summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-07-22rockchip: roc-rk3399-pc: Add custom led_setup()Jagan Teki
roc-rk3399-pc has some specific requirements to support LEDS, environment. board detection and etc prior to U-Boot proper. So as of now SPL would be a better stage for these custom board requirements to support unlike TPL. Adding few of these custom requirements like LEDS in TPL would require extra code pulling and also the size of TPL can grow. So, this patch moves the leds code from TPL into SPL Board init led_setup code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (split tpl.c change as separate patch) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rk3399: Add weak led_setup()Jagan Teki
Add weak led_setup() so that board which has an uncommon led setup code that can make use of custom implementation. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rk3288: Add OF board setupJagan Teki
The new rk3288 revision rk3288w has some changes with respect to legacy rk3288 like hclk_vio in cru and usb host0 ohci. Linux clock driver already handle this via rockchip,rk3288w-cru compatible. USB ohci host can enable via dts for rk3288w based boards. So, add fdt board setup code to update cru compatible with rk3288w-cru compatible if the SOC revision is RK3288W. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: Add rk3288 SoC detection helperJagan Teki
Rockchip SoC's has a new revision chip for rk3288 SoCs. RK3288 has a new revision chip called RK3288W which is similar but different hclk_vio clock and fixed OHCI host. Add common Rockchip SoC detection helper to support this rk3288w detection. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22arm64: dts: rockchip: Add Radxa ROCK Pi 4C supportJagan Teki
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled GPIO pin change compared to 4B, 4C. So, add or enable difference nodes/properties in 4C dts by including common dtsi. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22arm64: dts: rockchip: Add ROCKPi 4A/4B supportJagan Teki
Rock PI 4 has 3 variants of hardware platforms called RockPI 4A, 4B, and 4C. - Rock PI 4A has no Wif/BT. - Rock PI 4B has AP6256 Wifi/BT, PoE. - Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable GPIO pin change compared to 4B, 4C So move common nodes, properties into dtsi file and include on respective variant dts files. Use 4B dts into default rock-pi-4 defconfig until we find any solution for dynamic detection of these variants. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: firefly-rk3399: enable CONFIG_USB_DWC3Kever Yang
To fix below build error: drivers/usb/host/built-in.o: In function `xhci_dwc3_remove': drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy' drivers/usb/host/built-in.o: In function `xhci_dwc3_probe': drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy' Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rk3399: Add default env to support compressed kernel ImageKever Yang
Add default kernel_comp_addr_r and kernel_comp_size to support boot from compressed kernel Image, this space is temporarily used during decompress according to README.distro. Reported-by: Tian Yuanhao <tianyuanhao@aliyun.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: sdram: fix dram_init_banksizeAlex Bee
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board if CONFIG_SPL_OPTEE is set. This is troublesome when booting a linux kernel since this size will be injected in FDT of the kernel. gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE) must not be taken into consideration for calculation of second bank size, since this offset is already included in calculation of "top". After applying this patch 992 MB (1024 MB - 32 MB reserved for optee-os) is correctly calculated and has also been verified on 2 GB boards. Signed-off-by: Alex Bee <knaerzche@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22pci: rockchip: Drop legacy PHY driverJagan Teki
Drop the legacy PHY driver and it's associated code since the PHY handling driver now part of Generic PHY framework. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22pci: rockchip: Switch to generic-phyJagan Teki
Now, we have a PCIe PHY driver as part of the Generic PHY framework. Let's use it instead of legacy PHY driver. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22phy: Add Rockchip PCIe PHY driverJagan Teki
Add the Rockchip PCIe PHY driver as part of Generic PHY framework. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Disable RAM_ROCKCHIP_DEBUGJagan Teki
Disable ram rockchip debug driver for roc-rk3399-pc boards since we have verified ram in many instances with respective U-Boot versions. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: ram: fix debug funcfion define when RAM_ROCKCHIP_DEBUG not setKever Yang
The empty function define should not be in the header file, or else the build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG is disabled. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22ram: rk3399: Mark existing prints via RAM_ROCKCHIP_DEBUGJagan Teki
