summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-03-22strmhz: Make hz unsigned to support greater than 2146 MHz clockEd Swarthout
For example, an input of 0x80000000 should print: 2147.484 instead of -2147.-483. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-22Introduce a new linker flag LDFLAGS_FINALHaiying Wang
commit 8aba9dceebb14144e07d19593111ee3a999c37fc Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS breaks the usage of --gc-section to build nand_spl. We still need linker option --gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes the --gc-sections to each uboot image. To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace PLATFORM_LDFLAGS in the Makefile of each nand_spl board. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2011-03-22Fix hash table deletion to prevent lost entriesPeter Barada
Use negative used value to mark deleted entry. Search keeps probing past deleted entries. Adding an entry uses first deleted entry when it hits end of probe chain. Initially found that "ramdiskimage" and "preboot" collide modulus 347, causing "preboot" to be inserted at idx 190, "ramdiskimage" at idx 191. Previous to this fix when "preboot" is deleted, "ramdiskimage" is orphaned. Signed-off-by: Peter Barada <peter.barada@logicpd.com> Tested-by: Wolfgang Denk <wd@denx.de>
2011-03-21Top config.mk: add include/config.mkJoakim Tjernlund
Seems to me that the top level config.mk should include the auto generated include/config.mk so that all Makefile's pickup those definitions. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2011-03-21net: ftmac100: update get_timer() usagesPo-Yu Chuang
Use get_timer() the same way as drivers/net/ftgmac100.c Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Reviewed-by: Macpaul Lin <macpaul@gmail.com> Tested-by: Macpaul Lin <macpaul@gmail.com>
2011-03-21net: ftmac100: remove unnecessary volatilesPo-Yu Chuang
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Reviewed-by: Macpaul Lin <macpaul@gmail.com> Tested-by: Macpaul Lin <macpaul@gmail.com>
2011-03-21mpc52xx, digsy_mtc_rev5: Fix Linux crash, if no Flash in bank 2Heiko Schocher
If no Flash is connected to cs1, Linux crashes, because reg entries are not correct adapted. Following fix is needed: - swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as flash bank 1 is on chipselect 0 and flash bank 2 on chipselect 1 - call fdt_fixup_nor_flash_size() from ft_board_setup() Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <hs@denx.de> cc: Werner Pfister <Pfister_Werner@intercontrol.de> cc: Detlev Zundel <dzu@denx.de>
2011-03-21Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk
2011-03-21Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2011-03-21UBI: Fix error code handling in ubi commandsStefan Roese
Some ubi commands returned negative error codes, resulting in the following error message on the prompt: "exit not allowed from main input shell." Negative error codes are not allowed. This patch now changes the UBI code to return positive error codes. Additionally "better" error codes are used, for example "ENOMEM" when no memory is available for the UBI volume creation any more. Also the output of some commands is enhanced: Before: => ubi read 100000 testvol 100000 Volume testvol found at volume id 0 read 1048576 bytes from volume 0 to 100000(buf address) => ubi write 100000 testvol 1000 Volume testvol found at volume id 0 After: => ubi read 100000 testvol 100000 Read 1048576 bytes from volume testvol to 00100000 => ubi write 100000 testvol 1000 4096 bytes written to volume testvol Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2011-03-16sh: Add KEEP order to start.o sectionNobuhiro Iwamatsu
The start.o section is changed by --gc-section option of ld. Of this using KEEP order, therefore, evade this problem. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-03-16sh: Add handling of CONFIG_SYS_NO_FLASH for board.cNobuhiro Iwamatsu
Some board of SH does not have flash memoy. This revises it to initialize Flash when CONFIG_SYS_NO_FLASH is not defined. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-03-16net: sh_eth: add support for SH7757's ETHERYoshihiro Shimoda
SH7757 has ETHER and GETHER. This patch supports EHTER only. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-03-15powerpc/85xx: Fix synchronization of timebase on MP bootKumar Gala
There is a small ordering issue in the master core in that we need to make sure the disabling of the timebase in the SoC is visible before we set the value to 0. We can simply just read back the value to synchronizatize the write, before we set TB to 0. Reported-by: Dan Hettena Tested-by: Dan Hettena Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-13mpc8[5/6]xx: Ensure POST word does not get resetJohn Schmoller
