| Age | Commit message (Collapse) | Author |
|---|
|
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.
Tested with DHCOM i.MX6dl and DHCOM i.MX6q.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
For a single binary approach for imx6 quad/dual/duallite/solo it
is necessary to enable CONFIG_SATA for quad/dual. On the other hand
on imx6 duallite/sole SATA is not available.
Therefore sata_remove() is skipped according to a blacklist scheme.
Adding further imx derivates is probably not recessary as they are
usually not pin-compatible and therefore a different board with its
own configuration.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
|
|
It turned out that after a reset the boot process from the spi bootflash is
disturbed by other spi slave devices connected to DHCOM SPI1, which uses the
same spi interface with a different SS line.
Therefore the pad pull ups are enabled.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
|
|
Fix issue as reported by checkpatch.pl. Leave long lines as line
continuation in text output is not recommended.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The Apalis iMX8 was missing the interactive part should a customer have
bricked his module and want to re-create the configuration block. Fix
this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The Colibri iMX8X target got re-named late in the cycle which we forgot
to reflect here. Furthermore, it was missing the interactive part should
a customer have bricked his module and want to re-create the
configuration block. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Make the interactive Wi-Fi/BT handling generic by pulling it out of the
Colibri iMX6ULL interactive part to be re-used for Apalis iMX8 and
Colibri iMX8X.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
If the module is in serial downloader mode, we do no longer read the
environment from eMMC. Therefor, the eMMC is unitialized when trying
to read the config block. Use mmc_init to initialize the selected
MMC device before using it.
Note: In case the MMC has already been initialized, the mmc_init
detects that and returns immediately.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
According to iMX6DQ RM, the minor field (low 8 bits) in DIGPROG is not
aligned on silicon revision 1.3. So update get_cpu_rev to correct the
revision.
0x00630002 Silicon revision 1.2
0x00630005 Silicon revision 1.3
0x00630006 Silicon revision 1.6
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch fixes not enabled uart2 (and hence serial console) on i.MX53
devices. After following commit 1d255904c306 ("ARM: dts: imx: imx53:
Synchronize iMX53 DT with Linux") from the uart2 compatible the
'fsl,imx7d-uart' has been removed (which was correct).
However, the root cause of the problem was the commit 98d62e618bb9 ("arm:
imx: add i.MX53 Beckhoff CX9020 Embedded PC") which introduced this
compatible.
Moreover, without this patch all i.MX53 UARTs are not usable as neither
'fsl,imx53-uart' nor 'fsl,imx21-uart' are in compatible IDs in
drivers/serial/serial_mxc.c file.
The fix is to add 'fsl,imx53-uart' and 'fsl,imx21-uart' as compatibles
for the aforementioned serial driver (those are also defined in the Linux
kernel).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
This patch disables support for running EFI applications on HSC|DDC boards.
As a result - considerable size reduction (~14%) has been observed (for
for u-boot-dtb.imx 475KiB to 407KiB).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Configure fitImage for U-Boot with a device tree for imx6 quad/dual
and duallite/solo. This enables to support the imx6 derivates
quad/dual/duallite/solo with a single binary.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This device tree adds support for DHCOM iMX6 duallite and solo
deriviates.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
imx6 duallite
To use the device tree definitions imx6q-dhcom-som.dtsi for all imx6 derivatives rename
it to imx6qdl-dhcom.dtsi. We omit the '-som', because it simplifies further mainlinening
of already existing device trees.
To reuse board level common stuff imx6qdl-dhcom-pdk2.dtsi is created and included by
imx6q-dhcom-pdk2.dts.
Signed-off-by Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Enable DM support for regulators and fixed regulator driver and
convert USB Vbus control over to the regulators defined in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Ludwig Zenz <lzenz@dh-electronics.com>
