summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-09-07ARM: armv7: move ARMV7_PSCI_NR_CPUS to KconfigMasahiro Yamada
Move this option to Kconfig and set its default value to 4; this increases the number of supported CPUs for some boards. It consumes 1KB memory per CPU for PSCI stack, but it should not be a big deal, given the amount of memory used for the modern OSes. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: armv7: move CONFIG_ARMV7_PSCI to KconfigMasahiro Yamada
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms can select. Then, move CONFIG_ARMV7_PSCI, which is automatically enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: armv7: guard memory reserve for PSCI with #ifdef CONFIG_ARMV7_PSCIMasahiro Yamada
If CONFIG_ARMV7_NONSEC is enabled, the linker script requires CONFIG_ARMV7_PSCI_NR_CPUS regardless of CONFIG_ARMV7_PSCI. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: tegra: remove wrong dependency on SPL_BUILDMasahiro Yamada
SPL_BUILD is not a CONFIG in Kconfig, so !SPL_BUILD is always true. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-06omap3_pandora: Switch to using "load" command to load the autoboot script.Vagrant Cascadian
CONFIG_CMD_FS_GENERIC is enabled; use it to load the autoboot script, rather than first attempting with fatload and falling back to ext2load. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Grazvydas Ignotas <notasas@gmail.com>
2016-09-06omap3_pandora: Fix mmc loading of autoboot script to use correct syntax.Vagrant Cascadian
fatload/ext2load both require that the device and partition be specified after specifying the device type. Specify the first partition on mmc device 0, which is the only mmc device currently configured on the pandora. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Grazvydas Ignotas <notasas@gmail.com>
2016-09-06TI: Rework SRAM definitions and maximumsTom Rini
On all TI platforms the ROM defines a "downloaded image" area at or near the start of SRAM which is followed by a reserved area. As it is at best bad form and at worst possibly harmful in corner cases to write in this reserved area, we stop doing that by adding in the define NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this. At current we define the end of scratch space at 0x228 bytes past the start of scratch space this this gives us a lot of room to grow. As these scratch uses are non-optional today, all targets are modified to respect this boundary. Tested on OMAP4 Pandaboard, OMAP3 Beagle xM Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: "B, Ravi" <ravibabu@ti.com> Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: "Kipisz, Steven" <s-kipisz2@ti.com> Cc: Daniel Allred <d-allred@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
2016-09-06omap3logic: Fix PBIAS BugAdam Ford
The PBIAS fixing is done in the MMC driver, and doing it in the the board file conflicts with the driver causing intermittent hangs on reboot. Remove this from the board file and let the driver do it. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06README: add cmd directory descriptionXu Ziyuan
All of the command files have moved to cmd directory, add description to Directory Hierarchy. Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06board/BuR/common: increase NET_RETRY_COUNT to 10Hannes Schmelzer
Sometimes boards may need more time to become stable network connection due to several reasons: - phy speed - link-partner (switch) Therefore we increase the retry-count to 10 for making sure that network connection works always. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06configs: am4xhs: Modify SPL load address to fix UART boot issueMadan Srinivas
An issue in the TI secure image generation tool causes the ROM to load the SPL at a different load address than what is specified by CONFIG_ISW_ENTRY_ADDR while doing a peripheral boot on HS devices. This causes the SPL to fail on secure devices during peripheral boot. The TI secure image generation tool has been fixed so that the SPL will always be loaded at 0x403018E0 by the ROM code for both peripheral and memory boot modes. Signed-off-by: Madan Srinivas <madans@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06ARM: AM57xx: Enable post-processing of FIT artifacts loaded by U-BootAndreas Dannenberg
Enable the platform-specific post-processing of FIT-extracted blobs such as Kernel, DTB, and initramfs on TI AM57xx high-security (HS) devices which will ultimately invoke a ROM-based API call that performs secure processing such as blob authentication. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06ARM: DRA7xx: Enable post-processing of FIT artifacts loaded by U-BootAndreas Dannenberg
Enable the platform-specific post-processing of FIT-extracted blobs such as Kernel, DTB, and initramfs on TI DRA7xx high-security (HS) devices which will ultimately invoke a ROM-based API call that performs secure processing such as blob authentication. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06ARM: AM43xx: Enable post-processing of FIT artifacts loaded by U-BootAndreas Dannenberg
Enable the platform-specific post-processing of FIT-extracted blobs such as Kernel, DTB, and initramfs on TI AM43xx high-security (HS) devices which will ultimately invoke a ROM-based API call that performs secure processing such as blob authentication. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06spl: Rework image header parse to allow abort on raw image and os bootPaul Kocialkowski
This reworks spl_set_header_raw_uboot to allow having both os boot (which comes with a valid header) and aborting when no valid header is found (thus excluding raw u-boot.bin images). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06regulator: fixed: obey startup delayJohn Keeping
When enabling a fixed regulator, it may take some time to rise to the correct voltage. If we do not delay here then subsequent operations will fail. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06tools: moveconfig: add --spl option to move options for SPL buildMasahiro Yamada
