| Age | Commit message (Collapse) | Author |
|---|
|
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry.
Tested on real silicon and confirmed to be working.
Signed-off-by: Bacem Daassi <Bacem.Daassi@cypress.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Commit 658df8bd9464 ("mtd: spi-nor-core: Add octal mode support")
enables octal mode(1-1-8) support in spi-nor framework.
mt35xu512aba and mt35xu02g supports SINGLE and OCTAL I/O. Hence, enable
SPI_NOR_OCTAL_READ flag for these flashes.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.
Tested on u-boot-ti/next.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
hweight32 is a somewhat expensive way to check for power-of-2. Use the
is_power_of_2 helper, which does the standard and cheap idiom
foo&(foo-1)==0.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-96 (-96)
Function old new delta
spi_nor_write 388 292 -96
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
To support the SPI MEM API, instead of modifying the existing U-Boot
driver, this patch adds a port of the existing Linux driver.
This also has the advantage that porting changes and fixes from Linux will
be easier.
Porting of driver left most of the functions unchanged while few of the
changes are:
-Remove lock(mutexes) and irq handler as u-boot is a single core execution.
-Remove invalid masterid as it was required specially for multicore
execution in LS2088ARDB which is not the case in u-boot.
-Remove clock support as changing spi speed is not supported in uboot and
nor in linux.
Currently tested on LS1088ARDB, LS1012ARDB, LS1046ARDB, LS1046AFRWY,
LS1043AQDS, LS1021ATWR, LS2088ARDB, I.MX6ULL EVK.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This converts the following to Kconfig:
CONFIG_PHYLIB
CONFIG_BITBANGMII
CONFIG_MV88E6352_SWITCH
CONFIG_MV88E61XX_SWITCH
CONFIG_PHYLIB_10G
CONFIG_PHY_AQUANTIA
CONFIG_PHY_ATHEROS
CONFIG_PHY_BROADCOM
CONFIG_PHY_CORTINA
CONFIG_PHY_DAVICOM
CONFIG_PHY_ET1011C
CONFIG_PHY_LXT
CONFIG_PHY_MARVELL
CONFIG_PHY_MICREL
CONFIG_PHY_NATSEMI
CONFIG_PHY_REALTEK
CONFIG_RTL8211X_PHY_FORCE_MASTER
CONFIG_PHY_SMSC
CONFIG_PHY_TERANETICS
CONFIG_PHY_TI
CONFIG_PHY_VITESSE
CONFIG_PHY_XILINX
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When moving the PHYLIB PHY drivers around in Kconfig we did not at the
same time perform a careful migration of the related drivers and
sub-options. This lead to the case where previously Kconfig-enabled
driver choices were now disabled on some platforms. Correct this by
enabling both the PHY driver and sub-option on the above referenced
platforms.
Fixes: af2cbfd6b982 ("drivers: net: Provide Kconfig menu for PHYLIB")
Fixes: 8728c97eff5b ("configs: Re-sync")
Reported-by: Dario <dario86@tutamail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Currently generic-asm-offsets.h and asm-offsets.h are generated based
on U-Boot proper config options. The same asm-offsets headers are used
for building U-Boot SPL/TPL, which causes potential offset mismatch if
U-Boot proper has different config options from U-Boot SPL/TPL.
This commit adds:
spl/include/generated/(generic-)asm-offsets.h
tpl/include/generated/(generic-)asm-offsets.h
spl/include/generated/(generic-)asm-offsets.h is generated if
CONFIG_SPL=y, and included when building SPL.
tpl/include/generated/(generic-)asm-offsets.h is generated if
CONFIG_TPL=y, and included when building TPL.
They are created before Kbuild descends into SPL/TPL object directories
and builds $(obj)/dts/dt-platdata.o because $(obj)/dts/dt-platdata.c
includes a bunch of headers.
Prepend -I$(obj)/include to $(UBOOTINCLUDE) so (generic-)asm-offsets.h
is searched in {spl,tpl}/include/generated/.