The POST word is stored in a spare register in the PIC on MPC8[5/6]xx processors. When interrupt_init() is called, this register gets reset which resulted in all POST_RAM POSTs not being ran due to the corrupted POST word. To resolve this, store off POST word before the PIC is reset, and restore it after the PIC has been initialized. Signed-off-by: John Schmoller <jschmoller@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-07fsl_esdhc: Correcting esdhc timeout counter calculationPriyanka Jain
- Timeout counter value is set as DTOCV bits in SYSCTL register For counter value set as timeout, Timeout period = (2^(timeout + 13)) SD Clock cycles - As per 4.6.2.2 section of SD Card specification v2.00, host should cofigure timeout period value to minimum 0.25 sec. - Number of SD Clock cycles for 0.25sec should be minimum (SD Clock/sec * 0.25 sec) SD Clock cycles = (mmc->tran_speed * 1/4) SD Clock cycles - Calculating timeout based on (2^(timeout + 13)) >= mmc->tran_speed * 1/4 Taking log2 both the sides and rounding up to next power of 2 => timeout + 13 = log2(mmc->tran_speed/4) + 1 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-06powerpc/85xx: Fix pixis_reset altbank mask on MPC8536DSMatthew McClintock
Currently, pixis_reset altbank does not work properly. This patch uses the correct mask to boot into the alternate bank. Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-05powerpc/85xx: Fix plat_mp_up() disabling of BPTR for CoreNet PlatformsEd Swarthout
Copying directly from ECM/PQ3 is not correct for how CoreNet based platforms handle boot page translation. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-05powerpc/corenet_ds: revise platform dependent parametersYork Sun
This patch revised clk_adjust and wrlvl_start timings for corenet_ds, based on testing on Virtium VL33B5163F-K9S and Kingston KVR1333D3Q8R9S/4G. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-05corenet_ds: pick the middle value for all tested timing parametersYork Sun
For DDR3 controller, the clk_adjust and wrlvl_start are platform-dependent. The best values should be picked up from the middle of all working combinations. This patch updates the table with confirmed values tested on Hynix dual-rank UDIMMs (HMT125U7BFR8C-H9) at 1300MT/s, 1200MT/s, 1000MT/s, 900MT/s, 800MT/s and Kingston quad-rank RDIMMs (KVR1333D3Q8R9S/4G) at 1300MT/s, 1200MT/s, 1000MT/s. Signed-off-by: York Sun <yorksun@freescale.com>
2011-03-05powerpc/mpc8xxx: Fix DDR3 timing_cfg_1 and sdram_mode registersYork Sun
The write recovery time of both registers should match. Since mode register doesn't support cycles of 9,11,13,15, we should use next higher number for both registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-22fsl_law: Fix LAW printing functionKumar Gala
We had an extra '0x' in the output of the LAWAR header that would cause output like: LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d intead of: LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-21ARM: Update mach-typesSandeep Paulraj
This commit updates the mach-types based on the latest in linus's head Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-21arm1136 relocation: Fix calculation of board_init_rFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-02-21arm1136: Fix NAND bootFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2011-02-21arm: get_sp() should always be compiledPo-Yu Chuang
get_sp() was incorrectly excluded if none of CONFIG_SETUP_MEMORY_TAGS CONFIG_CMDLINE_TAG CONFIG_INITRD_TAG CONFIG_SERIAL_TAG CONFIG_REVISION_TAG were defined. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-02-21Pantheon: Add Board Support for Marvell dkb boardLei Wen
DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with * Processor upto 806Mhz * LPDDR1/2 * x8/x16 SLC/MLC NAND * Footprints for eMMC & MMC x8 card With Peripherals: * Parallel LCD I/F * Audio codecs (88PM8607) * MIPI CSI-2 camera * Marvell 88W8787 802.11n/BT module * Marvell 2G/3G RF * Dual analog mics & speakers, headset jack, LED, ambient * USB2.0 HS host, OTG (mini AB) * GPIO, GPIO expander with DIP switches for easier selection * UART serial over USB, CIR This patch adds basic board support with DRAM and UART functionality Signed-off-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-02-21mvmfp: add MFP configuration support for PANTHEONLei Wen
This patch adds the Multiple Function Pin configuration support for Marvell PANTHEON SoCs Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21serial: add pantheon soc supportLei Wen
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21ARM: Add Support for Marvell Pantheon Familiy SoCsLei Wen
Pantheon Family processors are highly integrated SoCs based on Sheeva_88SV331x-v5 PJ1 cpu core. Ref: http://www.marvell.com/products/processors/communications/marvell_pantheon_910_920_pb.pdf SoC versions Supported: 1) PANTHEON920 (TD) 2) PANTHEON910 (TTC) Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21mv: seperate kirkwood and armada from common settingLei Wen
