summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-01-30powerpc/t4240qds: Update IFC timing for NOR flashYork Sun
Relax parameters to give address latching more time to setup. Tighten parameters to make it overall faster. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30boards/T4240qds:Fix IFC AMASK init as per FPGA register spacePrabhakar Kushwaha
T4240QDS's QIXIS FPGA has 4k register space size and IFC controller's Address Mask Registers is initialised 64K size. So Fix the Address Mask Register initilisation as 4K Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30board/T4240qds:Fix TLB and LAW size of NAND flashPrabhakar Kushwaha
The internal SRAM of Freescale's IFC NAND machine is of 64K and controller's Address Mask Registers is initialised with the same. So Update TLB and LAW size of NAND flash accordingly. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/mpc85xx: Reserve default boot pageYork Sun
The boot page in memory is already reserved so OS won't overwrite. As long as the boot page translation is active, the default boot page also needs to be reserved in case the memory is 4GB or more. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/t4qds: move VSC3316 config data from t4qds.h to t4qds.cTimur Tabi
Static variables should be defined in C files, not header files, because otherwise every C file that #includes the header file will generate a duplicate of the variables. Since the vsc3316_xxx[] arrays are only used by t4qds.c anyway, just put the variables there. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/p2041: move Lanes mux to board early initShaohui Xie
Lanes mux currently is configured in eth.c when initializing FMAN ethernet ports, but SRIO and PCIe also need lanes mux, so we move the lanes mux to p2041rdb.c which implements a board-specific initialization and will be called at early stage. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-29Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2013-01-29Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxTom Rini
2013-01-29Remove unused CONFIG_SYS_I2C_BUS[_SELECT]Michael Jones
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere outside of config files. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-01-29i2c: mxs: Staticize the functions in the driverMarek Vasut
The local functions in the mxs i2c driver are not marked static, make it so. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2013-01-28mx23evk: Add initial board supportOtavio Salvador
The following features are supported: * 128 MB DDR1 SDRAM * DUART * SD/MMC Card Socket Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28mx23_olinuxino: Add default environmentOtavio Salvador
This adds a default environment with support for MMC booting. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-01-28mxs: mmc: mx23_olinuxino: Add MMC supportMarek Vasut
Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mxs: mmc: Fix the MMC driver for MX23Marek Vasut
The MX23 has different layout of DMA channels. Fix the MMC driver to support MX23. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mxs: mmc: Allow overriding default card detect implementationMarek Vasut
Some MXS based boards do not implement the card-detect signal. Allow user to specify alternate card-detect implementation. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mxs: mmc: Fix MMC reset on iMX23Otavio Salvador
This does the same reset mask as done in v3.7 Linux kernel code. The block is properly configured for MMC operation that way. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mxs: ssp: Add SSP registers map for MX23Marek Vasut
The MX23 SSP register layout differs from MX28 in certain bits, adjust the register layout accordingly. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mxs: dma: Fix APBH DMA driver for MX23Marek Vasut
The MX23 has less channels for the APBH DMA, sligtly different register layout and some bits in those registers are placed differently. Reflect this in the driver. This patch fixes MMC/DMA issue on MX23. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-28mx6qsabrelite: search mii phy address 4-7Troy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: get phydev before fec_probeTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: only call phy_connect in fec_probeTroy Kisky
This allows us to create the phydev before calling fec_probe in later patch. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: use fec_set_dev_name to set nameTroy Kisky
This allows us to create the phydev before calling fec_probe in later patch. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28phy: add phy_find_by_mask/phy_connect_devTroy Kisky
It is useful to be able to try a range of possible phy addresses to connect. Also, an ethernet device is not required to use phy_find_by_mask leading to better separation of mii vs ethernet, as suggested by Andy Fleming. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multiTroy Kisky
Having only one call to fec_probe will ease the changing of its parameters. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: change fec_mii_setspeed parameterTroy Kisky
Only the hardware ethernet registers are needed for this function, so don't pass the more general structure. I'm trying to separate MII and fec. This also fixes MX28 fec_mii_setspeed use on secondary ethernet port This was found by inspection of the code and should be checked on real hardware. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28net: fec_mxc: delete CONFIG_FEC_MXC_MULTITroy Kisky
It is more logical to test for CONFIG_FEC_MXC_PHYADDR to determine whether to define the function fecmxc_initialize. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28doc/README.fec_mxc: add documentationTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28mxs: Use __weak annotation to simplify codeFabio Estevam
Using the __weak annotation can make the code cleaner. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2013-01-28tools: imximage: Let .name field be more genericFabio Estevam
Since this structure is not i.MX5x specific, remove the '5x' to make it more generic. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28mx6qsabre_common: Let mmc partition be board specificFabio Estevam
commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h to store the mmc partition, but in order for it to have effect we should place it into 'mmcpart' variable. Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28mx6qsabreauto: enable USB host interfaceKnut Wohlrab
The USB host interface is routed to plug USB1/J30 on the mother board. Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>
2013-01-28mxs: Boost the memory power supplyMarek Vasut
The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-01-27MIPS: start.S: don't save flush_cache parameters in advanceGabor Juhos