Requested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Synchronize R-Car Gen2 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The r8a779{5,6,65}_salvator-x and r8a779{5,6,65}_ulcb_defconfig were
building the same target, except for the default DT. The default DT is
however only a detail, as the actual DT to be used to configure U-Boot
is detected automatically based on the CPU ID, hence the default DT is
not meaningful. Unify each three defconfigs per board to reduce the
duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
|
|
- DWC2/DWC3 improvements
- Assorted bugfixes
|
|
|
|
Move Python tools to use absolute paths
Minor buildman fixes for new features
Make libfdt code more similar to upsteam
|
|
Update mcinitcmd and bootcmd environment variable for emmc boot.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Enable GIC_V3_ITS config to initialize the GIC redistributor
tables.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Enable GIC_V3_ITS config to initialize the GIC redistributor
tables.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Enable GIC_V3_ITS config to initialize the GIC redistributor
tables.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The GIC redistributor tables initialization depends on RESV_RAM config,
so select RESV_RAM if GIC_V3_ITS is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
As the lower 16bit of the redistributor pending table is reserved
for describing the memory attributes, we must give a 64KB aligned
address to the GIC LPI initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Program the GIC redistributor tables only when succeeded to reserve memory
for them, otherwise kernel will lose the chance to program them using
allocated memory.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The initialization of gd->arch.resv_ram pointer should depend on if the
RESV_RAM config is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ.
Update DDR struct to set new WRLVL_START values so that the new DIMM
MTA18ADF2G72AZ get optimized and the old DIMM still works.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The default reserved memory for CMA is high memory. If LPAE is enabled,
highmem pages are non-remapped and can not be used with
dma_alloc_coherent. Reserving low memory for CMA is needed for LS1021A.
This patch appends the related CMA configuration to bootargs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add support of dhcp boot for ls1012afrwy
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add stub for functions clk_...() when CONFIG_CLK is deactivated.
This patch avoids compilation issues for driver using these API
without protection (#if CONFIG_IS_ENABLED(CLK))
For example, before this patch we have undefined reference to
`clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);
clk_release_bulk(&priv->clks);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
free() checks if its argument is NULL. Do not duplicate this check.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The free() function checks if the argument is NULL.
Do not duplicate this check.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Power on/off the PHYs to enable power to the USB ports, fixing USB support
on Khadas VIM3/VIM3L boards.
The G12A USB complex has at least 2 USB2 PHYs, but one is muxed between the
DWC2 and DWC3 controller and the other one directly connected to the DWC3
controller. The USB3+PCIe combo PHY is muxed between the DWC3 controller
and a DW-PCIE controller.
All PHYs are optional, but it's type (usb2/usb3) and position are important
to determine it's capabilities, thus they are stored in a fixed size
array and the phy-name determines it's position, it's position determining
it's type and functionnalities.
This is why we need to loop over the array to power on all the DT provided
PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Enable the necessary configs to make usage of the SPI NOR Flash.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable the SPI flash controller and reduce the usable eMMC data pins to 4
to permit using the on-board SPI NOR Flash.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add the necessary configs to use the SPI NOR flash.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Activate the on-board SPI NOR Flash by enabling the SPI controller and
disabling the DS eMMC pin in the VIM2 u-boot.dtsi file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Sync the device tree and dt-bindings from Linux v5.7-rc1 8f3d9f354286
("Linux 5.7-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This adds support for the USB PHY found on Amlogic GXBB SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add missing SD_EMMC_A controller gates needed for probe of the A
controller, otherwise leading to a freeze of the SoC after b3d69aa596.
Fixes: b3d69aa596 ("clk: meson: reset mmc clock on probe")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
- Assorted bugfixes.
- Documentation improvements including support for https://u-boot.readthedocs.io/
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-arc
Here we introduce new development platfrom for ARC: HSDK 4xD.
That's pretty much the same base-board as in HSDK but with
very recent quad-core ARC HS47D in the ASIC.
Thus we try to re-use existing code as much as possible while
inevitably add some pieces needed for the new ASIC.
Also we drop selection of bounce buffers on AXS10x
as there's no use of them any longer.
|
|
At this point LLVM-7 is rather old. Switch over to LLVM-10 to enable
some amount of CI coverage with newer compilers.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
At this point LLVM-7 is rather old. Switch over to LLVM-10 to enable
some amount of CI coverage with newer compilers.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This provides a newer ARC toolchain along with being based on a newer
Ubuntu bionic tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
