summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-01-1685xx: convert remaining 85xx boards over to use new LAW init codeKumar Gala
Converted ATUM8548, MPC8568 MDS, MPC8540 EVAL, and TQM85xx boards over to use new LAW init code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert STXGP3/STXSSA over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert PM854/PM856 over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert SBC8540/SBC8560/SBC8548 over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert MPC8541/MPC8555/MPC8548 CDS over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert MPC8540/MPC8560 ADS over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: convert MPC8544 DS over to use new LAW init codeKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-1685xx: Move LAW init code into CKumar Gala
Move the initialization of the LAWs into C code and provide an API to allow modification of LAWs after init. Board code is responsible to provide a law_table and num_law_entries. We should be able to use the same code on 86xx as well. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-16Merge branch 'master' of git://www.denx.de/git/u-boot-mpc86xxWolfgang Denk
2008-01-16Add support for the MPC837xERDBKim Phillips
MPC837xERDB board support includes: * DDR2 330MHz hardcoded (soldered on the board) * Local Bus NOR Flash * I2C, UART and RTC * eTSEC RGMII (TSEC0 - RTL8211B with MII; * TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware * load) Signed-off-by: Kevin Lam <kevin.lam@freescale.com> Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: add support for more system clock performance controlsKim Phillips
System registers that are modified are the Arbiter Configuration Register (ACR), the System Priority Control Register (SPCR), and the System Clock Configuration Register (SCCR). Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com> Signed-off by: Joe D'Abbraccio <ljd015@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16FSL: Generalize PIXIS reset command parsing.James Yang
Before, the order of arguments to the pixis_reset command needed to be supplied in a hard-coded order. Generalize the command parsing to allow any order. Signed-off-by: James Yang <james.yang@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
2008-01-16FSL: Convert board/freescale/common/Makefile to use CONFIG_Jon Loeliger
Convert the board/freescale/common/Makefile to use CONFIG_* options to select which files to conditionally compile into the board/freescale/common library rather than conditionally compiling entire files. Now handles:: CONFIG_FSL_PIXIS CONFIG_FSL_DIU_FB CONFIG_PQ_MDS_PIB CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-01-16Use CONFIG_ULI526X as MPC8610HPCD default Ethernet driverRoy Zang
Use driver/net/uli526x.c as MPC8610HPCD default Ethernet driver. Remove unused ethernet CONFIG_ options. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
2008-01-16mpc83xx: fix QE ETHPRIMEs to correct 'FSL UEC0' valueKim Phillips
continuation of commit b96c83d4ae475a70ef2635cd0e748174c44c8601 Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: clean up mpc8360emds.c warningsKim Phillips
mpc8360emds.c: In function 'ft_board_setup': mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: fix phy-connection-type fixup codeKim Phillips
use tree passed to us in local blob, not global fdt. Also use fdt_path_offset to convert to relative offset, since absolute reference is needed to check for rgmii-id mode string value. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: fix mpc8313/mpc8315/mpc8349itx Makefiles for silent build (with -s)Kumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16Changes in uboot DDR configuration for MPC8313eRDBPoonam Aggrwal
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for DDR configuration in u-boot code. Some are related to performance, some affect stability and some correct few basic errors in the current configuration. The changes have been tested and found to give better memory latency figures on MPC8313eRDB.LMBench figures prove it. The changes are: - CS0_CONFIG[ AP_n_EN] is changed from 1 to 0 (this may improve performance for application with many read or write to open pages). - CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to 001 (activating all the CS when only one is used may cause unwanted noise on the system) - TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on Tras=45ns) - TIMING_CFG_1[REFREC] changed from 21 clks to 18clks. - TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to comply with the 3 ODT clk requirements) - TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4. - TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks. - DDR_SDRAM_MODE[AL]changed from 0 to 1. - DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks. - DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510. - DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500. The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git The last commit on this tree was 6775c68683a53c7abc778774641aac6f833a2cbf Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com> Cc: Bill HighSmith <Bill.Highsmith@freescale.com> Cc: Razzaz Mazyar <MRazzaz@freescale.com> Cc: Josep P J <PJ.Joseph@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16Enable the isdram command on the MPC8360EMDS boardJerry Van Baren
