summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-06-20Merge branch 'net' of https://gitlab.denx.de/u-boot/custodians/u-boot-sh ↵Tom Rini
into next - Convert pcnet and eepro100 ethernet drivers to DM
2020-06-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
2020-06-19Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spi into nextTom Rini
- Convert fsl_espi to driver model (Chuanhua) - Enable am335x baltos to DM_SPI (Jagan) - Drop few powerpc board which doesn't have DM enabled (Jagan)
2020-06-19Merge tag 'efi-2020-07-rc5-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc5 (2) Fix memory reservations: do not use random bytes from the stack.
2020-06-19Merge tag 'u-boot-stm32-20200619' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - fix SD card cart detect on DHCOM and ST boards
2020-06-19Merge https://gitlab.denx.de/u-boot/custodians/u-boot-tegraTom Rini
2020-06-19ARM: dts: stm32: Reinstate card detect behavior on ST boardsPatrick Delaunay
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far unsupported, reinstate the old cd-gpios behavior until this handling is fully implemented. This avoid potential issue for SDCard boot: the card detect fails with floating gpio. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-06-19ARM: dts: stm32: Reinstate card detect behavior on DHSOMMarek Vasut
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far unsupported, reinstate the old cd-gpios behavior until this handling is fully implemented. This permits the DHSOM to boot from SD again, without this patch the card detect fails. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-06-19cmd: bootefi: Honor the address & size cells properties correctlyAtish Patra
fdtdec_get_addr_size reads the uses a fixed value for address & size cell properties which may not be correct always. Use the auto variant of the function which automatically reads #address-cells & #size-cells from parent and uses to read the "reg" property. Signed-off-by: Atish Patra <atish.patra@wdc.com> On 32 bit systems fdt_addr_t may be 4 bytes long but size is defined as u64. Avoid filling the upper 4 bytes of the sizep parameter of fdtdec_get_addr_size_auto_parent() with random bytes from the stack by defining a separate variable fdt_size. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-18t210: Nano: Add NVME supportTom Warren
This allows Nano to use the key M.2 on the CVB to connect and use a M.2 NVMe SSD stick. Works on my Nano B00, WD SN750 NVMe SSD shows up w/'nvme' commands. Will add booting from NVMe via distro cmds in a future patch. Signed-off-by: Tom Warren <twarren@nvidia.com>
2020-06-18Merge tag 'fixes-for-v2020.07-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video - fix stdout in default environment for apalis_imx6, colibri_imx6 and cm_fx6 boards
2020-06-18Merge tag 'video-next' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video into next - migrate remaining imx5/imx6qd boards to DM_VIDEO - use 'vidconsole' stdout in nitrogen6x upgrade script - add option for selection of the vidconsole commands lcdputs and setcurs - allow building ipuv3 driver with disabled CONFIG_PANEL - make backlight and panel drivers optional - remove useless code from ipuv3 driver - extend existing DM_VIDEO work-around for console name to support 'vga' - remove non-DM code in ipuv3
2020-06-18colibri_t20: change maintainerIgor Opaniuk
Take over maintainership for Colibri T20 module. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Lucas Stach <dev@lynxeye.de>
2020-06-18ARM: tegra: Enable PSCI support for Tegra210 and Tegra186Jon Hunter
The PSCI nodes are currently not populated for the Tegra210 and Tegra186 devices. This prevents the PSCI driver from being able to identify the PSCI method used by these devices and causes the probe of the PSCI driver to fail. Since commit 81ea00838c68 ("efi_loader: PSCI reset and shutdown") was added, which moves the PSCI EFI system reset handler into the PSCI driver, this has prevented the EFI system reset from working for Tegra210 and Tegra186. Therefore, populating these nodes is necessary to fix the EFI system reset for Tegra210 and Tegra186. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-06-18firmware: PSCI: Fix PSCI support for OF live treesJon Hunter
When CONFIG_OF_LIVE is enabled, dev_of_offset() cannot be used and if used returns an invalid offset. This causes the call to fdt_stringlist_get() in the psci_probe() to fail to read the 'method' property from the PSCI node for the device and hence prevents PSCI from working. Fix this by using the ofnode_read_string() API instead of the fdt_stringlist_get() because this will handle reading the property both when CONFIG_OF_LIVE is enabled or disabled. Due to the above problem and since commit 81ea00838c68 ("efi_loader: PSCI reset and shutdown") was added, the EFI system reset has been broken for Tegra210 and Tegra196 platforms. This also fixes the EFI system reset for these Tegra platforms. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-06-18Azure/GitLab: Move to latest Docker imageTom Rini
- Add guestfstools, efitools - Latest Ubuntu/bionic snapshot Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-18video: ipuv3: remove non-DM codeAnatolij Gustschin
All ipuv3 users have been converted, drop obsolete code. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-06-18imx: convert mx53loco board to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfig to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Jason Liu <jason.hui.liu@nxp.com> Acked-by: Jason Liu<jason.hui.liu@nxp.com>
2020-06-18imx: convert mx51evk board to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfig to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-06-18imx: convert gwventana board to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfigs to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Tim Harvey <tharvey@gateworks.com>
2020-06-18imx: convert mx6cuboxi board to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfig to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2020-06-18imx: convert cgtqmx6eval board to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfig to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br>
2020-06-18imx: convert dms-ba16 boards to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfigs to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Akshay Bhat <akshaybhat@timesys.com> Cc: Ken Lin <Ken.Lin@advantech.com.tw>
2020-06-18imx: convert pico-imx6 to DM_VIDEOAnatolij Gustschin
