summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-09-01da850/omap-l138: Make MMC and NOR support mutually exclusiveRajashekhara, Sudhakar
On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot work together. This patch enables the MMC/SD support only when NOR support is disabled. NOR Flash identification works even without this patch, but erase and write will have issues. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVMRajashekhara, Sudhakar
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When GP0[11] is low, the SD0 interface will not work, but NOR flash will. When GP0[11] is high, SD0 will work but NOR flash will not. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01da850/omap-l138: Add MMC support for DA850/OMAP-L138Lad, Prabhakar
This patch adds support for MMC/SD on DA850/OMAP-L138. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01omap: am33xx: enable gpio supportSteve Sakoman
This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01omap: am335x_evm: remove unused definitionsSteve Sakoman
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN are defined inn evm.c but not used. Also removes unnecessary include of serial.h PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used. Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01OMAP3: mcx: read hot-water-button after resetStefano Babic
Detect hot-water-button to start a differnt image. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
2012-09-01OMAP3: mcx: updated default environmentStefano Babic
Patch drops also not used CFI setup in the configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
2012-09-01OMAP3: mcx: set pinmux for uart4Stefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
2012-09-01mcx: increased buffer for command lineStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
2012-09-01arm: omap3: cm-t35: minor comment and printf changeIgor Grinberg
Fix the comment to reflect the actual function call time. Change the printf message to look nicer in the context it might be printed. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-09-01hawkboard/omapl-138: Add support for generating ais image for hawkboardSughosh Ganu
Parameters used for configuring certain SoC peripherals are parsed from the cfg file and appended as part of the ais image's header. The u-boot-spl.ais generated is flashed separately to the nand, so do not delete the file after generation of u-boot.ais. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-09-01omap24xx_i2c: add 2-byte address supportIlya Yanok
Various devices like EEPROMs require 2-byte address support to be properly accessed. This patch adds this support for OMAP2/3/4 I2C controller driver. I've tested it with EEPROM (16 bit address) and TPS65217 chip (8 bit address) on TI Beaglebone board. Unfortunately I don't have access to any compatible hardware with 16bit data register so I can't test if those #ifdef clauses really work. CC: Tom Rini <trini@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01CREDITS: Add credits for MCF5249 initialization codeJeremy Andrus
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-01Consolidate bootcount code into drivers/bootcountStefan Roese
This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Manfred Rudigier <manfred.rudigier@omicron.at> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de> Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-09-01mpc52xx: remove o2dnt boardAnatolij Gustschin
Remove old o2dnt board without OF support. New support for this board is added by the previous patch, O2I configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-09-01mpc52xx: add common o2dnt and o2dnt2 support and configurationsAnatolij Gustschin
Add common code for o2dnt and o2dnt2 based boards and add different board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and O3DNT boards. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-09-01mpc5xxx: add GPIO port configurationAnatolij Gustschin
Add posibility for board specifig GPIO configurations using various CONFIG_SYS_ macros. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-09-01mpc5xxx: add pci_mpc5xxx_init prototype to common headerAnatolij Gustschin
Add pci_mpc5xxx_init() prototype to the header file, so board .c files do not need to add extern pci_mpc5xxx_init() declaration. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-09-01Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
* 'master' of git://git.denx.de/u-boot-sh: sh: tmu: Removed arch/sh/include/asm/clk.h sh: tmu: Changed switch statement to shift operation sh: tmu: Changed TMU driver using array of structures Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-01Merge branch 'sf' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'sf' of git://git.denx.de/u-boot-blackfin: sf: spansion: Add support for S25FL256S sf: winbond: fix page_size sf: stmicro: add support for N25Q128A sf: stmicro: add support N25Q128 parts sf: stmicro: support JEDEC standard two-byte signature sf: winbond: add W25Q32 cmd_spi: remove superfluous semicolon Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-08-21sh: tmu: Removed arch/sh/include/asm/clk.hNobuhiro Iwamatsu
