summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-04-08Blackfin: bf526-ezbrd: get MAC from flashMike Frysinger
The MAC address is stored in the last flash sector rather than OTP. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf518f-ezbrd: get MAC from flashMike Frysinger
The MAC address is stored in the last flash sector rather than OTP. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf548-ezkit: move env sectorMike Frysinger
U-Boot itself takes up more than 0x40000 bytes, so we can't use that sector for the environment. Move it down a page. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: replace "bfin_reset_or_hang()" with "panic()"Kyle Moffett
The bfin_reset_or_hang function unnecessarily duplicates the panic() logic based on CONFIG_PANIC_HANG. This patch deletes 20 lines of code and just calls panic() instead. This also makes the following generic-restart conversion patch simpler. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: adi boards: enable CONFIG_MONITOR_IS_IN_RAMMike Frysinger
Our monitor is always in RAM, so enable this define for the CFI layer. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bfin_sdh: add support for multiblock operationsSonic Zhang
Don't forget to count full data size for the multiblock operation request. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bfin_sdh: set all timer bits before transferCliff Cai
The timer register is 32bits, not 16bit, so 0xFFFF won't fill it. Write out -1 to make sure to fill the whole thing. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: adi boards: enable ldrinfoMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: ldrinfo: new commandMike Frysinger
Simple command to decode/check an LDR image before we try to boot it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bootldr: use common definesMike Frysinger
Now that the common bootrom.h sets up defines for us, switch to them rather than our own local set. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bootrom.h: sync with toolchainMike Frysinger
We need the updated LDR bit defines for our LDR utils. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: adi boards: drop old ELF defineMike Frysinger
This define isn't used anywhere anymore, so punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf506f-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: default to L1 bank A when L1 bank B does not existMike Frysinger
Some parts lack Bank B in L1 data, so have the linker script fall back to Bank A when that happens. This way we can still leverage L1 data. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: turn off caches when self initializingMike Frysinger
When bootstrapping ourselves on the fly at runtime (via "go"), we need to turn off the caches to avoid taking software exceptions. Since caches need CPLBs and CPLBs need exception handlers, but we're about to rewrite the code in memory where those exception handlers live, we need to turn off caches first. This new code also encourages a slight code optimization by storing the MMR bases in dedicated registers so we don't have to fully load up the pointer regs multiple times. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: only check for os log when we have external memoryMike Frysinger
If the part has no external memory configured, then there will be no os log for us to check, and any attempt to access that memory will trigger hardware errors. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: BF537: unify duplicated headersMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: BF52x: unify duplicated headersMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: drop duplicate system mmr and L1 scratch definesMike Frysinger
Common code already takes care of setting up these defines when a port hasn't specified them, so punt the duplicate values. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: BF50x: new processor portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: fix bd_t handlingMike Frysinger
The recent global data changes (making the size autogenerated) broke the board info handling on Blackfin ports as we were lying and lumping the bd_t size in with the gd_t size. So use the new dedicated bd_t size to setup its own address in memory. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf561-ezkit/ibf-dsp561: invert env offset/addr logicMike Frysinger
Have CONFIG_ENV_ADDR be based on CONFIG_ENV_OFFSET rather than the other way around so that we can use CONFIG_ENV_OFFSET during build. It also avoids a little address duplication. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf537: fix L1 data definesMike Frysinger
The __BFIN_DEF_ADSP_BF537_proc__ define isn't setup anymore, so use the one coming from the compiler. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf537-minotaur/bf537-srv1: undefine nfs when net is disabledMike Frysinger
Fixes a build error due to new partial linking logic. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: serial: clean up muxing a bitMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf525-ucr2: new board portChong Huang
Signed-off-by: Chong Huang <chuang@ucrobotics.com> Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: dnp5370: new board portAndreas Schallenberg
Info about the hardware can be found here: http://www.dilnetpc.com/dnp0086.htm Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf537-pnav/blackstamp/blackvme: drop empty config.mk filesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf527-sdp: update custom CFLAGS pathsMike Frysinger
