summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-06-19Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: spl/Makefile
2013-06-17MMC: DWMMC: Fix FIFO_DEPTH calculationRajeshwari Shinde
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time for mmc rescan command. In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1). Instead of storing the correct value, we were recalculating the FIFO_DEPT each time which is not correct. Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues" http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247 Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13power: exynos-tmu: use the mux_addr bit fields in tmu_control registerNaveen Krishna Chatradhi
This patch implements the mux_addr bit fields defined in tmu_control register (used for debugging purpose) Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Reviewed-by: Vadim Bendebury <vbendeb@google.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13power: exynos-tmu: fix warnings and clean up codeNaveen Krishna Chatradhi
This patch does the folowing 1. change the data types for unsigned int variable to unsigned 2. change the tmu_base type to struct exynos5_tmu_reg * 3. Add timer functionality for get_cur_temp() 4. error handling in the get_tmu_fdt_values() 5. Add check for curr_temp reading 6. some cosmotic changes. Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Reviewed-by: Vadim Bendebury <vbendeb@google.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partitionAmar
This patch adds commands to access(open/close) and resize boot partitions on EMMC. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13SMDK5250: Enable EMMC bootingAmar
This patch adds support for EMMC booting on SMDK5250. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13MMC: APIs to support resize of EMMC boot partitionAmar
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDTAmar
This patch enables and initialises DWMMC for SMDK5250. Supports both FDT and non-FDT. This patch creates a new file 'exynos5-dt.c' meant for FDT support. exynos5-dt.c: This file shall contain all code which supports FDT. Any addition of FDT support for any module needs to be added in this file. smdk5250.c: This file shall contain the code which supports non-FDT. version. Any addition of non-FDT support for any module needs to be added in this file. May be, the file smdk5250.c can be removed in near future when non-FDT is not required. The Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration. NOTE: Please note that all additions corresponding to FDT need to be added into the file exynos5-dt.c. At same time if non-FDT support is required then add the corresponding updations into smdk5250.c. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted results.Amar
This patch initialises the local variable 'shift' to zero. The uninitialised local variable 'shift' had garbage value and was resulting in unwnated results in the functions exynos5_get_mmc_clk() and exynos4_get_mmc_clk(). Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13EXYNOS5: DWMMC: Added FDT support for DWMMCAmar
This patch adds FDT support for DWMMC, by reading the DWMMC node data from the device tree and initialising DWMMC channels as per data obtained from the node. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13DWMMC: Initialise dwmci and resolve EMMC read write issuesAmar
This patch enumerates dwmci and set auto stop command during dwmci initialisation. EMMC read/write is not happening in current implementation due to improper fifo size computation. Hence modified the fifo size computation to resolve EMMC read write issues. Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13EXYNOS5: FDT: Add DWMMC device node dataAmar
This patch adds DWMMC device node data for exynos5. This patch also adds binding file for DWMMC device node. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13FDT: Add compatible string for DWMMCAmar
Add required compatible information for DWMMC driver. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Amar <amarendra.xt@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13arm:trats: change auto-booting to boot kernel with separate device tree blobArkadiusz Wlodarczyk
Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-12arm: pxa: config option for PXA270 turbo modeSergey Yanovich
PXA270 CPU has turbo mode. The mode is 2.5 times faster than the default run mode. Activating the mode early significantly speeds up boot process. Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
2013-06-12arm: pxa: Add support for ICP DAS LP-8x4xSergey Yanovich
LP-8x4x is a programmable automation controller by ICP DAS. It is shipped with outdated U-Boot v1.3.0 This patch adds enough supports to boot the board: - 128M of 128M SDRAM - 32M of 48M NOR Flash memory - 1 of 4 Serial consoles (PXA FFUART) - 2 of 2 Ethernet controllers (DM9000) Signed-off-by: Sergey Yanovich <ynvich@gmail.com> Series-to: u-boot Series-cc: marex
