summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-02-15Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2019.04-rc2 xilinx: - Start to use distro boot commands first - Setup fdtfile on ZynqMP - Move mac addr eeprom read to common location - Convert to OF_SEPARATE - Switch all board to DM_I2C - Some DT syncs i2c: - Remove !DM_I2C zynq driver versal: - Enable some more features - Add mini configurations
2019-02-15Merge tag '2019.01-next' of https://github.com/mbgg/u-bootTom Rini
- add compute module 3+ - fix 64 bit warning in bmp command
2019-02-15imx: cpu.c: give access to reset cause in splMax Krummenacher
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR register content intact so that U-Boot proper can evaluated the reset_cause again should this be needed. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-02-15imx: serial_mxc: disable ri and dcd irq in dte modeMax Krummenacher
If the UART is used in DTE mode the RI and DCD bits in UCR3 become irq enable bits. Both are set to enabled after reset and both likely are pending. Disable the bits to prevent an interrupt storm when Linux enables the UART interrupts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-02-15ARM: dts: i.MX6Q, i.MX6QDL: fix address/size-cells warningsMarcel Ziswiler
This fixes the following warnings: arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /clocks: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@02100000/mipi@021e0000: unnecessary #address-cells/ #size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02400000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02400000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02800000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02800000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-02-15imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+)Tim Harvey
device-tree paths should never be used that reference node addresses making an assumption about leading zeros. They should not be there per the device-tree specification however they have been there until Linux 4.15 when they were removed via kernel commit 8dccafaa281aa1d240a58bbcdff338aec114a021. This fixes various issues which will occur when using Linux 4.15+ that are being fixed up on a per model per PCB revision basis such as: - enabling MMC UHS-I on board revisions that support it - enabling PWM based on hwconfig - fixing PCIe reset on GW552x - removing cpu external watchdog reset on boards that do not support it - populate PCI dt nodes based on PCI scan in order to fix GW16082 interrupt mapping and inject MAC address for PCI based GbE Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: gw5904/gw5909: disable RS485Tim Harvey
The GW5904/GW5909 have a SP33E multi-protocol serial transceiver which we want to configure to RS232 by default (by de-asserting RS485_EN) Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5901/GW5902Tim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5909Tim Harvey
The GW5909 is a small single board computer based on the i.MX6DL SoC with the same peripheral set as the GW5904 but with half the DRAM loaded and an additional RS232 transceiver off UART2. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5908Tim Harvey
The GW5908 is a small single board computer based on the i.MX6DL SoC with the same peripheral set as the GW530x but with 1GiB density DRAM (64bit 512MiB). Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5907Tim Harvey
The GW5907 is a small single board computer based on the i.MX6DL SoC with the following peripheral set: - DDR3 memory (512MB default) - 1x GigE (i.MX6 FEC) - Gateworks System Controller Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5906Tim Harvey
The GW5906 is a GW552x with mechanical and power supply connector differences. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add i2c detect for all LVDS displaysTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: skip nand init for nandless boardsTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for Z101WX01 LVDS displayTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: add support for GW5905Tim Harvey
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the following peripheral set: - eMMC flash (boot device) - microSD expansion - LVDS display connector for off-board 3D+1C with PWM backlight and I2C based touch controller - MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640) - ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART) - ublox ZOE-M8Q GPS - LSM9DS1 9-DOF IMU - 1x 1-lane miniPCIe socket with USB 2.0 - Gateworks System Controller - Audio jack with TLV320AIC Audio Codec, Speaker AMP and TSA227E Headphone detect - MAX8607 3-mode LED camera flash - DECT ULE module - FUSB302 USB-C PD and ISL9238 Battery charger Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: remove setup of I2C3 from SPLTim Harvey
Do not setup I2C3 in the SPL for Ventana as some devices on that bus (aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until they are put into reset. Removing the setup of I2C3 from the SPL allows the board-specific GPIO to be configured to take care of putting codecs in reset prior to U-Boot setting up I2C3. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: do not iomux UART1Tim Harvey
The only UART that is garunteed on Ventana boards is UART2 (serial-console). Remove UART1 pinmux as that it is not consistent across all Ventana boards and U-Boot doesn't need it. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15imx: ventana: mv88e61xx change LED configurationTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI supportAbel Vesa
With DM and FIT enabled in SPL, there is an sram overflow. By disabling CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all' for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabresd: Remove the enet reset gpio handlingAbel Vesa
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi and get rid of the enet reset gpio handling from the board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabresd: Remove non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabresd board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15configs: mx6sabresd: Add DM_SPI_FLASH necessary configsAbel Vesa
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabreauto: Remove the non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabreauto board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15configs: mx6sabreauto: Add DM_SPI_FLASH necessary configsAbel Vesa
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabreauto. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabreauto: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabreauto. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabresd: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabresd. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15configs: mx6sabresd: Add SPL FIT and DM supportAbel Vesa
