summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-04-24powerpc/corenet_ds: Master module for boot from SRIOLiu Gang
For the powerpc processors with SRIO interface, boot location can be configured from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash for u-boot image. The image can be fetched from another processor's memory space by SRIO link connected between them. The processor boots from SRIO is slave, the processor boots from normal flash memory space and can help slave to boot from its memory space is master. They are different environments and requirements: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure SRIO switch system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to SRIO1 or SRIO2 by RCW. 3. RCW should configure the SerDes, SRIO interfaces correctly. 4. Slave must be powered on after master's boot. For the master module, need to finish these processes: 1. Initialize the SRIO port and address space. 2. Set inbound SRIO windows covered slave's u-boot image stored in master's NOR flash. 3. Master's u-boot image should be generated specifically by make xxxx_SRIOBOOT_MASTER_config 4. Master must boot first, and then slave can be powered on. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Document for the boot from SRIOLiu Gang
This document describes the implementation of the boot from SRIO, includes the introduction of envionment, an example based on P4080DS platform, an example of the slave's RCW, and the description about how to use this feature. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24powerpc/corenet_ds: Correct the compilation errors about ENVLiu Gang
When defined CONFIG_ENV_IS_NOWHERE, there will be some compilation errors: ./common/env_nowhere.o: In function `env_relocate_spec': ./common/env_nowhere.c:38: multiple definition of `env_relocate_spec' ./common/env_flash.o: ./common/env_flash.c:326: first defined here ./common/env_nowhere.o: In function `env_get_char_spec': ./common/env_nowhere.c:42: multiple definition of `env_get_char_spec' ./common/env_flash.o:./common/env_flash.c:78: first defined here ./common/env_nowhere.o: In function `env_init': ./common/env_nowhere.c:51: multiple definition of `env_init' ./common/env_flash.o:./common/env_flash.c:237: first defined here make[1]: *** [./common/libcommon.o] Error 1 make[1]: Leaving directory `./common' make: *** [./common/libcommon.o] Error 2 Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24powerpc/srio: Rewrite the struct ccsr_rioLiu Gang
Rewrite this struct for the support of two ports and two message units registers. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24powerpc/85xx:Fix lds for nand boot debug infoPrabhakar Kushwaha
Currently "u-boot", the elf file generated via u-boot-nand.lds does not contain required debug information i.e. .debug_{line, info, abbrev, aranges, ranges} into their respective _global_ sections. The original ld script line arch/powerpc/cpu/mpc85xx/start.o KEEP(*(.bootpg)) is not entirely correct because the start.o file is already processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will not process start.o again for bootpg. So Fix u-boot-nand.lds to generate these debug information. Signed-off-by: Anmol Paralkar <b07584@freescale.com> Signed-off-by: John Russo <John.Russo@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/p2041rdb: add env in NAND supportShaohui Xie
Add env in NAND support when boot from NAND. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/p2041rdb: add NAND and NAND boot supportShaohui Xie
New P2041RDB board will add a NAND chip, so add support for NAND and NAND boot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boardsYork Sun
P1010RDB and p1_pc_rdb_pc has incorrect configuration for CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING. Incorrect setting causes DDR failure in case of SPD absent. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/85xx:Avoid vector table compilation for nand_splPrabhakar Kushwaha
NAND SPL code never compile the vector table. So no need to setup interrupt vector table for NAND SPL. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/85xx:Fix IVORs addr after vector table relocationPrabhakar Kushwaha
After relocation of vector table in SDRAM's lower address, IVORs value should be updated with new handler addresses. As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs are updated with 0x100, 0x200,....f00 hard-coded values. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/85xx:Avoid hardcoded vector address for IVORsPrabhakar Kushwaha
