| Age | Commit message (Collapse) | Author |
|---|
|
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
|
|
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Move CONFIG_DEFAULT_DEVICE_TREE from board config
directly to defconfig.
This patch removes compilation warning:
include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE"
redefined [enabled by default]
#define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
Commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs)
collected the default values of CONFIG_SYS_CPU into arch/arm/Kconfig.
This commit moves "armv8" to there for consistency.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Georges Savoundararadj <savoundg@gmail.com>
|
|
This commit adds "select CPU_V7" for some new boards that were not
covered by commit 2e07c249a67e
(kconfig: arm: introduce symbol for ARM CPUs).
Redundant "SYS_CPU" defines and "string" directives should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Georges Savoundararadj <savoundg@gmail.com>
|
|
There is no board with CPU "arm_intcm".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
|
|
Precisely, these boards are SH4A rather than SH4.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Now each board selects one of CONFIG_CPU_SH2, CONFIG_CPU_SH3,
CONFIG_CPU_SH4, so let's move CONFIG_SYS_CPU definition to
arch/sh/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4
to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A,
CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because
arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The current prompts were added by a conversion tool
based on board directory names when switching to Kconfig.
Use better prompts mostly taken from from arch/sh/boards/*
of Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The Makefiles call the respective interpreter explicitly, but this makes
it easier to use the scripts manually.
(This commit follows commit 06ed5c2bfaca of Linux Kernel)
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Adjust the text to mention that rev C of the board is also supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.
SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.
The result is that the selected boot device is not used across all
the boot stages.
Update spl_boot_device() to look at gpr9 when necessary.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
When DEBUG is set, output memory region used for malloc().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
size_t is the canonical type to represent variables that contain a size.
Use it instead of signed integer. Physical addresses can be larger than
32-bit, so use a more appropriate type for them as well. phys_addr_t is
a type that is 32-bit on systems that use 32-bit addresses and 64-bit if
the system is 64-bit or uses a form of physical address extension to use
a larger address space on 32-bit systems. Using these types the same API
can be implemented on a wider range of systems.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove two gratuituous blank lines, uses u32 (instead of int) as the
type for values that will be written to a register, moves the beginning
of the variable declaration section to a separate line (rather than the
one with the opening brace) and keeps the function signature on a single
line where possible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
|
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
This reverts commit 1e96220a5687efae2aed45ce56e143336c40d0a7.
Remove duplicated vxworks.h header.
The same change was done by
"ARM: prevent compiler warnings from bootm.c"
(sha1: 8d196e52b58d1e50a80c2f5067b201cda521c75c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
This commit merges
arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c
to
arch/arm/cpu/armv7/uniphier/board_postclk_init.c
Because PH1-Pro4 does not have the BCU block, add __weak to
bcu_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.
With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack. In some use cases, the system hangs up
with stack over-flow.
Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code. This commit adds a simple
macro that is available in asm code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
FAT-formated USB storage device access is available.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
This commit adds register defines of MIO (Media I/O) block
of UniPhier platform. This file is necessary to control
the reset signals of the USB cores.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
These IO pins are necessary for port power control and
over current detect.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
If a support card is attached to the main board, the on-board
SMSC9118 LAN controller is available. It must be kept in reset
state for a while on start-up.
When the board is kicked via a debbuger rather than pushing the
hardware reset button, on-board chips are not reset; in this case
the reset signals should be asserted by software.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.
Also, remove unnecessary inclusion of <common.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Add a defconfig and Kconfigury for the Digilent ZYBO board.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds config support needed for ZYBO target and has
been tested on Rev. B ZYBO hardware.
Signed-off-by: Tinghui Wang <steven.wang@digilentinc.com>
[PC changes:
* Dropped boards.cfg change (rebase conflict)
* Dropped custom u-boot env
* Added DTS
* Misc forward-porting changes
]
Signed-off-by: Peter Crosthwiate <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It's a Zynq board similar in design to the currently supported ones.
512MB of RAM and UART1 is used.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The latest Xilinx tools generate ps7_init files that are explicitly
available under GPL. Change the makefile to allow drop in of those files
for building the SPL.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-and-tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
|
|
|
|
This patch adds support for comments in the input to mkenvimage, i.e. in
the environment source: All lines starting with a # in the firs column
will be ignored.
Additionally empty lines will also be ignored.
Signed-off-by: Dominik Muth <dominik.muth@bkvibro.com>
|
|
In a message from Wolfgang Denk highlighting warnings from cppcheck,
the patch will address those that are correctly diagnosed. Some are
false-positives:
> [fs/zfs/zfs.c:937]: (error) Memory leak: l
dmu_read() allocates "l" if successful, so error-case should not free
it.
> [fs/zfs/zfs.c:1141]: (error) Memory leak: dnbuf
dmu_read() allocates "dnbuf" if successful, so error-case should not
free it.
> [fs/zfs/zfs.c:1372]: (error) Memory leak: osp
zio_read() allocates "osp" if successful, so error-case should
not free it.
> [fs/zfs/zfs.c:1726]: (error) Memory leak: nvlist
int_zfs_fetch_nvlist() allocates "nvlist" if successful, so error-case
should not free it.
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
|
|
cppcheck reports:
[board/esd/common/auto_update.c:458]: (error) Uninitialized variable: cnt
The variable is not really used anywhere, so remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
|
|
cppcheck reports:
[arch/arm/cpu/arm926ejs/mxs/timer.c:96]: (error) Uninitialized
variable: now
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Change clock of SCIF for Alt board is used to external clock.
This changes to using external clock.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
|