Looks like the filesystem shuffling missed the SDP board. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: move CONFIG_BFIN_CPU back to board config.hMike Frysinger
This is a revert of 821ad16fa9900c as Wolfgang doesn't like the new code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: unify bootmode based LDR_FLAGS setupMike Frysinger
Unify this convention for all Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: drop CONFIG_SYS_TEXT_BASE from boardsMike Frysinger
We don't want/use this value for Blackfin boards, so punt it and have the common code error out when people try to use it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: skip RAM display for 0 mem systemsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bf518f-ezbrd: don't require SPI logic all the timeMike Frysinger
Only the first run of boards had a ksz switch on it, so if building for a newer silicon rev or SPI is disabled, don't bother checking for the ksz. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-07mtd, cfi: introduce void flash_protect_default(void)Heiko Schocher
collect code which protects default sectors in a function, called flash_protect_default. So boardspecific code can call it too. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-07cfi_flash: use AMD fixups for AMIC (e.g. A29L160A series) tooMario Schuknecht
Signed-off-by: Mario Schuknecht <m.schuknecht@dresearch.de> Signed-off-by: Steffen Sledz <sledz@dresearch.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-05powerpc/85xx: Add some defines & registers in immap_85xx.hZhao Chenhui
* Added SDHCDCR register to GUR struct * Added SDHCDCR_CD_INV define related to SDHCDCR * Added Pin Muxing define related to TDM on P102x Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang
P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05powerpc/85xx: don't init SDRAM when CONFIG_SYS_RAMBOOTZhao Chenhui
Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
Conflicts: drivers/usb/host/ehci-pci.c Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-04-05Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk
2011-04-04powerpc: clean up DIU macro definitions for Freescale reference boardsTimur Tabi
Clean up the macro defintions used to enable DIU (video) support on the MPC8610HPCD and the MPC5121ADS so that they look more like the P1022DS, which is newer. Add software cursor support to all three boards. Also document the CONFIG_FSL_DIU_FB in the README. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Enable eSDHC boot support on P2020 DSJerry Huang
We implement our own mmc_get_env_addr since the environment variables are written to just after the u-boot image on SDCard, so we must read the MBR to get the start address and code length of the u-boot image, then calculate the address of the env. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04env_mmc: Allow board code to override the environment addressMingkai Hu
On some boards the environment may not be located at a fixed address in the MMC/SDHC card. This allows those boards to implement their own means to report what address the environment is located at. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/8xxx: Fix typo for address hashing messageKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04mpc8xxx: DDR2/DDR3: Clean up DIMM-type switch statementsKyle Moffett
The numeric constants in the switch statements are replaced by #defines added to the common ddr_spd.h header. This dramatically improves the readability of the switch statments. In addition, a few of the longer lines were cleaned up, and the DDR2 type for an SO-RDIMM module was added to the DDR2 switch statement. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04fsl_ddr: Don't use full 64-bit divides on 32-bit PowerPCKyle Moffett
The current FreeScale MPC-8xxx DDR SPD interpreter is using full 64-bit integer divide operations to convert between nanoseconds and DDR clock cycles given arbitrary DDR clock frequencies. Since all of the inputs to this are 32-bit (nanoseconds, clock cycles, and DDR frequencies), we can easily restructure the computation to use the "do_div()" function to perform 64-bit/32-bit divide operations. On 64-bit this change is basically a no-op, because do_div is implemented as a literal 64-bit divide operation and the instruction scheduling works out almost the same. On 32-bit PowerPC a fully accurate 64/64 divide (__udivdi3 in libgcc) is over 1.1kB of code and thousands of heavily dependent cycles to compute, all of which is linked from libgcc. Another 1.2kB of code comes in for the function __umoddi3. It should be noted that nothing else in U-Boot or the Linux kernel seems to require a full 64-bit divide on my 32-bit PowerPC. Build-and-boot-tested on the HWW-1U-1A board using DDR2 SPD detection. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Acked-by: York Sun <yorksun@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Fix setting of LIODN prop in PCIe nodes on P3041/P5020Laurentiu TUDOR
We utilize the compatible string to find the node to add fsl,liodn property to. However P3041 & P5020 don't have "fsl,p4080-pcie" compatible for their PCIe controllers as they aren't backwards compatible. Allow the macro's to specify the PCIe compatible to use to allow SoC uniqueness. On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the PCIe controllers. Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/85xx: Add 36-bit address map support to P1022DSJiang Yutang
Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04tsec: add AR8021 PHY supportLi Yang
Signed-off-by: Li Yang <leoli@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-30 03:43:05 +0000