Update defconfig to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <festevam@gmail.com>
2020-06-18imx: convert embest boards to DM_VIDEOAnatolij Gustschin
Migration to DM_VIDEO driver is long overdue. Update defconfigs to enable usage of converted ipuv3 driver DM configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Eric Bénard <eric@eukrea.com>
2020-06-18ARM: rmobile: Increase PHY auto-negotiation timeout to 20sMarek Vasut
The ethernet PHY on all known Gen3 boards takes a while to come out of reset, increase the auto-negotiation timeout to prevent it from timing out in case the ethernet is used right after the board was reset. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-06-18net: pcnet: Add Kconfig entriesMarek Vasut
Add Kconfig entries for the pcnet driver and convert MIPS malta to use those. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Add DM supportMarek Vasut
With all the changes in place, add support for DM into the pcnet driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Split common and non-DM functionsMarek Vasut
Pull the common parts of functions out so they can be reused by both DM and non-DM code paths. The recv() function had to be reworked to fit into this scheme and this means it now only receives one packet at a time instead of spinning in an endless loop. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Wrap name and enetaddr into private dataMarek Vasut
Instead of using the non-DM-only name and enetaddr in struct eth_device, add pointers into the private data which can either point to that non-DM name or a DM one later on. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Wrap iobase into private dataMarek Vasut
Instead of using the non-DM-only iobase in struct eth_device, add one into the private data to make DM and non-DM operation possible. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Pass private data through dev->privMarek Vasut
Get rid of the global point to private data, and rather pass it thought dev->priv. Also remove the unnecessary check for lp being non-NULL, since it is always NULL at this point. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Wrap devbusfn into private dataMarek Vasut
Instead of using eth_device priv for this PCI devbusfn, free it so it could be used for driver private data, and wrap devbusfn into those driver private data. Note that using the name dev for the variable is a trick left for later, when DM support is in place, so dm_pci_virt_to_mem() can be used with minimal ifdeffery. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Drop useless forward declarationsMarek Vasut
Remove those as they are not needed anymore. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Move initialize function at the endMarek Vasut
Move the function at the end of the driver, so we could drop various forward declarations later. No functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Move private data allocation to initializeMarek Vasut
The private data allocation does not have to be done every time the NIC is initialized at run time, move the allocation to initialize function, which means it will be done only once when the driver starts. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Replace memset+malloc with callocMarek Vasut
This combination of functions can be replaced with calloc(), make it so. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Simplify private data allocationMarek Vasut
The current code is horribly complex. Both the RX and TX buffer descriptors are 16 bytes in size, the init block is 32 bytes in size, so simplify the code such that the entire private data of the driver are allocated cache aligned and the RX and TX buffer descriptors are part of the private data. This removes multiple malloc calls and cache flushes. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Use PCI_DEVICE() to define PCI device compat listMarek Vasut
Use this macro to fully fill the PCI device ID table. This is mandatory for the DM PCI support, which checks all the fields. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Drop PCNET_HAS_PROMMarek Vasut
All of one PCNET users has this option set, make this default and drop this config option. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: pcnet: Drop typedef struct pcnet_priv_tMarek Vasut
Use struct pcnet_priv all over the place instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-06-18net: eepro100: Add Kconfig entriesMarek Vasut
Add Kconfig entries for the eepro100 driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Add DM supportMarek Vasut
Add support for driver model to the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Split common parts of non-DM functions outMarek Vasut
Split the common code from the non-DM code, so it can be reused by the DM code later. As always, the recv() function had to be split into the actual receiving part and free_pkt part to fit with the DM. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Drop bd_t pointer from read_hw_addr()Marek Vasut
The pointer is unused, so drop it. Rename the function to start with the eepro100_ prefix. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Add RX/TX rings into the private dataMarek Vasut
The RX/TX DMA descriptor rings are per-device-instance private data, so move them into the private data. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Pass device private data into mdiobusMarek Vasut
Instead of doing ethernet device lookup by name every time there is an MDIO access, pass the driver private data via mdiobus priv to the MDIO bus accessors. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Pass device private data aroundMarek Vasut
This patch replaces the various uses of struct eth_device for accessing device private data with struct eepro100_priv, which is compatible both with DM and non-DM operation. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Introduce device private dataMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2020-06-18net: eepro100: Pass PCI BDF into bus_to_phys()/phys_to_bus()Marek Vasut
This is a trick in preparation for adding DM support. By passing in the PCI BDF into the bus_to_phys()/phys_to_bus() macros and calling that dev, we can substitute dev with udevice when DM support lands and do minor adjustment to the macros to support both DM and non-DM operation. No functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
generated by cgit (git 2.34.1) at 2025-02-07 20:04:44 +0000