Prior to this commit, the tool could not move options guarded by CONFIG_SPL_BUILD ifdef conditionals because they do not show up in include/autoconf.mk. This new option, if given, makes the tool parse spl/include/autoconf.mk instead of include/autoconf.mk, which is probably preferred behavior when moving options for SPL. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06tools: moveconfig: warn loudly if moved option has no entry in KconfigMasahiro Yamada
Currently, the tool gives up moving an option quietly if its entry was not found in Kconfig. If the option is not defined in the config header in the first place, it is no problem (as the Kconfig entry may have been hidden by reasonable "depends on"). However, if the option is defined in the config header, the missing Kconfig entry is a sign of possible behavior change. It is highly recommended to manually check if the option has been moved as expected. In this case, let's add "suspicious" in the log and change the log color (if --color option is given) to make it stand out. This was suggested by Tom in [1]. [1] http://lists.denx.de/pipermail/u-boot/2016-July/261988.html Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-06tools: moveconfig: use sets instead of lists for failed/suspicious boardsMasahiro Yamada
The sets feature is handier for adding unique elements. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-06tools: moveconfig: remove document about deprecated error messageMasahiro Yamada
Since commit cc008299f852 ("tools: moveconfig: do not rely on type and default value given by users"), we do not have this error case. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-06meson: odroid-c2: enable Ethernet support through the device treeBeniamino Galvani
Remove the device definition from board file, update the driver with the new compatible property and update config with necessary options. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06pinctrl: add driver for meson-gxbb pin controllerBeniamino Galvani
Add a pin controller driver for Meson GXBB adapted from Linux kernel. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06arm: dts: update DTS files for meson-gxbb and odroid-c2Beniamino Galvani
Import DTS files and dt-bindings includes from Linux 4.8-rc1. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06pinctrl: generic: scan for "pins" and "groups" properties in sub-nodesBeniamino Galvani
In cases where the pins and groups definitions are in a sub-node, as: uart_a { mux { groups = "uart_tx_a", "uart_rx_a"; function = "uart_a"; }; }; pinctrl_generic_set_state_subnode() returns an error for the top-level node and pinctrl_generic_set_state() fails. Instead, return success so that the child nodes are tried. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-06image-fit: fix fit_image_load() OS checkAndreas Bießmann
Commit 62afc601883e788f3f22291202d5b2a23c1a8b06 introduced fpga image load via bootm but broke the OS check in fit_image_load(). This commit removes following compiler warning: ---8<--- In file included from tools/common/image-fit.c:1: /Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: warning: use of logical '||' with constant operand [-Wconstant-logical-operand] os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA || ^ ~~~~~~~~~~~~ /Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: note: use '|' for a bitwise operation os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA || ^~ | 1 warning generated. --->8--- Signed-off-by: Andreas Bießmann <andreas@biessmann.org> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2016-09-06serial: bcm283x_mu: Detect disabled serial deviceAlexander Graf
On the raspberry pi, you can disable the serial port to gain dynamic frequency scaling which can get handy at times. However, in such a configuration the serial controller gets its rx queue filled up with zero bytes which then happily get transmitted on to whoever calls getc() today. This patch adds detection logic for that case by checking whether the RX pin is mapped to GPIO15 and disables the mini uart if it is not mapped properly. That way we can leave the driver enabled in the tree and can determine during runtime whether serial is usable or not, having a single binary that allows for uart and non-uart operation. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06bcm2835_gpio: Implement GPIOF_FUNCAlexander Graf
So far we could only tell the gpio framework that a GPIO was mapped as input or output, not as alternative function. This patch adds support for determining whether a function is mapped as alternative. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2016-09-06warp7: Print secure/non-secure mode infoFabio Estevam
warp7 has two targets: - warp7_defconfig: boots in non-secure mode - warp7_secure_defconfig: boots in secure mode Print the mode that is being used to help users to easily identify which target is running on the board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp7: Use PARTUUID to specify the rootfs locationFabio Estevam
warp7 can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. Succesfully tested booting a NXP 4.1 and also a mainline kernel. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp7: Add a secure mode targetFabio Estevam
NXP kernel expects to boot in secure mode, so introduce warp7_secure_defconfig target which selects CONFIG_ARMV7_BOOT_SEC_DEFAULT. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mx6ul_14x14_ev: Enable the CCGR clocks earlierFabio Estevam
To be in the safe side we need to enable the CCGR clocks prior to calling arch_cpu_init(). Inspired by Tim Harvey's commit d783c2744f9 ("imx: ventana: fix boot to SD"). Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Tested-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6ul_14x14_evk: Adjust SPL DDR3 settingsFabio Estevam
Adjust DDR3 initialization done in SPL by comparing them against the NXP DCD table. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6ul_14x14_evk: Pass refsel and refr fields to avoid hangFabio Estevam
