summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-11-21x86: Do CPU identification in the early phaseBin Meng
The CPU identification happens in x86_cpu_init_f() and corresponding fields are saved in the global data for later use. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Save the BIST value on resetSimon Glass
The built in self test value is available in register eax on start-up. Save it so that it can be accessed later. Unfortunately we must wait until the global_data is available before we can do this, so there is a little bit of shuffling to keep it around. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Fix up some missing prototypesSimon Glass
Some functions are missing prototypes. Fix those that are specific to x86. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Use the standard arch_cpu_init() functionSimon Glass
Instead of an x86-specific cpu_init_f() function, use the normal U-Boot one for this purpose. Also remove a useless/misleading comment. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Use the standard dram_init() functionSimon Glass
Instead of having an x86-specific DRAM init function, adjust things so we can use the normal one. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Tidy up global descriptor table setupSimon Glass
This code is a little muddled, so tidy it up. Make sure that we put the GDT in the right place and set it up properly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Invalidate TLB as early as possibleSimon Glass
We should invalidate the TLB right at the start to ensure that we don't get false address translations even though paging is disabled. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Remove board_init16() call which is not usedSimon Glass
This allows a board to do very early init, but no boards need to do this. We may as well drop this feature. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-21x86: Remove REALMODE_BASE which is no longer usedSimon Glass
This was missed when the real mode support was dropped. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2014-11-20linux/kernel.h: add typechecking to roundup macroMasahiro Yamada
This commit replaces roundup macro with the one from Linux Kernel. DEFINE_ALIGN_BUFFER must be fixed because typechecking can not be used in this context. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20linux/kernel.h: import more macrosMasahiro Yamada
These macros seem to be useful for U-Boot too (or at least harmless). Imported from Linux 3.18-rc2. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20include: move various macros to include/linux/kernel.hMasahiro Yamada
U-Boot has imported various utility macros from Linux scattering them to various places without consistency. In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN, container_of, DIV_ROUND_UP, etc. In include/linux/compat.h are min_t, max_t, round_up, round_down, etc. We also have duplicated defines of min_t in some *.c files. Moreover, we are suffering from too cluttered include/common.h. This commit moves various macros that originate in include/linux/kernel.h of Linux to their original position. Note: This commit simply moves the macros; the macros roundup, min, max, min2, max3, ARRAY_SIZE are different from those of Linux at this point. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20include/common.h: remove DIV_ROUND definitionMasahiro Yamada
All the references of DIV_ROUND have been replaced with DIV_ROUND_CLOSEST. Remove DIV_ROUND. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20replace DIV_ROUND with DIV_ROUND_CLOSESTMasahiro Yamada
The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible and safer than DIV_ROUND. For example, foo = DIV_ROUND_CLOSEST(x, y++) works expectedly, but foo = DIV_ROUND(x, y++) does not. (y is incremented twice.) Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20ARM: remove CONFIG_ARM1136 definesMasahiro Yamada
CONFIG_CPU_ARM1136 was introduced into Kconfig by commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM1136 and replaces the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM1136. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20ARM: remove CONFIG_ARM926EJS definesMasahiro Yamada
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM926EJS and replaces the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20ARM: remove CONFIG_ARM920T definesMasahiro Yamada
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs). This commit removes all the defines of CONFIG_ARM920T and replaces the only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20ARM: remove CONFIG_ARM1176 definesMasahiro Yamada
CONFIG_ARM1176 is defined for some boards but not referenced at all. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20ARM: remove CONFIG_ARMV7 definesMasahiro Yamada
Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless. Besides, it is never referenced. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-20imx: imx6q/dlsabreauto: Add PMIC Pfuze100 supportYe.Li
Add the pfuze100 initialization in power_init_board for imx6q/dl sabreauto board. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20imx: mx6sxsabresd: Use the pfuze common init functionYe.Li
Modify the pfuze init for mx6sxsabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20imx: mx6sabresd: Use the pfuze common init functionYe.Li
Modify the pfuze init for mx6sabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20imx: mx6sabre common: Factorize the Pfuze init functionYe.Li
Since the Pfuze initializations are similar on various mx6 SABRE boards. Factorize the initialization to a common function in file board/freescale/common/pfuze.c. So that all SABRE boards BSP can share the function. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20power: pfuze100: Update definitions for buck regulatorsYe.Li
Add definitions for buck regulators (SW1A/B/C) registers and voltage values. Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
2014-11-20imx: mx6sxsabresd: Add board support for USDHC2 and USDHC3Ye.Li
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board. The default boot socket is USDHC4, so the MMC environment device and mmcdev variable are set to this device. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20mmc: fsl_esdhc: Update esdhc driver for iMX6SXYe.Li