asm/clk.h was included get_peripheral_clk_rate function. But this is not used from anywhere. This removed asm/clk.h, and deleted include line from arch/sh/lib/time.c Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-21sh: tmu: Changed switch statement to shift operationNobuhiro Iwamatsu
Calculation of the bit position using switch statement can substitute shift operation using ffs. And removed unsed macro and variable. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-21sh: tmu: Changed TMU driver using array of structuresNobuhiro Iwamatsu
This changed into access using array of structure from access to the register using the definition of the register by macro. And removed white space. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-17Makefile: fix HAVE_VENDOR_COMMON_LIBScott Wood
Commit 8b5a02640adf77301f943e8754992c50df004e8a ("Makefile: cosmetic: optimize usage of LIBS-y") broke the build of boards that have a board vendor "common" directory, by introducing a space between "LIBS-" and "y". Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
2012-08-14sf: spansion: Add support for S25FL256SMichal Simek
Add support for Spansion S25FL256S SPI flash. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-14sf: winbond: fix page_sizeStephen Warren
Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size from 256 to 4096. This prevents either/both of "sf write" writing the correct data, or "sf read" from reading the correct data back. This allows U-Boot running on Compulab Tegra to upgrade itself. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-13mtd/cfi_flash: fix write problems for Numonyx P33/30 32 MBit flashsHolger Brunck
commit 54652991 Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads to problems for smaller versions of this chip e.g. the 32Mbit version with deviceid 0x16 on mgcoge. So move the code for this work around to an own function and check previously manufacturer id and device id to not break other flashes which don't need this work around. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Stefan Roese <sr@denx.de> cc: Philippe De Muyter <phdm@macqel.be> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Stefan Roese <sr@denx.de>
2012-08-13cfi_flash: add support for Spansion flash PPB sector protectionAnatolij Gustschin
Erasing flash sectors protected with persistent protection bit (PPB) mechanism on Spansion flash chips doesn't work. Add sector protection status checking and sector lock and unlock commands to fix this. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-08-10dts/Makefile: Turn off some predefined macrosHorst Kronstorfer
Add '-ansi' to DTS_CPPFLAGS to avoid unwanted expansion of dts content that matches some predefined macros. Example: A number of PowerPC related *.dts files in the kernel define a property named 'linux,network-index' which (w/o '-ansi') is expanded to '1,network-index' by the preprocessor because of '#define linux 1.' Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
2012-08-10Add support for DS1388.Kenth Eriksson
Support for DS1388 is added by extending the DS1337 driver. DS1388 is similar to DS1337. The time registers are offset by 1 (due to support for hundreds of seconds), and there is no century bit. The configuration and trickle charge registers are also different. Tested on hardware with Freescale P2010 and DS1388. Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
2012-08-10dts/Makefile: Check for empty $(LDSCRIPT)Horst Kronstorfer
Make sure that $(LDSCRIPT) is not empty before calling process_lds with 'cat $(LDSCRIPT)' else cat will block waiting for input from stdin. Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
2012-08-10Makefile: cosmetic: optimize usage of LIBS-yDaniel Schwierzeck
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-08-10Makefile: replace LIBS by LIBS-yDaniel Schwierzeck
Synchronize with ALL-y handling and code in spl/Makefile. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-08-10Makefile: allow appending to LIB in sub-makefilesDaniel Schwierzeck
The top Makefile and the SPL Makefile have lines like those: ifneq ($(CONFIG_AM33XX)$(CONFIG_OMAP34XX)$(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),) LIBS += $(CPUDIR)/omap-common/libomap-common.o endif ifeq ($(SOC),mx5) LIBS += $(CPUDIR)/imx-common/libimx-common.o endif This should be done in the arch/CPU/SoC specific sub-makefiles to keep the top Makefiles clean. This patch also allows adding of new arch/CPU/SoC specific libraries in the future without touching the top Makefiles. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-08-11nds32: fix unused pmu_init warningMike Frysinger
