| Age | Commit message (Collapse) | Author |
|---|
|
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- Similarly, in mvpp2_buff_hdr_rx(), we introduce a local "cookie"
variable to store the RX descriptor cookie, rather than accessing
it from the descriptor each time.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Some more U-Boot specific 64bit support changes, mostly changing u32
to unsigned long.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Changed by Stefan for U-Boot:
Removed the Kconfig change as it does not apply to U-Boot this way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The macro GENMASK_ULL needs the BITS_PER_LONG_LONG macro which is
defined in the bitsperlong.h header. Lets include this header as
the upcoming A7k/8k support in the Marvell mvpp2 ethernet driver
uses this macro.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We want to use the same device tree blobs in both Linux and U-Boot for
ARC boards.
Earlier device tree sources in U-Boot were very simplified and hadn't been
updated for quite a long period of time.
So this commit is the first step on the road to unified device tree blobs.
First of all we re-organize device tree sources for AXS10X boards.
As AXS101 and AXS103 boards consist of AXS10X motherboard and AXC001 and
AXC003 cpu tiles respectively we add corresponding device tree source
files: axs10x_mb.dtsi for motherboard, axc001.dtsi and axc003.dtsi for
cpu tiles and axs101.dts and axs103.dts to represent actual boards.
Also we delete axs10x.dts as it is no longer used.
One more important change - we add timer device to ARC skeleton device
tree sources as both ARC700 and ARCHS cores contain such timer.
We add core_clk nodes to abilis_tb100, nsim, axc001 and axc003 device tree
sources as it is referenced via phandle from timer node in common
skeleton.dtsi file.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).
In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable mvebu bubt command support on A3720 DB
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable support for Marvell Ethernet PHYs on A37xx platforms
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add default configuration for MACHHIATOBin community board
based on Aramda-8040 SoC.
Change-Id: Ic6b562065c0929ec338492452f765115c15a6188
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add i2c-1 pin mappings to CP0(master) DTSI file
Change-Id: I0c6e6de8a557393f518f7df8e6daa6dfce1788b0
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add GPIO nodes to AP-806 and CP-110-master DTSI files.
Change-Id: I05958698d460cb721b7d8683d34f74a5ea32532c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:
/ {
soc {
mmc0 {
/* ... */
};
};
};
This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
commit 2f11cd9121658 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
|
|
No need to flush cache for command without data.
Signed-off-by: Kevin Liu <kevinliu@asrmicro.com>
|
|
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This patch fixup iommu-map property on pci node to have a valid
mapping of requester-id to stream-id. The requester-id to stream-id
mapping is based on PCI-LUT table initialization.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Layerscape Chasis-2 also uses same PCIe controller as Chasis-3
and have similar PCI-Lut.
Signed-off-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