Since there are lots of difference between kirkwood and armada series, it is better to seperate them but still keep the most common file shared by all marvell platform in the mv-common configure file. This patch move the kirkwood only driver definitoin in mv-common to the <soc_name>/config.h. This patch is tested with compilation for armada100 and guruplug. Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21ARM: fix write*() I/O accessorsWolfgang Denk
Commit 3c0659b "ARM: Avoid compiler optimization for readb, writeb and friends." introduced I/O accessors with memory barriers. Unfortunately the new write*() accessors introduced a bug: The problem is that the argument "v" gets evaluated twice. This breaks code like used here (from "drivers/net/dnet.c"): for (i = 0; i < wrsz; i++) writel(*bufp++, &dnet->regs->TX_DATA_FIFO); Use auxiliary variables to avoid such problems. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Alexander Holler <holler@ahsoftware.de> Cc: Dirk Behme <dirk.behme@googlemail.com>
2011-02-21arm relocation: Fix calculation of board_init_rAlexander Stein
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
2011-02-21arm: Tegra2: Add support for NVIDIA Seaboard boardTom Warren
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21arm: Tegra2: Add support for NVIDIA Harmony boardTom Warren
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21serial: Add Tegra2 serial port supportTom Warren
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21arm: Tegra2: Add basic NVIDIA Tegra2 SoC supportTom Warren
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21mx31pdk: Make the full boot log visibleFabio Estevam
Use board_early_init_f so that the full boot log output can be displayed. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-02-21mx31pdk: Use the new relocation schemeFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-02-21EfikaMX: switch to MACH_TYPE_MX51_EFIKAMXLoïc Minier
Upstream linux moved from MACH_TYPE_MX51_LANGE51 to MACH_TYPE_MX51_EFIKAMX. Signed-off-by: Loïc Minier <loic.minier@linaro.org>
2011-02-19Fix compile warning in net/eth.cRemy Bohmer
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2011-02-19Fix build warnings in cmd_flash.cRemy Bohmer
These variables are only used in case CONFIG_SYS_NO_FLASH is NOT set: struct mtd_device *dev; struct part_info *part; u8 dev_type, dev_num, pnum; Signed-off-by: Remy Bohmer <linux@bohmer.net>
2011-02-19USB-RNDIS: Send RNDIS state on disconnectingVitaly Kuzmichev
Add waiting for receiving Ethernet gadget state on the Windows host side before dropping pullup, but keep it for debug. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB: Add USB RNDIS gadget protocolVitaly Kuzmichev
Port USB gadget RNDIS protocol support from linux-2.6.26 (.27 gadget stack actually has composite drivers). Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: Move struct declaration before its useVitaly Kuzmichev
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: Port struct net_device_statsVitaly Kuzmichev
Port struct net_device_stats and statistics collecting needed for RNDIS protocol. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: handle interrupt after dropped pullupVitaly Kuzmichev
Disconnecting USB gadget with pending interrupt may cause its wrong handling in the next time when interface will be started again (especially actual for RNDIS). This interrupt may force the gadget to queue unexpected response before setup stage. Despite the fact that such interrupt handled after dropped pullup also may add pending response, this will not bring to any issues due to usb_ep_disable (which clears the queue) called on gadget unregistering. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19Add support for ASIX AX88772 USB 2.0 10/100Mbit Ethernet AdaptorSimon Glass
Driver originally written by NVIDIA Corporation, modified to handle odd-length packets. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-02-19Add USB host ethernet adapter supportSimon Glass
This adds support for using USB Ethernet dongles in host mode. This is just the framework - drivers will come later. A new config option called CONFIG_USB_HOST_ETHER can be defined in board config files to switch this on. The was originally written by NVIDIA and was cleaned up for release by the Chromium authors. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-02-19Fix EHCI usb submit timeout and unify with OHCISimon Glass
Changed both to use a common timeout for URB submission, since they were using different values and EHCI's was too short. Also fixed EHCI to actually check if urb submission succeeded, rather than silently continuing into the weeds. Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82 Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-26 05:15:10 +0000