summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-10-16board/bsc9131rdb: Update IFC timings for NAND flashPrabhakar Kushwaha
Current IFC timings for NAND flash are not able to support existing K9F1G08U0B and new K9F1G08U0D flash. so Update the timings to support both. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16powerpc: p1_p2_rdb_pc: add TPL for p1_p2_rdb_pc nand bootYing Zhang
Enable TPL for p1_p2_rdb_pc nand boot. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16powerpc : p1_p2_rdb_pc : Enable p1_p2_rdb_pc to start from eSPI with SPLYing Zhang
Enable p1_p2_rdb_pc to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16powerpc: p1_p2_rdb_pc: Enable p1_p2_rdb_pc to boot from SD Card with SPLYing Zhang
Enable p1_p2_rdb_pc to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16SGMII:fix PHY addresses for QSGMII Riser Card working in SGMII modeZhao Qiang
Fix PHY addresses for QSGMII Riser Card working in SGMII mode on board P3041/P5020/P4080/P5040/B4860. QSGMII Riser Card can work in SGMII mode, but having the different PHY addresses. So the following steps should be done: 1. Confirm whether QSGMII Riser Card is used. 2. If yes, set the proper PHY address. Generally, the function is_qsgmii_riser_card() is for step 1, and set_sgmii_phy() for step 2. However, there are still some special situations, take P5040 and B4860 as examples, the PHY addresses need to be changed when serdes protocol is changed, so it is necessary to confirm the protocol before setting PHY addresses. Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-10-16Corenet/p5040/SGMII:fix the problem for SGMII5/6Zhao Qiang
SGMII5/6 and SGMII7/8 are not on the same slot on P5040 according to the serdes protocol. So it is not proper to organize SGMII5/6 and SGMII7/8 on one bus and SGMII5/6 can't work. So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for SGMII5/6 Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-10-16powerpc/mpc85xx:Avoid fix clk groups for Cluster & HW acceleratorPrabhakar Kushwaha
CHASSIS2 architecture never fix clock groups for Cluster and hardware accelerator like PME, FMA. These are SoC defined. SoC defines :- - NUM of PLLs present in the system - Clusters and their Clock group - hardware accelerator and their clock group if no clock group, then platform clock divider for FMAN, PME Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16powerpc/mpc85xx:Update processor defines for T1040Prabhakar Kushwaha
T1040 SoC has - DDR controller ver 5.0 - 2 PLLs - 8 IFC Chip select - FMAN Muram 192K - No Srio - Sec controller ver 5.0 - Max CPU update for its personalities So, update the defines accordingly. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16powerpc/mpc85xx:Make L2 cache type independent of CHASSIS2Prabhakar Kushwaha
CHASSIS2 architecture never defines type of L2 cache present in SoC. it is dependent upon the core present in the SoC. for example, - e6500 core has L2 cluster (Kibo) - e5500 core has Backside L2 Cache Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16powerpc/c29xpcie: modify DDR parameter to make DDR more stablePo Liu
DDR parameters clk_adjust were changed. This can make the DDR run more stable. The new value were gotten by the DDR testing tool. Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-10-16powerpc:c29xpcie: make ifc timing parameter flexiblePo Liu
This patch re-config the NOR flash timing parameters which could make the ifc timing more flexible for NOR flash. The new parameters could fix the problem of hanging at "Flash:" occasionally when booting the board. Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-10-16powerpc: add CONFIG_SECURE_BOOT condition into fsl_secure_boot.hPo Liu
This patch is for board config file not to add CONFIG_SECURE_BOOT condition for include the asm/fsl_secure_boot.h. Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-10-16Prepare v2013.10Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-16microblaze: Fix watchdog initializationMichal Simek
The patch: "blackfin: Move blackfin watchdog driver out of the blackfin arch folder." (sha1: e9a389a18477c1c57a0b30e9ea8f4d38c6e26e63) changed hw_watchdog_init() prototype which didn't match with Microblaze one. This patch fixes the driver and Microblaze initialization. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-10-16common: fsl: Fix broken SPDX-License-Identifier changeMichal Simek
This bug was introduced by: "Add GPL-2.0+ SPDX-License-Identifier to source files" (sha1: 1a4596601fd395f3afb8f82f3f840c5e00bdd57a) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-10-15mtd: fix warnings due to 64-bit partition supportScott Wood
commit 39ac34473f3c96e77cbe03a49141771ed1639486 ("cmd_mtdparts: use 64 bits for flash size, partition size & offset") introduced warnings in a couple places due to printf formats or pointer casting. This patch fixes the warnings pointed out here: http://lists.denx.de/pipermail/u-boot/2013-October/164981.html Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Tom Rini <trini@ti.com>
2013-10-16spi: mxc_spi: Fix double incrementing read pointer for unaligned buffersTimo Herbrecher
If dout buffer is not 32 bit-aligned or data to transmit is not multiple of 32 bit the read data pointer is already incremented on single byte reads. Signed-off-by: Timo Herbrecher <t.herbrecher@gateware.de> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-10-16sf: probe: Add missing Atmel at25df321 flashBo Shen
As the spi flash transfer to multiple parts, it is forgot to add Atmel AT25DF321 spi flash support, which broken several Atmel EK boards which this chip. So, add it Signed-off-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-16spi: Add GPL-2.0+ SPDX-License-Identifier for missing filesJagannadha Sutradharudu Teki
Added GPL-2.0+ SPDX-License-Identifier for missed spi source files. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-10-16sf: Add GPL-2.0+ SPDX-License-Identifier for missing onesJagannadha Sutradharudu Teki