The isdram command prints out decoded information the "serial presence detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when debugging memory configuration problems. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Add the support for MPC8315ERDB boardDave Liu
The features list: - Boot from NOR Flash - DDR2 266MHz hardcoded configuration - Local bus NOR Flash R/W operation - I2C, UART, MII and RTC - eTSEC0/1 support - PCI host Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Add config of eTSEC emergency priority in SPCRDave Liu
The TSEC emergency priority definition of 831x/837x is different than the definition of 834x in SPCR register. Add the other config of TSEC emergency priority into cpu_init.c Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16mpc83xx: Remove cache config from MPC8360ERDK.hDave Liu
The MPC8360ERDK board support patch is added before the commit 2c5b48fc205c3e2752910da8f39209ed075929e5 so, miss clean up it. The patch clean up the miss cache config. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16nand: FSL UPM NAND driverAnton Vorontsov
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16OneNAND: Separate U-Boot dependent code from OneNANDKyungmin Park
OneNAND: Separate U-Boot dependent code from OneNAND Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-01-16LWMON5: enable hush shell as command line parserWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-15ADS5121: disable watchdog; enable image timestampsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-15TK885D: fixes for bigger flash sector sizes on new modules;Wolfgang Denk
adjust default environment; disable SCC ethernet (not used on this board). Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-14Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk
2008-01-14QE: fix compile warningDave Liu
qe.c: In function 'qe_upload_firmware': qe.c:390: warning: pointer targets in passing argument 2 uec.c: In function 'uec_initialize': uec.c:1236: warning: 'uec_info' may be used uninitialized Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-01-14ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bitStefan Roese
Now that bit 29 is the USB PHY reset bit, update the Kilauea port to remove the USB PHY reset after powerup. The CPLD will keep the USB PHY in reset (active low) until the bit is set to 1 in board_early_init_f(). Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-13ARM: update mach-types.h from 2.6.24-rc7 Linux kernel treeWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: Fix typo in ads5121.c, adjust default environmentWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: MAX slew rate for PATA pinsJohn Rigby
Signed-off-by: John Rigby <jrigby@freescale.com>
2008-01-13Fix Makefile dependency problem with parallel builds.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8544DS: fix board Makefile for silent build (with -s)Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13PMC440 board: fix board Makefile for out-of-tree buildingWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Makalu: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/masterWolfgang Denk
2008-01-13cmd_nand : fix compiler warning.Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-01-13CFI: Fix CONFIG_FLASH_CFI_LEGACY compilationMichael Schwingen
Signed-off-by: Michael Schwingen <michael@schwingen.org> Acked-by: Stefan Roese <sr@denx.de>
2008-01-13Merge branch 'master' of /home/stefan/git/u-boot/u-bootStefan Roese
2008-01-13MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBESWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8xx FEC driver: fix compiler warning.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Fix Makefile dependencies issues; allow silent buildWolfgang Denk
- get rid of "version" target whichdidn't really work - make autoconf.mk depend on version_autogenerated.h to make sure to rebuild files as needed - add XECHO macro to allow for silent build using "make -s" Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121e: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MUNICes: fix board Makefile for remote build directoryWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12MPC5200: don't use hardcoded MBAR address in Bestcomm firmwareOliver Weber
Signed-off-by: Oliver Weber <almoeli@gmx.de>
2008-01-12Make bootretry work when command line editing is enabledAndreas Engel
Currently, when CONFIG_CMDLINE_EDITING is set, bootretry doesn't work. This patch fixes the problem. Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-01-12Refactor code for "i2c sdram" commandLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
generated by cgit (git 2.34.1) at 2024-12-27 04:42:06 +0000