Right now all these debug statements are printing on the console to make sure proper dram initialization happens.   Mark them into RAM_ROCKCHIP_DEBUG would be more meaningful and work like before since the RAM_ROCKCHIP_DEBUG is by default yet. No functionality changes. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22ram: rk3399: Drop debug stride in driverJagan Teki
stride debug is already present in sdram_common.c via RAM_ROCKCHIP_DEBUG. So, drop the redundant debug stride code in rk3399 driver. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock64-rk3328_defconfig: Add SPI Flash supportJohannes Krottmayer
Add U-Boot SPI Flash support for the PINE64 Rock64 board Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22ARM: dts: rk3328-rock64: Add SPI Flash supportJohannes Krottmayer
Add U-Boot SPI Flash support for the PINE64 Rock64 board Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22ARM: dts: rk3328: Add SPI supportJohannes Krottmayer
Add U-Boot SPI support for the RK3328 Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (fix checkpatch error for code ident) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22drivers: spi: rk_spi: Add support for RK3328Johannes Krottmayer
Add support for the RK3328 SPI controller Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22drivers: clk: rockchip: clk_rk3328: Add SPI supportJohannes Krottmayer
Add SPI support for the RK3328 clock driver Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Update ENV offset, sizeJagan Teki
Adjust the ENV offset, size to fit into all images on 16MB flash. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Enable USB GadgetJagan Teki
Enable DWC3 core, gadget for roc-rk3399-pc board. This would help to use fastboot by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable HDMI outputJagan Teki
Enable config options to get HDMI output on RockPI-4 boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable USB GadgetJagan Teki
Enable USB gadget for rock-pi-4 boards. This would help to use fastboot by default. Note: Connect the Host USB cable (Port A or C) to rock-pi-4 Upper USB 3.0 port. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable PCI/NVMEJagan Teki
Enable PCI/NVME for M.2 Slot on RockPI-4 boards. => nvme info Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Cc: Tom Cubie <tom@radxa.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable USB3 HostJagan Teki
Enable USB3.0 Host support for RockPI-4 boards. Note that the Upper USB3.0 port is marked as otg and lower USB3.0 port marked as host, so this below log capture when USB3.0 mass storage plug in at lower USB 3.0 port. Log: Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3c0000: USB EHCI 1.00 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!? 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (5 Gb/s, 0mA) U-Boot XHCI Host Controller 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 224mA) SanDisk Dual Drive 040130e3ee554b7078843f4eb331646 Cc: Tom Cubie <tom@radxa.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rockpro64: Enable USB3.0 HostJagan Teki
Enable USB3.0 Host support for RockPro64 boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: board: add Hardkernel Odroid Go2 boardHeiko Stuebner
Also known as Odroid Go Advance but named Go2 internally by the vendor it seems. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: px30: sync Odroid Go Advance devicetree from LinuxHeiko Stuebner
Get the devicetree from mainline Linux and include it for U-Boot uses. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: px30: sync the main rk3326 dtsi from mainlineHeiko Stuebner
The rk3326 is just a trimmed down px30 from a software perspective, so the mainline rk3326 dtsi also ist just a tiny addition. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22lib: crypto: export and enhance pkcs7_verify_one()AKASHI Takahiro
The function, pkcs7_verify_one(), will be utilized to rework signature verification logic aiming to support intermediate certificates in "chain of trust." To do that, its function interface is expanded, adding an extra argument which is expected to return the last certificate in trusted chain. Then, this last one must further be verified with signature database, db and/or dbx. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-07-22lib: crypto: add pkcs7_digest()AKASHI Takahiro
This function was nullified when the file, pkcs7_verify.c, was imported because it calls further linux-specific interfaces inside, hence that could lead to more files being imported from linux. We need this function in pkcs7_verify_one() and so simply re-implement it here instead of re-using the code. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-07-22lib: crypto: import pkcs7_verify.c from linuxAKASHI Takahiro
The file, pkcs7_verify.c, will now be imported from linux code (crypto/asymmetric_keys/pkcs7_verify.c in 5.7) and modified to fit into U-Boot environment. In particular, pkcs7_verify_one() function will be used in a later patch to rework signature verification logic aiming to support intermediate certificates in "chain of trust." Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-07-22lib: crypto: enable x509_check_for_self_signed()AKASHI Takahiro