Enable all the necessary configs for SPL DM and FIT support for mx6sabresd. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15configs: mx6sabreauto: Add SPL FIT and DM supportAbel Vesa
Enable all the necessary configs for SPL DM and FIT support for mx6sabreauto. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15arm: dts: Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd]Abel Vesa
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones from kernel v4.20 (commit 8fe28cb58bcb2). Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] filesAbel Vesa
This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15board: mx6sabreauto: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabreauto - imx6qp-sabreauto - imx6dl-sabreauto Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15board: mx6sabresd: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabresd - imx6qp-sabresd - imx6dl-sabresd Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL buildsAbel Vesa
Since the fsl_esdhc will also be used by SPL, make the preprocessor switches more generic to allow any kind of build. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15configs: imx6sabreauto: Add DM_USB supportAbel Vesa
Add the DM support for USB. For that, DM_REGULATOR is needed. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15configs: imx6sabreauto: Add DM_MMC supportAbel Vesa
Add DM_MMC config to imx6sabreauto defconfig. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15usb: ehci-mx6: Make regulator DM_REGULATOR dependentAbel Vesa
Do the regulator related work only if the build has the DM_REGULATOR. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGEAbel Vesa
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL, makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE. Everything that is not part of the usb storage support in SPL is now build under SPL_USB_HOST_SUPPORT. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15video: bmp: Add support for 24bpp BMP files on 16bpp displaysStefan Roese
This patch adds support to load 24bpp BMP files on 16bpp displays. This will be used by the theadorable board. The "old" bmp command did support this operartion mode and to not break compatibility with the move to DM_VIDEO, we need to add this support to the "new" bmp code. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2019-02-15sunxi: display: Implement fallback to ddc probe when hpd failsPriit Laes
There are HDMI displays where hpd pin is not connected, thus we cannot get it to work unless we specifically set the resolution. Rework the display probing, so hotplug detect failure causes fallback to probing ddc for EDID data. Signed-off-by: Priit Laes <priit.laes@paf.com>
2019-02-15sunxi: display: Move DDC PLL setup to HDMI initPriit Laes
Move PLL initialization code to single place so we won't call it every time we query for EDID data. Signed-off-by: Priit Laes <priit.laes@paf.com>
2019-02-15arm64: zynqmp: Create fdtfile from compatible stringMichal Simek
distro boot expects that fdtfile name is setup for alternative DTB. Create this file based on the first platform compatible string. This should ensure that one rootfs can store multiple DTBs for different boards. Reflect structure which is used in Linux kernel. It means dtbs are strored in xilinx folder. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2019-02-15arm64: zynqmp: Change the spi-rx-bus-width property to x1Venkatesh Yadav Abbarapu
As per the zc1275 design x1 mode is enabled so changing the spi-rx-bus-width property to x1. Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15arm64: zynqmp: Fix i2c boot warningShubhrajyoti Datta
Fix the below warning as the core looks for the compatible string. [ 5.198919] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@19 [ 5.207454] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@19 [ 5.216394] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@30 [ 5.224986] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@30 [ 5.233927] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@35 [ 5.242527] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@35 [ 5.263880] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@36 [ 5.272477] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@36 [ 5.281415] i2c i2c-18: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@51 [ 5.290008] i2c i2c-18: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@75/i2c@3/dev@51 Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15arm64: zynqmp: Remove autodetected devices without descriptionMichal Simek
It will never reach mainline that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15arm64: dts: Fix various entry-method properties to reflect documentationAmit Kucheria
The idle-states binding documentation[1] mentions that the 'entry-method' property is required on 64-bit platforms and must be set to "psci". Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states bindings examples") attempted to fix this earlier but clearly more is needed. Linux docs: Documentation/devicetree/bindings/arm/idle-states.txt (see idle-states node) Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15xilinx: dts: Remove additional empty linesMichal Simek
Trivial fix. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15arm64: zynqmp: Add reset-on-timeout for all boards and modify default ↵Mounika Grace Akula
timeout value This patch adds reset-on-timeout to FPD WDT which will trigger an interrupt to PMU when watchdog expiry happens and PMU takes the necessary action. If this property is not enabled, reason will not be known when watchdog expiry happens. This patch also modifies the default timeout to 60 seconds. Reason is that if u-boot enables WDT, it will set the timeout to 10 seconds and this is not enough to boot till Linux and start the WDT application in Linux. 60 seconds is the maximum safest value to boot till Linux and start the WDT application. Users need to change this timeout value to fit their needs. Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15ARM: dts: zynq: correct and improve the model property of dt filesLuis Araneda
Replace the current value of the model property by a more accurate description of each board (which includes the manufacturer), as some of the boards had the same value ("Xilinx Zynq") Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boardsLuis Araneda
Both boards are made by Avnet, Inc. So add an additional value to the compatible property Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-01 01:17:55 +0000