2013-06-10cosmetic: arm: fix comments in arch/arm/lib/crt0.SMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-06-10Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-06-10arm/km: make local functions staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-06-10arm: da830: moved pinmux configurations to the arch treeVishwanathrao Badarkhe, Manish
Move pinmux configurations for the DA830 SoCs from board file to the arch tree so that it can be used for all da830 based devices. Also, avoids duplicate pinmuxing in case of NAND. Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
2013-06-10ARM: DRA7: Add MaintainerLokesh Vutla
Adding Maintainer for DRA7xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10OMAP5: Enable access to auxclk registersLubomir Popov
auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10ARM: OMAP: I2C: New read, write and probe functionsLubomir Popov
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4 (4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older OMAPs and derivatives as well. The only anticipated exception would be the OMAP2420, which shall require driver modification. - Rewritten i2c_read to operate correctly with all types of chips (old function could not read consistent data from some I2C slaves). - Optimised i2c_write. - New i2c_probe, performs write access vs read. The old probe could hang the system under certain conditions (e.g. unconfigured pads). - The read/write/probe functions try to identify unconfigured bus. - Status functions now read irqstatus_raw as per TRM guidelines (except for OMAP243X and OMAP34XX). - Driver now supports up to I2C5 (OMAP5). Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Heiko Schocher <hs@denx.de>
2013-06-10arm: Remove OMAP2420H4 and all omap24xx supportTom Rini
The omap2420H4 was the only mainline omap24xx board. Prior to being fixed by Jon Hunter in time for v2013.04 it had been functionally broken for a very long time. Remove this board as there's not been interest in it in U-Boot for quite a long time. Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10da830: add MMC supportVishwanathrao Badarkhe, Manish
Add MMC support for da830 boards in order to perform mmc operations(read,write and erase). Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
2013-06-10ARM: OMAP5: Power: Add more functionality to Palmas driverLubomir Popov
Add some useful functions, and the corresponding definitions. Add support for powering on the dra7xx_evm SD/MMC LDO (courtesy Lokesh Vutla <lokeshvutla@ti.com>). Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-06-10ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R
DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: clocks: Update PLL valuesLokesh Vutla
Update PLL values. SYS_CLKSEL value for 20MHz is changed to 2. In other platforms SYS_CLKSEL value 2 represents reserved. But in sys_clk array ind 1 is used for 13Mhz. Since other platforms are not using 13Mhz, reusing index 1 for 20MHz. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10ARM: DRA7xx: Update pinmux dataLokesh Vutla
Updating pinmux data as specified in the latest DM Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com>
2013-06-10mmc: omap_hsmmc: Update pbias programmingBalaji T K
Update pbias programming sequence for OMAP5 ES2.0/DRA7 Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: Correct SRAM END addressSricharan R
NON SECURE SRAM is 512KB in DRA7xx devices. So fixing it here. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: Correct the SYS_CLK to 20MHZSricharan R
The sys_clk on the dra evm board is 20MHZ. Changing the configuration for the same. And also moving V_SCLK, V_OSCK defines to arch/clock.h for OMAP4+ boards. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: Change the Debug UART to UART1Sricharan R
Serial UART is connected to UART1. So add the change for the same. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10ARM: DRA7xx: Do not enable srcomp for DRA7xx Soc'sLokesh Vutla
Slew rate compensation cells are not present for DRA7xx Soc's. So return from function srcomp_enable() if soc is not OMAP54xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: OMAP5: DRA7xx: support class 0 optimized voltagesNishanth Menon
DRA752 now uses AVS Class 0 voltages which are voltages in efuse. This means that we can now use the optimized voltages which are stored as mV values in efuse and program PMIC accordingly. This allows us to go with higher OPP as needed in the system without the need for implementing complex AVS logic. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: clocks: Fixing i2c_init for PMICLokesh Vutla
In DRA7xx Soc's voltage scaling is done using GPI2C. So i2c_init should happen before scaling. I2C driver uses __udelay which needs timer to be initialized. So moving timer_init just before voltage scaling. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: power Add support for tps659038 PMICLokesh Vutla