|
|
1. Introduce androidboot wrapper for booting AOSP.
2. Add partitions_android env var for simplifying the process of
writing new gpt table from U-boot shell/fastboot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: output: 1 [x] dbg1.gpios
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
imx6ul-isiot-mmc.dts was removed in uboot version v2018.03 and from then
onwards IMX6UL isiot uses imx6ul-isiot-emmc.dts for mmc, so remove
unnecessary check for mmc.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Secure boot is not enabled in mx6sxsabresd imximage.cfg, add support
for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Move build_info() to common place.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable CONFIG_ARMV7_BOOT_SEC_DEFAULT by default to avoid a kernel
crash when booting NXP linux kernels in non-secure world,
when job ring device allocation is done by CAAM hw accelerator driver:
caam 30900000.caam: job rings = 3, qi = 0
caam_jr 30901000.jr0: failed to flush job ring 0
caam_jr: probe of 30901000.jr0 failed with error -5
caam_jr 30902000.jr1: failed to flush job ring 1
caam_jr: probe of 30902000.jr1 failed with error -5
caam_jr 30903000.jr2: failed to flush job ring 2
caam_jr: probe of 30903000.jr2 failed with error -5
caam algorithms registered in /proc/crypto
Job Ring Device allocation for transform failed
caam 30900000.caam: caam pkc algorithms registered in /proc/crypto
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = c0004000
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted:
Hardware name: Freescale i.MX7 Dual (Device Tree)
task: ec0d8000 task.stack: ec0ce000
PC is at caam_sm_startup+0x3f8/0x4f4
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
Unfortunately, that missing M makes the current downstream NXP BSP
4.14.98_2.0.0_ga crash early during Linux kernel boot. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
This patch enable usb support with device-tree
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
|
|
Enable DM Watchdog support on iMX53 M53Menlo.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The DM_FLAG_PRE_RELOC shall be set unconditionally as this driver is going
to be re-used in both early SPL and U-Boot proper's pre-reloc.
For i.MX based devices it is crucial to have available the serial console
before relocation (otherwise the board may hand).
The device definition may be provided either via device tree description or
with U_BOOT_DEVICE(mxc_serial) definition. In the latter case the device
will not bind in U-Boot proper when DM_FLAG_PRE_RELOC is not set.
The !CONFIG_IS_ENABLED(OF_CONTROL) #if check was set as a "workaround" for
DM problem described in following commit 4687919684e0
("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers").
Let's look on this check more thoroughly - we add this flag if the board
doesn't support OF_CONTROL. This is a bit strange as the serial_mxc.c can
be used with CONFIG_DM_SERIAL but without corresponding device tree
description (OF_CONTROL). In such case the aforementioned
U_BOOT_DEVICE(mxc_serial) definition is used.
Other boards/SoCs have this flag set unconditionally for serial driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Add DM and DT probing support to iMX watchdog driver. This should
allow boards to move over to this driver, enable SYSRESET_WATCHDOG
to handle cpu_reset() if required.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
|
|
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
|
|
Before the wide DM/DTS adoption in the U-Boot proper, the display5
has been using only DM_SERIAL to provide serial console in
pre-relocation.
After moving to full DM/DTS adoption in the U-Boot proper the
U_BOOT_DEVICE definition is not needed anymore, as it has been
replaced with udevice creation from provided DTS description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This file setups UART5 based serial to be used as pre-relocation
console in the U-Boot proper.
On purpose pinux configuration is omitted here as it has been already
done in SPL. For early pre-relocation code we only need the serial
device from DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This commit ports from Linux kernel - tag: v5.1 - the device tree
description for display5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Porting more DTS code from Linux kernel for display5 board required
increase of pre-relocation malloc pool size in U-Boot proper.
The early malloc memory is necessary for handling parsing and setup of
e.g. serial port device (and all its ancestors in DT tree).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Add missing parenthesis to the GPIO_TO_PORT macro.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
After commit 14453fbfadc2 ("Convert CONFIG_SF_DEFAULT_* to Kconfig")
and commit abe66b1b5dec ("Convert CONFIG_ENV_SPI_* to Kconfig") ,which
moved some SPI related CONFIG_* defines to Kconfig the display5 board has
become unbootable as the SPI CS check condition had wrong value.
This commit fixes this check and allows proper SPI NOR flash operation in
SPL.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit just corrects spelling of 'accessed' word in the EEPROM
comment.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Some comments are not needed anymore after Kconfig automated conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This would be used for writing spl images along nand BCB
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.
So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
add DM support for pwm-imx driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add Kconfig support for this driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Martyn Welch <martyn.welch@collabora.co.uk>
|
|
This function sets the polarity of the PWR signal which is not used on
the opos6uldev board. Remove it.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
This commit updates the doc/README.falcon regarding Falcon boot on
NOR flash memories.
This code is used by MCCMON6 board - so for more details please refer to
configs/mccmon6_nor_defconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This option will provide the offset in the parallel NOR flash memory to,
which the falcon boot data is stored.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The CMD_SPL_NAND_OFS description was a bit misleading, has
been updated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit makes the CMD_SPL_NAND_OFS only visible when we use NAND
memory.
Before this change it was present when only CMD_SPL was enabled (and
would stay when board with other falcon boot medium is used).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
mccmon6 works in 10/100 MiB Ethernet environment, so disabling 1GiB support
improves robustness of the network after power up (as one don't need to
wait for autoneg).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The IMX6Q based MCCMON6 is not using USB for any purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