For e500 and e500v2 architecturees processor IVPR address should be alinged on 64K boundary. in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be 64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may not point to an exception handler. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24powerpc/p1023rds: Disable nor flash node and enable nand flash nodeChunhe Lan
In the p1023rds, when system boots from nor flash, kernel only accesses nor flash and can not access nand flash with BR0/OR0; when system boots from nand flash, kernel only accesses nand flash and can not access nor flash with BR0/OR0. Default device tree nor and nand node should have the following structure: Example: nor_flash: nor@0,0 { #address-cells = <1>; #size-cells = <1>; compatible = "cfi-flash"; reg = <0x0 0x0 0x02000000>; bank-width = <2>; device-width = <1>; status = "okay"; partition@0 { label = "ramdisk"; reg = <0x00000000 0x01c00000>; }; } nand_flash: nand@1,0 { #address-cells = <1>; #size-cells = <1>; compatible = "fsl,p1023-fcm-nand", "fsl,elbc-fcm-nand"; reg = <0x2 0x0 0x00040000>; status = "disabled"; u-boot-nand@0 { /* This location must not be altered */ /* 1MB for u-boot Bootloader Image */ reg = <0x0 0x00100000>; read-only; }; } When booting from nor flash, the status of nor node is enabled and the status of nand node is disabled in the default dts file, so do not do anything. But, when booting from nand flash, need to do some operations: o Disable the NOR node by setting status = "disabled"; o Enable the NAND node by setting status = "okay"; Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24i2c:designware Turn off the ctrl when setting the speedArmando Visconti
The designware i2c controller must be turned off before setting the speed in IC_CON register, as stated in the section 6.3.1 of the dw_apb_i2c_db.pdf. Signed-off-by: Michel Sanches <michel.sanches@st.com> Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24i2c: Add support for designware i2c controllerVipin KUMAR
Earlier, a driver exists in the u-boot source for designware i2c interface. That driver was specific to spear platforms. This patch implements the i2c controller as a generic driver which can be used by multiple platforms The driver files are now renamed to designware_i2c.c and designware_i2c.h and these are moved into drivers/i2c folder for reusability by other platforms Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24sh: i2c: Add support I2C controller of SH7734Nobuhiro Iwamatsu
Renesas SH7734 has two I2C interfaceis. This supports these I2C. V5: - include i2c.h. - Add check of icsr bit polling logic. - Implement i2c_probe. V4: - Remove sh_i2c_dump_reg function. - Use puts() when there's no format. - Chnage check for I2C bus number. - Remove space before the semi-colon. V3: - Fix error for whitespace. V2: - Changed bit control to use the clr|set|clrsetbits_* functions. - Fix wrong comment style. - Add new line before for loop in i2c_read. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-23sandbox: Use the new run_command()Simon Glass
Now that run_command() handles both parsers, clean up sandbox to use it. This fixes a build error. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-23arm: restore fdt_fixup_ethernet call to do_bootm_linuxStephen Warren
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux for ARM. During the re-organization, the call to fdt_fixup_ethernet() was removed. I assume this was useful, so add it back. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com>
2012-04-23arm: fix bootm with device treeStephen Warren
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux() for ARM. During the re-organization, the code to pass the device tree to the kernel was removed. Add it back. This restores the ability to boot a kernel using device tree. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Allen Martin <amartin@nvidia.com> Tested-by: Allen Martin <amartin@nvidia.com>
2012-04-23Fix the behaviour of the 'run' commandTimo Ketola
If one command fails, 'run' command should terminate and not execute any remaining variables. Signed-off-by: Timo Ketola <timo@exertus.fi> Tested-by: Wolfgang Denk <wd@denx.de> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-22Blackfin: bfin_sdh: drop dos part hardcodeMike Frysinger
No other driver sets up the part type to DOS in their init, and it doesn't seem to be needed as `mmcinfo` and `mmc part` stll work, so drop it. Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22Blackfin: move gd/bd to bss by defaultMike Frysinger