When running a NXP 4.1 kernel with U-Boot mainline on a mx6ul-evk, we observe a hang when going into the lowest operational point of cpufreq. This hang issue does not happen on the NXP U-Boot version. After comparing the SPL DDR initialization against the DCD table from NXP U-Boot, the key difference that causes the hang is the MDREF register setting: DATA 4 0x021B0020 0x00000800 ,which means: REF_SEL = 0 --> Periodic refresh cycle: 64kHz REFR = 1 ---> Refresh Rate - 2 refreshes So adjust the MDREF initialization for mx6ul_evk accordingly to fix the kernel hang issue at low bus frequency. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6: ddr: Allow changing REFSEL and REFR fieldsFabio Estevam
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and REFR fields of the MDREF register as 1 and 7, respectively for DDR3 and 0 and 3 for LPDDR2. Looking at the MDREF initialization done via DCD we see that boards do need to initialize these fields differently: $ git grep 0x021b0020 board/ board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800 board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800 board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800 So introduce a mechanism for users to be able to configure REFSEL and REFR fields as needed. Keep all the mx6 SPL users in their current REF_SEL and REFR values, so no functional changes for the existing users. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx7dsabresd: Directly write to register LDOGCTLFabio Estevam
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mx7dsabresd: Directly write to register LDOGCTLFabio Estevam
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06pico-imx6ul: Directly write to register LDOGCTLFabio Estevam
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06ARM: board: cm_fx6: fix mtd partition fixupChristopher Spinrath
ft_board_setup may return early in the case that the board revision cannot be obtained. In that case it is assumed that no revision specific correction in the fdt is neccessary. But the mtd partitions will not be fixed up either altough they are not revision specific. Move the call to fdt_fixup_mtdparts in front of the revision specific part to ensure that the partitions are fixed up even if the board revision cannot be obtained. While on it, fix a spelling mistake in a comment introduced by the same commit. Fixes: 62d6bac66038 ("ARM: board: cm_fx6: fixup mtd partitions in the fdt") Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
2016-09-06mx6ul_14x14_evk: don't use array for SD2 card detect padEric Nelson
Only a single pad is changed to change sdhc2_dat3 from an SDIO pin to and from GPIO4:5, so remove the array and use the imx_iomux_v3_setup_pad() routine. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp7: Modify fdt_file environment variableBreno Lima
Use imx7s-warp.dts as fdt_file because this is the name that upstream kernel will deploy. Signed-off-by: Breno Lima <breno.lima@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp: Fix RAM size runtime detectionFabio Estevam
Since commit a13d3757f7df ("warp: Use imx_ddr_size() for calculating the DDR size") warp board no longer boots. The reason for the breakage is that the warp board is using the DDR configuration from mx6slevk. A fundamental difference between warp and mx6slevk is that warp only uses one DDR chip select while mx6slevk uses two. The imx_ddr() function calculates the RAM size in runtime by reading the values of registers MDCTL and MDMISC. So in order to fix this warp boot issue, create a imximage DDR file specific to warp, where the MDCTL register is configured to only activates a single chip select. Reported-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Breno Lima <breno.lima@nxp.com>
2016-09-06warp7: Add PMIC supportVanessa Maegima
Add PMIC support. Tested by command "pmic PFUZE3000 dump". Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-09-06arm: imx: Add support for Advantech DMS-BA16 boardAkshay Bhat
Add support for Advantech DMS-BA16 board. The board is based on Advantech BA16 module which has a i.MX6D processor. The board supports: - FEC Ethernet - USB Ports - SDHC and MMC boot - SPI NOR - LVDS and HDMI display Basic information about the module: - Module manufacturer: Advantech - CPU: Freescale ARM Cortex-A9 i.MX6D - SPECS: Up to 2GB Onboard DDR3 Memory; Up to 16GB Onboard eMMC NAND Flash Supports OpenGL ES 2.0 and OpenVG 1.1 HDMI, 24-bit LVDS 1x UART, 2x I2C, 8x GPIO, 4x Host USB 2.0 port, 1x USB OTG port, 1x micro SD (SDHC),1x SDIO, 1x SATA II, 1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2 Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: u-boot@lists.denx.de Cc: sbabic@denx.de
2016-09-06mx7dsabresd: Print secure/non-secure mode infoFabio Estevam
mx7dsabresd has two targets: - mx7dsabresd_defconfig: boots in non-secure mode - mx7dsabresd_secure_defconfig: boots in secure mode Print the mode that is being used to help users to easily identify which target is running on the board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mtd: nand: mxs: fix cache alignment for cache lines >32Stefan Agner
Currently the command buffer gets allocated with a size of 32 bytes. This causes warning messages on systems with cache lines bigger than 32 bytes: CACHE: Misaligned operation at range [9df17a00, 9df17a20] Define command buffer to be at least 32 bytes, but more if cache line is bigger. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-09-06imx: ventana: enable splashscreen supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-09-06board: tbs2910: fix HDMI pre-console bufferSoeren Moch
HDMI output must be enabled very early to also enable the pre-console buffer Signed-off-by: Soeren Moch <smoch@web.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-09-06board: tbs2910: always enable usbkbdSoeren Moch
'usb start' is much faster now, so always enable usb keyboard Signed-off-by: Soeren Moch <smoch@web.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-09-06Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-09-06Merge git://git.denx.de/u-boot-nand-flashTom Rini