmi (shared functions for multiple HDMI mini-drivers) has been
using devfdt_get_addr() to read the HDMI controller's IO base address.
This will cause a failure with a live tree.
This changes the driver to use dev_read_addr() which is safe both for
flat trees and live trees.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
We need to get ofnode from a phandle, add interface to support
both live dt and fdt.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The Rockchip video drivers need to walk the ofnode-parrents to find
an enclosing device that has a UCLASS_DISPLAY driver bound. This
adds a ofnode_get_parent()-function that returns the parent-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
|
|
|
|
U-Boot pulled in several core makefiles from Linux. The following
are not used in U-Boot:
- CONFIG_DEBUG_SECTION_MISMATCH
- CONFIG_FTRACE_MCOUNT_RECORD
- CONFIG_GCOV_KERNEL
- CONFIG_GCOV_PROFILE_ALL
- CONFIG_KASAN
- CONFIG_MODVERSIONS
We can remove the unused code if we like. (although it will get the
scripts out of sync)
CONFIG_BOOM and CONFIG_HIS_DRIVER are just mentioned in the comment
block of scripts/basic/fixdep.c
CONFIG_SHELL is not configuration, but a variable for internal-use.
It is just a historical misnomer in Kbuild.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For the omap3_logic boards, the environment is always in NAND.
This removes the ENV_IS_IN_FAT flag to eliminate the extra chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Add entry for ISSI IS25LP256 part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
|
|
Most of architectures have .text section situated in the very beginning
of U-Boot binary and thus it is very logical that CONFIG_SYS_TEXT_BASE
is used on final linkage step to specify where U-Boot gets linked to.
For that we pass the following construction to the LD:
---------------------------->8-----------------------
xxx-ld ... -Ttext $(CONFIG_SYS_TEXT_BASE) ...
---------------------------->8-----------------------
But there could be exceptions. For example:
1. In case of ARCv2 we want to put vectors table in its own section
.ivt in front of .text section which means we need either add an
offset to CONFIG_SYS_TEXT_BASE to compensate for .ivt or don't
pass "-Ttext" to the LD at all and specify link base in linker
script directly.
2. Some architectures even though have .text section in the very
beginning of the U-Boot image still use different symbols to
specify link-base:
* NIOS2: CONFIG_SYS_MONITOR_BASE (which I really like because
that exactly what makes sense - where out image starts but not
beginning of its .text section which just happened to match the
whole image beginning)
* EXTENSA: CONFIG_SYS_TEXT_ADDR
* X86: Which doesn't use CONFIG_SYS_MONITOR_BASE in case of EFI
otherwise sets explicit link base in u-boot.lds
I think that's good to allow for flexibility and don't require each and
every architecture or even platform to specify CONFIG_SYS_TEXT_BASE as well
as use it to set .text section location.
So let's only pass "-Ttext xxx" for those architectures who don't set
link-base explicitly in their linker scripts.
This patch iaddresses comments for previously sent
https://patchwork.ozlabs.org/patch/867540/.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
These were dropped in [1], after relocation, for their values offset by
reloc_off.
Unconditionally show the HW values and add a '(reloc)' hint for the
offset values showed after relocation.
Also, the LRs' dumps are now formatted the same way the other regs' are.
[1] Commit 082693f4 ("arm64 :show_regs: show the address before relocation")
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
|
|
Fix build after addition of RSA_get0_key() to LibreSSL.
Patch from Theo Buehler and Stuart Henderson.
Signed-off-by: Theo Buehler <tb@openbsd.org>
Signed-off-by: Stuart Henderson <sthen@openbsd.org>
|
|
ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.
ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add CONFIG_SPL_NET_VCI_STRING to enable USB-Ethernet boot mode
support.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