We don't need these setup manually, so let the bss do the rest. On Blackfin systems, we clear the bss before executing any C code that would use these, so this should be fine. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22Blackfin: gd_t: relocate volatile markingsMike Frysinger
This makes Blackfin behave the same as other ports, and fixes many gcc warnings that show up with 4.5+: board.c:40:1: warning: optimization may eliminate reads and/or writes to register variables Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22board/adp-ag102: add configuration of adp-ag102Macpaul Lin
board: Add config file of board adp-ag102 Add adp-ag102 into boards.cfg Add adp-ag102 into MAINTAINERS doc: add README of ag102 Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22board/adp-ag102: add board specific filesMacpaul Lin
Add board specific files. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22nds32/ag102: add ag102 soc supportMacpaul Lin
Add lowlevel ag102 soc support. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22nds32/ag102: add header support of ag102 socMacpaul Lin
Add device address offsets header of ag102 soc. Add ag102 into mach-types.h. Add asm-offsets.c for helping convert C headers into asm. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-21Prepare v2012.04Wolfgang Denk
Also tiny style cleanup to tools/patman/README Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-21net: ll_temac: drop obsolete "NAMESIZE" defineStephan Linz
... after commit "net/miiphy/serial: drop duplicate NAMESIZE define" (sha1:f6add13) was applied. The building of the new LL TEMAC network driver fails with error below: xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize': xilinx_ll_temac.c:301: error: 'NAMESIZE' undeclared (first use in this function) xilinx_ll_temac.c:301: error: (Each undeclared identifier is reported only once xilinx_ll_temac.c:301: error: for each function it appears in.) Signed-off-by: Stephan Linz <linz@li-pro.net> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-21Add 'patman' patch generation, checking and submission scriptSimon Glass
What is this? ============= This tool is a Python script which: - Creates patch directly from your branch - Cleans them up by removing unwanted tags - Inserts a cover letter with change lists - Runs the patches through checkpatch.pl and its own checks - Optionally emails them out to selected people It is intended to automate patch creation and make it a less error-prone process. It is useful for U-Boot and Linux work so far, since it uses the checkpatch.pl script. It is configured almost entirely by tags it finds in your commits. This means that you can work on a number of different branches at once, and keep the settings with each branch rather than having to git format-patch, git send-email, etc. with the correct parameters each time. So for example if you put: in one of your commits, the series will be sent there. See the README file for full details. END Signed-off-by: Simon Glass <sjg@chromium.org>
2012-04-21eb_cpux9k2: add USB host support to boardJens Scharsig
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2012-04-21mmc: Fix warning if CONFIG_MMC_TRACE is enabledDirk Behme
Fix the warning mmc.c: In function 'mmc_send_cmd': mmc.c:87: warning: assignment from incompatible pointer type in case CONFIG_MMC_TRACE is enabled. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Andy Fleming <afleming@freescale.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
2012-04-21ehci-omap: fix for enabling the correct usb portJeroen Hofstee
This is just a patch for the problem reported here: http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor. "Looks like this is copy paste error from my side,(for port2/3 it should have been bypass for port2/3 rather its port1 set in bypass mode)" I only submit the patch since it is missing in 2012.04-rc3 while the twister board depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it. note: the twister boards still needs an additional `usb reset`, don't know why. U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38) AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz TAM3517 TWISTER Board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In: serial Out: serial Err: serial Die ID #746c0000000000000155dc1405011024 Net: DaVinci-EMAC, smc911x-0 Hit any key to stop autoboot: 0 twister => usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Govindraj.R <govindraj.raja <at> ti.com> Acked-by: Tom Rini <trini@ti.com>
2012-04-21fdt: avoid bad MAKEALL statusWolfgang Denk