When the file, x509_public_key.c, was imported from linux code in commit b4adf627d5b7 ("lib: crypto: add x509 parser"), x509_check_for_self_signed() was commented out for simplicity. Now it need be enabled in order to make pkcs7_verify_one(), which will be imported in a later patch, functional. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-07-22lib: crypto: add public_key_verify_signature()AKASHI Takahiro
This function will be called from x509_check_for_self_signed() and pkcs7_verify_one(), which will be imported from linux in a later patch. While it does exist in linux code and has a similar functionality of rsa_verify(), it calls further linux-specific interfaces inside. That could lead to more files being imported from linux. So simply re-implement it here instead of re-using the code. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-07-22test/py: efi_secboot: fix additional pylint errorsAKASHI Takahiro
This is a fixup by autopep8 after the commit ("test/py: efi_secboot: apply autopep8"). Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22test/py: efi_secboot: remove unused functionAKASHI Takahiro
'tool_is_in_path' function is no longer used anywhere after Heinrich has removed 'sudo' version of fixture setup. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: use logging for block device messagesHeinrich Schuchardt
Use logging instead of printf() for messages occurring when scanning block devices during the initialization of the UEFI sub-system. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: use logging for bootefi commandHeinrich Schuchardt
Log messages of the bootefi command instead of simply printing them to the console. Do not show "## Application terminated" message when the UEFI binary completed successfully. Adjust the python tests testing for '## Application terminated'. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: returning from UEFI FIT imagesHeinrich Schuchardt
Do not reset the board when returning from an UEFI FIT image. For failed UEFI binary we already print the return status in efi_run_image. Remove duplicate output. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: document efi_save_gd(), efi_restore_gd()Heinrich Schuchardt
Provide function descriptions for efi_save_gd() and efi_restore_gd(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: loosen buffer parameter check in efi_file_readStefan Sørensen
When reading a directory, EFI_BUFFER_TOO_SMALL should be returned when the supplied buffer is too small, so a use-case is to call efi_file_read with *buffer_size=0 and buffer=NULL to obtain the needed size before doing the actual read. So move the buffer!=NULL check to after the buffer size has been checked. This fix allows the Redhat shim fallback to run and e.g. Fedora 32 now boots out of the box. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: Check for the native OP-TEE result on mm_communicate callsIlias Apalodimas
Currently we only check for the return value of tee_invoke_func(). Although OP-TEE and StMM will correctly set param[1].u.value.a and we'll eventually return an error, the correct thing to do is check for the OP_TEE return code as well. So let's check for that and move tee_shm_free() and tee_close_session() before exiting with an error to make sure we always clear the registered memory. Fixes: f042e47e8fb43 ("efi_loader: Implement EFI variable handling via OP-TEE") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Use EFI_DEVICE_ERROR for TEE communication problems. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: Rename and correct values for ARM_SMC_MM_*Ilias Apalodimas
Instead of adding the definition for the specific MM SVC used in StandAloneMM we added the one used in the standard SMC calls. So change the value from -4 to -5 to match the correct one defined in EDK2 and rename them to avoid future confusion Fixes 23a397d2e2fb: ("efi_loader: Add headers for EDK2 StandAloneMM communication") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: don't use memmove() in efi_var_mem_del()Heinrich Schuchardt
efi_var_mem_del() is in __efi_runtime because it would be needed for a runtime implementation of SetVariable(). memmove() is not in __efi_runtime. So we should not use it in efi_var_mem_del(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-22efi_loader: efi_current_var after SetVirtualAddressMapHeinrich Schuchardt
Variable efi_current_var is a pointer to a physical memory address that becomes invalid after SetVirtualAddressMap(). Instead of converting it via ConvertPointer() simply set it to NULL. Fixes: b02a707152dc ("efi_loader: enable UEFI variables at runtime") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-21Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spiTom Rini
- add new series Micron SPI NAND devices (Shivamurthy)
2020-07-20treewide: convert devfdt_get_addr() to dev_read_addr()Masahiro Yamada
When you enable CONFIG_OF_LIVE, you will end up with a lot of conversions. To generate this commit, I used coccinelle excluding drivers/core/, include/dm/, and test/ The semantic patch that makes this change is as follows: <smpl> @@ expression dev; @@ -devfdt_get_addr(dev) +dev_read_addr(dev) </smpl> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-20treewide: remove (phys_addr_t) casts from devfdt_get_addr()Masahiro Yamada
This cast is unneeded. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2025-01-08 10:17:06 +0000