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0 on iMX6SX. So the fsl_esdhc driver must update to set the register, otherwise no state can be detected. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20mx6sabresd: Access SRC_SBMR1 register via structureFabio Estevam
In U-boot it is preferred to access the register via structure pointer, so convert it such style. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20tqma6: use imx_ddr_sizeMarkus Niebel
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-11-20tqma6: add warning on failed setup_i2cMarkus Niebel
setup_i2c has a return value. Use it to give feedback on error. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-11-20tqma6: add missing includeMarkus Niebel
Add include needed to have prototype for board_spi_cs_gpio Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-11-20tqma6: (cosmetic) remove CONFIG_FLASH_SECTOR_SIZEMarkus Niebel
This is nowhere documented and only used by two other boards. Replace it with TQMA6_SPI_FLASH_SECTOR_SIZE. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-11-20mx6sabresd: Add mx6sabresd_spl_defconfig to MAINTAINERS entryFabio Estevam
Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid getting a warning that the mx6sabresd_spl is not maintained. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6sxsabresd: Simplify the return value of setup_fec()Fabio Estevam
We can simply the return the value from enable_fec_anatop_clock() to make the code smaller and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6slevk: Simplify the return value of setup_fec()Fabio Estevam
We can simply the return the value from enable_fec_anatop_clock() to make the code smaller and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6sabresd: State that only mx6q is supported in SPLFabio Estevam
Make clear that current SPL code only supports the mx6q variant. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx53loco: Fix error handling in board_mmc_init()Fabio Estevam
When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20wandboard: Fix error handling in board_mmc_init()Fabio Estevam
When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20tools/msximage.c: fix warning about nptr possibly uninitializedAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-11-20mx6qsabreauto: Add parallel NOR flash supportFabio Estevam
mx6sabreauto boards come with 32 MiB of parallel NOR flash. Add support for it: U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB Flash: 32 MiB NAND: 0 MiB Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is not used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6: add weim registersFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20imx: consolidate set_chipselect_size functionFabio Estevam
Move MX5 specific set_chipselect_size function into generic i.MX part, such that MX6 based boards are able to use this function as well. While doing this the iomuxc gpr member needed to be consolidated between MX5 and MX6. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6: Use a common SPL configuration fileFabio Estevam
Many boards use a minimal .cfg file in the SPL case. Introduce spl_sd.cfg so that we can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-11-20novena: Move the DCD settings to spl codeFabio Estevam
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR. Move the configuration to the spl code. CCM_CCOSR setting is no longer required to get audio functionality in the kernel, so remove such setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-11-20gw_ventana: Move the DCD settings to spl codeFabio Estevam
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR. Move the configuration to the spl code. CCM_CCOSR setting is no longer required to get audio functionality in the kernel, so remove such setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20mx6sabresd: Move the DCD settings to spl codeFabio Estevam
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR. Move the configuration to the spl code. CCM_CCOSR setting is no longer required to get audio functionality in the kernel, so remove such setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-20imx: fix exception vectors relocation in imx27Albert ARIBAUD
Commit 3ff46cc4 fixed exception vectors setting in the general ARM case, by either copying the exception and indirect vector tables to normal (0x00000000) or high (0xFFFF0000) vectors address, or setting VBAR to U-Boot's base if applicable. i.MX27 SoC is ARM926E-JS, thus has only normal and high options, but does not provide RAM at 0xFFFF0000 and has only ROM at 0x00000000; it is therefore not possible to move or change its exception vectors. Besides, i.MX27 ROM code does provide an indirect vectors table but at a non-standard address and with the reset and reserved vectors missing. Turn the current vector relocation code into a weak routine called after relocate_code from crt0, and add strong version for i.MX27. Series-Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Tested-by: Philippe Reynes <tremyfr@gmail.com> Tested-by: Philippe Reynes <tremyfr@yahoo.fr>
2014-11-20cosmetic: arm: fix whitespace in arch/arm/lib/relocate.SAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-11-20imx: mx6slevk: Change default mmcdev to USDHC2 deviceYe.Li
Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to 1. So modify the default mmcdev in environment variables to dev 1. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20imx:mx6sxsabresd fix pfuz probe failedPeng Fan
The PFUZ probe failed with the following msg: " wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=0 wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=1 wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=2 i2c_init_transfer: give up i2c_regs=021a0000 Can't find PMIC:PFUZE100 " board_early_init_f is too early to call i2c related setting, because init_func_i2c is called after board_early_init_f being invoked. Thus move setup_i2c into board_init. Also PFUZ is connected to I2C bus 0, so change "1" -> "0". Using this patch PFUZ can be correctly probed: "PMIC: PFUZE100 ID=0x11" Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-11-20ARM: mxs: tools: Add support for boot progress display flagAlexey Ignatov
mkimage -T mxs now support new flag in config file: DISPLAYPROGRESS - makes boot process print HTLLC characters for each BootROM instruction. Signed-off-by: Alexey Ignatov <lexszero@gmail.com>