Current versions of dtc always print a message like DTC: dts->dtb on file "dt.dtb.tmp" which cannot even be suppressed with "-qqq". To avoid incorrect MAKEALL status, we manually filter out this message. This is a bit complicated, as we have to make sure to set a correct return code. Also, get rid of the temp file: dtc accepts "-" for stdin. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-21fdt: fix out of tree builds with DT supportWolfgang Denk
Fix: FATAL ERROR: Couldn't open "../arch/arm/dts/tegra20.dtsi": No such file or directory Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-21GCC4.6: Squash warnings in onenand_base.cWolfgang Denk
Fix gcc 4.6 build warnings: onenand_base.c: In function 'onenand_probe': onenand_base.c:2577:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2012-04-19CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logicMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZEMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: scottwood@freescale.com
2012-04-19CMD: Fix typo CMD_FSL -> CMD_MFSL in readmeMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: vapier@gentoo.org Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUMMarek Vasut
Fix typo Signed-off-by: Marek Vasut <marex@denx.de> Cc: Kyle.D.Moffett@boeing.com Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19CMD: Remove CMD_LOG, it's unusedMarek Vasut
$ git grep CMD_LOG include/configs/kilauea.h:#define CONFIG_CMD_LOG include/configs/lwmon5.h:#define CONFIG_CMD_LOG include/configs/makalu.h:#define CONFIG_CMD_LOG include/configs/quad100hd.h:#undef CONFIG_CMD_LOG include/configs/zeus.h:#define CONFIG_CMD_LOG Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19CMD: Fix typo KGBD -> KGDB on debris boardMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: dogoil@etinsys.com Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19CMD: Drop CONFIG_CMD_EMMC, it's not usedMarek Vasut
$ git grep CMD_EMMC include/configs/u8500_href.h:#define CONFIG_CMD_EMMC Signed-off-by: Marek Vasut <marex@denx.de> Cc: dirk.behme@googlemail.com Cc: helmut.raiger@hale.at Cc: john.rigby@linaro.org Cc: vapier@gentoo.org
2012-04-19CMD: Drop CONFIG_CMD_DFL, it's not usedMarek Vasut
$ git grep CMD_DFL board/atc/ti113x.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \ board/atc/ti113x.c: pci_writew (s, PCI_COMMAND, CMD_DFLT); board/cpc45/pd67290.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \ board/cpc45/pd67290.c: pci_writew (s, PCI_COMMAND, CMD_DFLT); drivers/pcmcia/i82365.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \ drivers/pcmcia/i82365.c: pci_writew (s, PCI_COMMAND, CMD_DFLT); include/configs/MBX.h:#define CONFIG_CMD_DFL include/configs/MigoR.h:#define CONFIG_CMD_DFL include/configs/digsy_mtc.h:#define CONFIG_CMD_DFL include/configs/ms7722se.h:#define CONFIG_CMD_DFL include/configs/ms7750se.h:#define CONFIG_CMD_DFL include/configs/r2dplus.h:#define CONFIG_CMD_DFL include/configs/sh7757lcr.h:#define CONFIG_CMD_DFL include/configs/sh7785lcr.h:#define CONFIG_CMD_DFL Signed-off-by: Marek Vasut <marex@denx.de> Cc: Pfister_Werner@intercontrol.de Cc: iwamatsu@nigauri.org Cc: nobuhiro.iwamatsu.yj@renesas.com Cc: vapier@gentoo.org Cc: wd@denx.de Cc: yoshihiro.shimoda.uh@renesas.com Acked-by: Anatolij Gustschin <agust@denx.de> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-04-19CMD: Drop CMD_DCR, it's not usedMarek Vasut
$ git grep CMD_DCR include/configs/ep8260.h:#undef CONFIG_CMD_DCR Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19CMD: Drop CMD_CAN, it's not usedMarek Vasut
$ git grep CMD_CAN include/configs/jadecpu.h:#define CONFIG_CMD_CAN Signed-off-by: Marek Vasut <marex@denx.de> Cc: Matthias Weisser <weisserm@arcor.de>
2012-04-19CMD: Remove CMD_AUTOSCRIPT, it's not usedMarek Vasut
$ git grep AUTOSCRIPT include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19AT91: Drop AT91_SPIMUX command from cmd_allMarek Vasut
$ git grep AT91_SPIMUX include/config_cmd_all.h:#define CONFIG_CMD_AT91_SPIMUX /* AT91 MMC/SPI Mux Support */ It isn't used anywhere it seems. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-18Prepare v2012.04-rc3Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-18Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
* 'master' of git://git.denx.de/u-boot-sh: sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT sh: Fix rsk7264 pin setup for on-board ethernet
2012-04-18sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INITNobuhiro Iwamatsu
When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT. The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit (git 2.34.1) at 2024-12-26 12:15:48 +0000