Saving the parameters in advance unnecessarily complicates the code. The destination address is already saved in the 's2' register, and that register is not clobbered by the copy loop. The size of the copied data can be computed after the copy loop is done. Change the code to compute the size parameter right before calling flush_cache, and set the destination address parameter in the delay slot of the actuall call. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27MIPS: start.S: simplify relocation offset calculationGabor Juhos
The current code uses four instructions and a temporary register to calculate the relocation offset and to adjust the gp register. The relocation offset can be calculated directly from the CONFIG_SYS_MONITOR_BASE constant and from the destination address. The resulting offset can be used to adjust the gp pointer. This approach makes the code a bit simpler because it needs two instructions only. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27MIPS: start.S: save reused arguments earlier in relocate_codeGabor Juhos
Save the reused parameters at the beginning of the 'relocate_code' function. This makes the function a bit more readable. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27MIPS: start.S: set sp register directlyGabor Juhos
The current code uses two instructions to load the stack pointer into the 'sp' register. This results in the following assembly code: 468: 3c088040 lui t0,0x8040 46c: 251d0000 addiu sp,t0,0 The first instuction loads the stack pointer into the 't0' register then the value of the 'sp' register is computed by adding zero to the value of the 't0' register. The same issue present on the 64-bit version as well: 56c: 3c0c8040 lui t0,0x8040 570: 659d0000 daddiu sp,t0,0 Change the code to load the stack pointer directly into the 'sp' register. The generated code is functionally equivalent to the previous version but it is simpler. 32-bit: 468: 3c1d8040 lui sp,0x8040 64-bit: 56c: 3c1d8040 lui sp,0x8040 Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27MIPS: start.S: fix boundary check in relocate_codeGabor Juhos
The loop code copies more data with one than necessary due to the 'ble' instuction. Use the 'blt' instruction instead to fix that. Due to the lack of suitable hardware the Xburst specific code is compile tested only. However the change is quite obvious. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22MIPS: start{, 64}.S: fill branch delay slots with NOP instructionsGabor Juhos
The romReserved and romExcHandle handlers are accessed by a branch instruction however the delay slots of those instructions are not filled. Because the start.S uses the 'noreorder' directive, the assembler will not fill the delay slots either, and leads to the following assembly code: 0000056c <romReserved>: 56c: 1000ffff b 56c <romReserved> 00000570 <romExcHandle>: 570: 1000ffff b 570 <romExcHandle> In the resulting code, the second branch instruction is placed into the delay slot of the first branch instruction, which is not allowed on the MIPS architecture. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22MIPS: convert IO port accessor functions to 'static inline'Gabor Juhos
The currently used 'extern inline' directive causes the following compiler warnings if CONFIG_SWAP_IO_SPACE is defined: <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc_p' which is not static [enabled by default] <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl_p' which is not static [enabled by default] <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc' which is not static [enabled by default] <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl' which is not static [enabled by default] <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc_p' which is not static [enabled by default] <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw_p' which is not static [enabled by default] <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc' which is not static [enabled by default] <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw' which is not static [enabled by default] <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc_p' which is not static [enabled by default] <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl_p' which is not static [enabled by default] <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc' which is not static [enabled by default] <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl' which is not static [enabled by default] <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc_p' which is not static [enabled by default] <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw_p' which is not static [enabled by default] <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc' which is not static [enabled by default] <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw' which is not static [enabled by default] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22MIPS: use inline directive for __in*s functionsGabor Juhos
All other IO accessor functions are using the 'inline' directive. Use that also for the __in*s to make it consistent with the other variants. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22imximage.cfg: run files through C preprocessorTroy Kisky
The '#' used as comments in the files cause the preprocessor trouble, so change to /* */. The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile .gitignore was updated to ignore .cfgtmp files. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-21mxs: Add MX23 quirks into the clock codeOtavio Salvador
The MX23 has different handling of the SSP clock and GPMI NAND clock sources, add necessary quirks into the clock code to properly handle these. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21woodburn: Set Write Protection GPIO as inputFabio Estevam
Set Write Protection GPIO as input. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-21mxs: Add MX23 olinuxino board supportMarek Vasut
This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mxs: Linux uses ttyAMA0 as DUARTMarek Vasut
Replace use of ttyAM0 with ttyAMA0 as default serial console. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mxs: Fix the memory init for MX23Otavio Salvador
The memory init is slightly different on MX23, thus split the memory init for mx23 and mx28 into different functions. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mxs: Add function to ungate the power block on MX23Marek Vasut
The power block on MX23 must first be ungated before it can be operated. Add function to MXS power init that ungates it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mmc: Limit the number of used SSP ports on MX23Marek Vasut
The MX23 can only use two SSP ports. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andy Fleming <afleming@freescale.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mx23: config: Enable mxsboot tool for i.MX23 based boardsOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2013-01-21mx23: config: Enable building of u-boot.sb binaryOtavio Salvador
For i.MX23 we need to pass imx23 as elftosb param. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit (git 2.34.1) at 2025-01-24 23:28:04 +0000