| Age | Commit message (Collapse) | Author |
|---|
|
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
|
|
Replace uint32_t with uintptr_t to remove compilation
warnings for 64-bit architectures.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
|
|
Enable USB IP support for both EHCI and XHCI for
ls1021aqds platform
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Enable USB IP support for both EHCI and XHCI for
ls1021atwr platform
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Add base register address information for USB
XHCI controller on LS1021A
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Add xhci driver support for all FSL socs
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Add support for DWC3 XHCI controller driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
|
|
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Freescale DSPI driver has been converted to Driver Model.
The new driver depends on OF_CONTROL, DM, DM_SPI.
This patch enable FSL_DSPI and its dependence configure options.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Enable DSPI flash related configurations for LS2085ARDB.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Enable DSPI flash related configurations.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS CPLD to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add dts source files for LS2085AQDS and LS2085ARDB boards.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add DSPI controller dts node in fsl-ls2085a.dtsi
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Bring in required device tree files for ls2085a from Linux. These are
initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Linux itb image size has been increased from 30MB.
So updating kernel_size to 40MB in env variable.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Export functions required by Aquntia PHY firmware load application.
functions are memset, strcpy, mdelay, mdio_get_current_dev,
phy_find_by_mask, mdio_phydev_for_ethname and miiphy_set_current_dev
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Change infinite loop mechanism to timer based polling for QBMAN release in
ldpaa_eth_rx.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Polling of TX conf frames is not a mandatory option.
Packets can be transferred via WRIOP without TX conf frame.
Configure ldpaa_eth driver to use TX path without confirmation frame
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Volatile command does not return frame immidiately, need to wait till a frame
is available in DQRR. Ideally it should be a blocking call.
Add timeout handling for DQRR frame instead of retry counter.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Do not immediately return if the enqueue function returns -EBUSY; re-try
mulitple times.
if timeout occures, release the buffer.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
delete any existing ICID pools in the DPC and create
a new one based on the stream ID partitioning for
the SoC
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Management complex major version should match to the firmware present in flash.
Return error during mismatch of major version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update qbman driver
- As per latest available qbman driver
- Use of atomic APIs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Geoff Thorpe <Geoff.Thorpe@freescale.com>
CC: Haiying Wang <Haiying.Wang@freescale.com>
CC: Roy Pledge <Roy.Pledge@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Flush buffer before releasing to BMan after TX_conf to ensure, the core does
not have any cachelines that the WRIOP will DMA to.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Make it easier for the user to notice when the MC firmware
had problems booting.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
|
|
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
|
|
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