TPS659038 is the power IC used in DRA7XX boards. Adding support for this and also adding pmic data for DRA7XX boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: DRA7xx: Add control id code for DRA7xxLokesh Vutla
The registers that are used for device identification are changed from OMAP5 to DRA7xx. Using the correct registers for DRA7xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: OMAP4+: pmic: Make generic bus init and write functionsLokesh Vutla
Voltage scaling can be done in two ways: -> Using SR I2C -> Using GP I2C In order to support both, have a function pointer in pmic_data so that we can call as per our requirement. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.hLokesh Vutla
To be consistent with other ARM platforms, renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: OMAP5: clocks: Do not enable sgx clocksSricharan R
SGX clocks should be enabled only for OMAP5 ES1.0. So this can be removed. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10ARM: OMAP4+: Cleanup header filesLokesh Vutla
After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10OMAP5: Fix bug in omap5_es1_prcm structLubomir Popov
The newly introduced function setup_warmreset_time(), called from within prcm_init(), tries to write to the prm_rsttime OMAP5 register. The struct member holding this register's address is however initialized for OMAP5 ES2.0 only. On ES1.0 devices this uninitialized value causes a second (warm) reset at startup. Add .prm_rsttime address init to the ES1.0 struct. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Tom Rini <trini@ti.com>
2013-06-10OMAP5: add ABB setup for MPU voltage domainAndrii Tseglytskyi
Patch adds a call of abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
2013-06-10OMAP3+: introduce generic ABB supportAndrii Tseglytskyi
Adaptive Body Biasing (ABB) modulates transistor bias voltages dynamically in order to optimize switching speed versus leakage. Adaptive Body-Bias ldos are present for some voltage domains starting with OMAP3630. There are three modes of operation: * Bypass - the default, it just follows the vdd voltage * Foward Body-Bias - applies voltage bias to increase transistor performance at the cost of power. Used to operate safely at high OPPs. * Reverse Body-Bias - applies voltage bias to decrease leakage and save power. Used to save power at lower OPPs. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com> Acked-by: Nishanth Menon <nm@ti.com>
2013-06-10am33xx: Board: Make CPSW section of ethernet initialization depend on CPSW ↵Joel A Fernandes
driver Not doing so breaks cases where CPSW is not required such as for USB RNDIS network boot. Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
2013-06-08Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: drivers/serial/Makefile
2013-06-06ARM: tegra: only enable SCU on Tegra20Tom Warren
The non-SPL build of U-Boot on Tegra only runs on a single CPU, and hence there is no need to enable the SCU when running U-Boot. If an SMP OS is booted, and it needs the SCU enabled, it will enable the SCU itself. U-Boot doing so is redundant. The one exception is Tegra20, where an enabled SCU is required for some aspects of PCIe to work correctly. Some Tegra SoCs contain CPUs without a software-controlled SCU. In this case, attempting to turn it on actively causes problems. This is the case for Tegra114. For example, when running Linux, the first (or at least some very early) user-space process will trigger the following kernel message: Unhandled fault: imprecise external abort (0x406) at 0x00000000 This is typically accompanied by that process receving a fatal signal, and exiting. Since this process is usually pid 1, this causes total system boot failure. Signed-off-by: Tom Warren <twarren@nvidia.com> [swarren, fleshed out description, ported to upstream chipid APIs] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-06-06vf610twr: Drop unneeded 'status' variableFabio Estevam
No need to use the 'status' variable, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-06-06ARM: imx: Fix incorrect usage of CONFIG_SYS_MMC_ENV_PARTFabio Estevam
When running the "save" command several times on a mx6qsabresd we see: U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed This issue is caused by the incorrect usage of CONFIG_SYS_MMC_ENV_PART. CONFIG_SYS_MMC_ENV_PART should be used to specify the mmc partition that stores the environment variables. On some imx boards it is been incorrectly used to pass the partition of kernel and dtb files for the 'mmcpart' script variable. Remove the CONFIG_SYS_MMC_ENV_PART usage and configure the 'mmcpart' variable directly. Reported-by: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-26 04:35:18 +0000