| Age | Commit message (Collapse) | Author |
|---|
|
Add some simple tests to verify that the RTC uclass works correctly in
U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Sort these aliases to avoid confusion as to what is present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Enable real-time-clock support in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add an emulated RTC device for sandbox, so that the 'date' command can be
used.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When setting the date, support driver model RTC also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Adjust this command so that it supports using driver model for I2C, i.e.
CONFIG_DM_I2C. This will permit it to be used in sandbox also.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a driver which communicates with the sandbox I2C emulation RTC device
and permits it to be used in U-Boot. This driver is very simple - it just
reads and writes selected I2C registers in the device.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a sandbox I2C emulation device which emulates a real-time clock. The
clock works off an offset from the current system time, and supports setting
and getting the clock, as well as access to byte-width regisers in the RTC.
It does not support changing the system time.
This device can be used for testing the 'date' command on sandbox, as well
as the RTC uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a uclass for real-time clocks which support getting the current time,
setting it and resetting the chip to a known-working state. Some RTCs have
additional registers which can be used to store settings, so also provide
an interface to these.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a function to read the system time into U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move the definition of struct rtc_time into a separate file so that sandbox
can include it without requiring common.h and the like.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need to use u8, and if we avoid it, it isn't so much of a problem
that rtc.h includes this header. With this change we can include rtc.h from
sandbox files.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Most callers unpack the structure and pass each member. It seems better to
pass the whole structure instead, as with the C library. Also add an rtc_
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Rename this function so that it is clear that it is provided by the RTC.
Also return an error when it cannot function as expected. This is unlikely
to occur since it works for dates since 1752 and many RTCs do not support
such old dates. Still it is better to be accurate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Change this function name to something more descriptive. Also return a
failure code if it cannot calculate a correct value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Adjust the printf() string to avoid a warning on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present this driver has a few test features. They are needed for running
the driver model unit tests but are confusing and unnecessary if using
sandbox at the command line. Add a flag to enable the test mode, and don't
enable it by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add driver model versions of the legacy functions to read and write a
single byte register. These are a useful shortcut in many cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Print a debug() message with the I2C speed is exceeded.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
This comment should refer to SPI, not serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
With several chips using the SPI protocol it seems better to put the single
duplex functionality in the EC rather than the SPI driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When starting up, show the protocol version that has been negotiated with
the EC.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Only set the speed if it has changed from last time. Since the speed will
be 0 when the device is probed it will always be changed on the first
transfer after the device is probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Indicate to the emulated sandbox Ethernet driver when we expect a
timeout and tell it to leap forward.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
When called, the next call to receive will trigger a 10-second leap
forward in time to avoid waiting for time to pass when tests are
evaluating timeout behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add a function that maintains an offset to include in the system timer
values returned from the lib/time.c APIs.
This will allow timeouts to be skipped instantly in tests
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Without this, when CONFIG_ENV_VARS_UBOOT_CONFIG is active we get
a compile time error when doing 'make env'.
In file included from tools/env/fw_env.c:117:0:
include/env_default.h:110:11: error: expected ‘}’ before ‘CONFIG_SYS_ARCH’
When building U-Boot this is included indirectly by the compiler switch
-include
/home/trdx/git.toradex.com/u-boot-2014.10-toradex/include/linux/kconfig.h
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
|
|
|
|
By removing this default build target, the "u-boot.kwb" target is not
automatically generated. This fixes a temporary build error when using
out-of-tree builds, as buildman does per default (reported by Simon).
When the full SPL support is added for these targets with the DDR training
code, the "u-boot-spl.kwb" image will be generated automatically.
Users providing a special bin_hdr binary (binary.0) file can always add
this binary file and generate the full firmware image by issuing the
"make u-boot.kwb" command directly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
The macro to select the I2C address for ECC bus-width detection
was defined incorrectly for the Marvell DB-MV784MP-GP board. This
patch changes the macro to the correct value to fix this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:
tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
This solves some RX problems that have been seen, when using the
mvneta ethernet driver. The cache needs to be reset into a "clean"
state before using it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
This enables the usage of the "preboot" environment variable on Marvell
boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
We are not using the coherency feature in U-Boot at all. So lets remove
this configuration from the mbus driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.
Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
This define is used by the DDR training code for Armada XP. With the
upcoming addition of Armada 38x support, lets only define it for
Armada XP in this common header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
MAX_MVNETA_DEVS is not used anywhere in U-Boot. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*
Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.
This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
|
|
|
|
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
|
|
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
|