Fixes the build-time warning: board.c: At top level: board.c:106: warning: 'pmu_init' defined but not used This makes the ifdef logic at the call site match the logic at the function definition. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-11nds32: delete unused local variableMike Frysinger
Fixes the build-time warning: board.c: In function 'board_init_r': board.c:304: warning: unused variable 's' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-11nds32: drop bi_enetaddr from global dataMike Frysinger
Nothing is using this, so punt it from the gd. Seems to just be a copy & paste wart from the initial port. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-10sf: stmicro: add support for N25Q128AMichal Simek
Add support for Numonyx N25Q128A SPI flash. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09sf: stmicro: add support N25Q128 partsStephan Linz
Adds support for Numonyx's N25Q128 SPI flash. These devices are used on (among others) Avnet Spartan-6 LX9 micro-evaluation boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH. Signed-off-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09sf: stmicro: support JEDEC standard two-byte signatureStephan Linz
There are more than the M25Pxx serial flashs that can be used with the stmicro driver, for example: the M25PXxx or N25Qxx serie. All these chips have burned in the original stmicro manufacture id 0x20 together with a standard two-byte signature. In preperation to support all these chips the stmicro driver have to decode the full two-byte signature. Signed-off-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09sf: winbond: add W25Q32Rajeshwari Shinde
SMDK EVT1 has a different Winbond part, added its part details to the SPI flash table. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09cmd_spi: remove superfluous semicolonMarek Vasut
Reported-by: James Miller <jamesmiller@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09zfs: Add ZFS filesystem supportJorgen Lundman
U-Boot port is based on sources forked from GRUB-0.97 by Sun in 2004, which can be found here: http://src.opensolaris.org/source/xref/onnv/onnv-gate/usr/src/grub/grub-0.97/stage2/zfs-include/zfs.h Released by Sun for GRUB under the license: * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. GRUB official releases include ZFS in version: ftp://alpha.gnu.org/gnu/grub/grub-1.99~rc1.tar.gz And patched against GRUB Bazaar repository for ashift fixes (4KB HDDs) more conveniently found at github: https://github.com/pendor/grub-zfs/commit/e7b6ef3ac3b9685ac4c394c897b1d4221b7381f1 Signed-off-by: Jorgen Lundman <lundman@lundman.net>
2012-08-09u-boot: Update yaffs2 file systemCharles Manning
This patch updates the yaffs2 in u-boot to correspond to git://www.aleph1.co.uk/yaffs2 commit id 9ee5d0643e559568dbe62215f76e0a7bd5a63d93 Signed-off-by: Charles Manning <cdhmanning@gmail.com>
2012-08-09openrisc: Work around potential relocation issuesJulius Baxter
When reset code is in flash, the jump instructions emitted by the compiler are relative instead of absolute jumps. A fix to the reset code to make correct jumps to the beginning of code relocated to RAM have also been added. Signed-off-by: Julius Baxter <juliusbaxter@gmail.com>
2012-08-09rename EB+MCF-EV123 to its current marketing name EB+CPU5282Jens Scharsig
* rename board directory to eb_cpu5282 * rename EB+MCF-EV123_.*config to eb_cpu5282_.*config * add Maintainer for EB+CPU5282 board * rename prompt Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-08-09Consider CONFIG_ZERO_BOOTDELAY_CHECK when CONFIG_AUTOBOOT_KEYED is setDirk Eibach
When CONFIG_ZERO_BOOTDELAY_CHECK is not defined, bootdelay==0 prevents the check for console input (as stated in README.autoboot). This must also work in CONFIG_AUTOBOOT_KEYED mode. Signed-off-by: Dirk Eibach <eibach@gdsys.de>
2012-08-09mkconfig: add support for SPL CPUAllen Martin
Add support for specifying a differnt CPU for main u-boot and SPL u-boot builds. This is done by adding an optional SPL CPU after the main CPU in boards.cfg as follows: normal_cpu:spl_cpu This this case CPU will be set to "normal_cpu" during the main u-boot build and "spl_cpu" during the SPL build. Signed-off-by: Allen Martin <amartin@nvidia.com>
2012-08-09configs: Remove unused symbol CONFIG_DISCOVER_PHYFabio Estevam
CONFIG_DISCOVER_PHY is not used anywhere, so remove it from config files. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-08-09Build: Ignore build tree and IDE control fileTimo Ketola
Signed-off-by: Timo Ketola <timo@exertus.fi>
generated by cgit (git 2.34.1) at 2024-12-26 06:30:40 +0000