Added GPL-2.0+ SPDX-License-Identifier for missed sf source files. Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-10-16sf: Minor cleanups.Jagannadha Sutradharudu Teki
- Add comments. - Renamed few macros. - Add tabs. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-10-16sf_ops: Unify bank_sel calculation codeJagannadha Sutradharudu Teki
Unified the bank_sel calculation code for erase and write ops. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-10-15buildman: Use env to pick the python from $PATHJagannadha Sutradharudu Teki
python used in buildman doesn't need to be placed in /usr/bin/python, So use env to ensure that the interpreter will pick the python from environment. Usefull with several versions of python's installed on system. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
2013-10-14Merge branch 'buildman' of git://git.denx.de/u-boot-x86Tom Rini
2013-10-14cmd_sandbox.c: Update for do_(load|save) not taking a number baseTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14Prevent null pointer dereference originating in cmd_pxe.cSteven Falco
Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to avoid possible crashes due to null pointer dereferencing. Commit d7884e047d08447dfd1374e9fa2fdf7ab36e56f5 does not go far enough. There is still at least one call chain that can result in a crash. The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid cmdtp. Passing in NULL is particularly bad in the do_tftpb() case, because eventually boot_get_kernel() will be called with a NULL cmdtp: do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm() -> do_bootm_states() -> bootm_find_os() -> boot_get_kernel() Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the null pointer, and the board will crash. Signed-off-by: Steven A. Falco <stevenfalco@gmail.com>
2013-10-14Coding Style cleanup: drop some excessive empty linesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14Coding Style cleanup: remove trailing empty linesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14Coding Style cleanup: remove trailing white spaceWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14ARM: omap4-panda: Add MAC address creation for pandaDan Murphy
Add a MAC address create based on the OMAP die ID registers. Then poplulate the ethaddr enviroment variable so that the device tree alias can be updated prior to boot. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14pmic: max77686: fix the wrong offsetJaehoon Chung
0x1D is reserved. So BUCK3DVS1 is started from 0x1e. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2013-10-14env_mmc: fix buffer allocation for armv7Markus Niebel
commit d196bd880347373237d73e0d115b4d51c68cf2ad adds redundand environment to mmc. The usage of malloc in env_relocate_spec triggers cache errors on armv7. Tested on a not mainlined i.MX53 board: Board: TQMa53 I2C: ready DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57c2d8 ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f57e2d8 ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57e2e0 ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f5802e0 Using default environment Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
2013-10-14env: dataflash: fix env_init issueBo Shen
As the SPI controller is not initialized before env_init(), it causes reading env in dataflash failed. So, although saveenv() successfully, it shows warning information when reboot the system as following: *** Warning - bad CRC, using default environment Let the env_relocate() to check env CRC and import it. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-10-14ARM: omap4: Update sdram setting for panda rev A6Dan Murphy
OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory part. The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron so the timings needs to be updated Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14am335x_evm.h: Make 'am335x_boneblack' use redundant environmentTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14.gitignore: add auto-generated /include/[s|t]pl-autoconf.mkDaniel Schwierzeck
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-10-14SPDX: document dual license notationWolfgang Denk
In [1] we discussed how we should deal with dual (or, more generally, multiple) licensed files. Add this to Licenses/README so it's properly documented. [1] http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/166518 Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Add the word 'list' to the end of the line, per Stephen Warren's feedback] Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-10-14Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini
2013-10-11Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-10-10buildman: don't fail --list-toolchains when toolchains failStephen Warren
When a toolchain invocation fails, an exception is thrown but not caught which then aborts the entire toolchain detection process. To solve this, request that exceptions not be thrown, since the toolchain init code already error-checks the command result. This solves e.g.: - found '/usr/bin/winegcc' Traceback (most recent call last): ... Exception: Error running '/usr/bin/winegcc --version' Change-Id: I579c72ab3b021e38b14132893c3375ea257c74f0 Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> (formatted to 80cols)
2013-10-10usb: Prevent using reserved registers on DM36x usbAndrew Murray
The musb driver defines and uses MUSB_CSR0_H_DIS_PING, however this bit is reserved on the DM36x. Thus this patch ensures that the reserved bit is not accesssed. It has been observed that some USB devices will fail to enumerate with errors such as 'error in inquiry' without this patch. See http://www.ti.com/litv/pdf/sprufh9a for details. Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk> Acked-by: Marek Vasut <marex@denx.de>
2013-10-09omap5_common: Re-work mmc boot to try SD and eMMC, correct root deviceTom Rini
OMAP5 boards may have both eMMC (on MMC2) and an SD slot (on MMC1). We Update the default bootcmd to match what happens on AM335x where we try SD first, and then eMMC. In this case however, the hardware layout used for powering both of these means that in the kernel eMMC shall be found first as it is powered by a fixed regulator and SD found second as SD is powered via the palmas which will result in deferred probing. Tested-by: Aparna Balasubramanian <aparnab@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-10-09cmd_ubi: add write.part command, to write a volume in multiple partsPaul Burton
This allows you to write data to an UBI volume when the amount of memory available to write that data from is less than the total size of the data. For example, you may split a root filesystem UBIFS image into parts, provide the total size of the image to the first write.part command and then use multiple write.part commands to write the subsequent parts of the volume. This results in a sequence of commands akin to: ext4load mmc 0:1 0x80000000 rootfs.ubifs.0 ubi write.part 0x80000000 root 0x08000000 0x18000000 ext4load mmc 0:1 0x80000000 rootfs.ubifs.1 ubi write.part 0x80000000 root 0x08000000 ext4load mmc 0:1 0x80000000 rootfs.ubifs.2 ubi write.part 0x80000000 root 0x08000000 This would write 384MiB of data to the UBI volume 'root' whilst only requiring 128MiB of said data to be held in memory at a time. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Stefan Roese <sr@denx.de>
2013-10-09cmd_ubi: use int64_t volume size for 'ubi create'Paul Burton
int64_t matches the bytes field in struct ubi_mkvol_req to which the size is assigned. With the prior signed 32 bit integer, volumes were restricted to being less than 2GiB in size. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Stefan Roese <sr@denx.de>
2013-10-09cmd_mtdparts: use 64 bits for flash size, partition size & offsetPaul Burton
This matches the 64 bit size in struct mtd_info and allows the mtdparts command to function correctly with a flash >= 4GiB. Format specifiers for size & offset are given the ll length, matching its use in drivers/mtd in absence of something like inttypes.h/PRIx64. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Stefan Roese <sr@denx.de>
2013-10-09mtd: driver _read() returns max_bitflips; mtd_read() returns -EUCLEANPaul Burton
Linux modified the MTD driver interface in commit edbc4540 (with the same name as this commit). The effect is that calls to mtd_read will not return -EUCLEAN if the number of ECC-corrected bit errors is below a certain threshold, which defaults to the strength of the ECC. This allows -EUCLEAN to stop indicating "some bits were corrected" and begin indicating "a large number of bits were corrected, the data held in this region of flash may be lost soon". UBI makes use of this and when -EUCLEAN is returned from mtd_read it will move data to another block of flash. Without adopting this interface change UBI on U-boot attempts to move data between blocks every time a single bit is corrected using the ECC, which is a very common occurance on some devices. For some devices where bit errors are common enough, UBI can get stuck constantly moving data around because each block it attempts to use has a single bit error. This condition is hit when wear_leveling_worker attempts to move data from one PEB to another in response to an -EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is called to perform the data copy, and after the data is written it is read back to check its validity. If that read returns UBI_IO_BITFLIPS (in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to wear_leveling worker, which then proceeds to schedule the destination PEB for erasure. This leads to erase_worker running on the PEB, and following a successful erase wear_leveling_worker is called which begins this whole cycle all over again. The end result is that (without UBI debug output enabled) the boot appears to simply hang whilst in reality U-boot busily works away at destroying a block of the NAND flash. Debug output from this situation: UBI DBG: ensure_wear_leveling: schedule scrubbing UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083 UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027 UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096 UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083 UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192 UBI: fixable bit-flip detected at PEB 1027 UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083 UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096 UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083 UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096 UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192 UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192 UBI: fixable bit-flip detected at PEB 4083 UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0 UBI DBG: erase_worker: erase PEB 4083 EC 55 UBI DBG: sync_erase: erase PEB 4083, old EC 55 UBI DBG: do_sync_erase: erase PEB 4083 UBI DBG: sync_erase: erased PEB 4083, new EC 56 UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083 UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0 UBI DBG: ensure_wear_leveling: schedule scrubbing UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083 ... This patch adopts the interface change as in Linux commit edbc4540 in order to avoid such situations. Given that none of the drivers under drivers/mtd return -EUCLEAN, this should only affect those using software ECC. I have tested that it works on a board which is currently out of tree, but which I hope to be able to begin upstreaming soon. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Stefan Roese <sr@denx.de>
2013-10-09km/scripts: fix ramfsAndreas Huber
'actual_bank' is not used anymore, instead boot_bank is used. Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
2013-10-09powerpc/km: drop unused CONFIG_SYS_DTT_LOW_TEMPHolger Brunck
This define is not used in u-boot code, we can drop this define safely. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
generated by cgit (git 2.34.1) at 2024-12-29 10:22:57 +0000