summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-11-15ARM64: zynqmp: Support for multiple PM IDs assigned to a PM domainFilip Drazic
Previously, it was assumed that there is a 1:1 mapping between PM ID defined in the platform firmware and a PM domain. However, there can be a situation where multiple PM IDs belong to a single PM domain (e.g. PM IDs for GPU and two pixel processors correspond to a single PM domain). This patch adds support for assigning more than one PM ID to a single PM domain. Updated documentation accordingly. Assigned pixel processors PM IDs to GPU PM domain. Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: DT: Add PM domains for GPU and PCIEFilip Drazic
Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: DT: Remove unused PM domains for PLLFilip Drazic
Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: DT: Remove unused DDR PM domainFilip Drazic
DDR power states are handled by the PM firmware, so this domain is redundant. Also, since there is no device using this PM domain, it will be powered off during boot, which is wrong. Signed-off-by: Filip Drazic <filip.drazic@aggios.com> Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Remove note about level shifter on zcu102Michal Simek
i2c device is just level shifter. Remove reference from dts. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Add dcc port to dtsiMichal Simek
Add dcc to dtsi for supporting system without serial port. DCC is enabled by default on ZynqMP. Adding dcc to zcu100 and zcu102 which were tested. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Add gpio-keys for zcu102Michal Simek
There is gpio push button on MIO22. Add it to DTS to have full board description. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Enable gpio-led as heartbeat on zcu102Michal Simek
Show user that Linux is alive on the board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Enable can1 for ep108Naga Sureshkumar Relli
This patch enables can1 for ep108. Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com> Reviewed-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Added clocks to DT for ep108VNSL Durga
Added clks for ep108 platform. Signed-off-by: VNSL Durga <vnsldurg@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Add clocks for LPDDMAKedareswara rao Appana
Zynqmp DMA driver expects two clocks (main clock and apb clock) LPDDMA clock cofiguration is missing for the same in the zynqmp-clk.dtsi file. This patch updates for the same. Reported-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Remove DTC 1.4.2 warningsMichal Simek
DTC 1.4.2 reports these warnings: Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /amba has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name This patch is fixing them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM: zynq: Remove DTC 1.4.2 warningsMichal Simek
DTC 1.4.2 reports these warnings: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property This patch is fixing them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Correct the sdhci minimum frequency for ep108Siva Durga Prasad Paladugu
Correct the sdhci minimum frequency for ep platform. It should be right shift instead of left shift operand. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Ignore warnings from autogenerated filesMichal Simek
Autogenerated files contain casting issues and missing function declaration and even usleep implementation. Suppress them for now till these files are fixed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Fix secondary bootmode enablingMichal Simek
Do not setup use_alt bit which copy alternative boot mode to boot mode. The reason is that this bit is cleared after POR but not after any software reset which will cause that after SW reset bootrom will look for different boot image. This patch setups alternative boot mode selection (purely SW handling) and extends code to read this alternative boot mode first and use it if it is setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Add support for SD1 with level shifters bootmodeSiva Durga Prasad Paladugu
Add support for SD1 with level shifters bootmode. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Record board name as serial number for DFU/FASTBOOTMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM64: zynqmp: Adjust to new SMC interface to get silicon versionSoren Brinkmann
The new FW interface returns the IDCODE and version register, leaving extracting bitfields to the caller. Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM: zynq: Add support for Zynq 7000S 7007s/7012s/7014s devicesMichal Simek
Zynq 7000S (Single A9 core) devices is using different ID code. This patch adds this new codes and assign them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15net: zynq_gem: Correct SGMII enable bit settingSiva Durga Prasad Paladugu
Correct the SGMII enable bit position to 27 instead of 31. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-15net: zynq_gem: Modify the nwcfg bit definitionsSiva Durga Prasad Paladugu
Modify the nwcfg bit definitions to have 32-bit by removing the extra nibble. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-15nand: arasan_nfc: Clear ecc on bit while sending read commandSiva Durga Prasad Paladugu
Clear ecc ON bit while sending read command as all types of read command(like reading spare) doesnt need ECC to be enabled. It has been anyway taken care in other places whereever required using arasan_nand_enable_ecc(). Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15zynq: nand: Runtime detection of nand buswidth through slcrMichal Simek
This patch adds support to check the buswidth on nand flash at runtime based on nand MIO configurations done by FSBL. User needs to correctly configure the MIO's based on the buswidth supported by the nand flash which is present on the board. Added nand8 and nand16 @periph names on slcr driver. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15zynq: nand: Enable Nand flash controller driver a zynq boardSiva Durga Prasad Paladugu
Enable zynq Nand flash controller driver for a zynq ZC770 XM011(dc2) board. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15mtd: nand: zynq_nand: Add nand driver support for zynqSiva Durga Prasad Paladugu
Add nand flash controller driver support for zynq SoC. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM: zynq: Add support for the topic-miami system-on-modules and carrier boardsMike Looijmans
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM, 32MB QSPI NOR flash and 256MB NAND flash. The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC, 2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources and a fan controller. The "Florida" carrier boards add SD, USB, ethernet and other interfaces. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15ARM: zynq: Make SYS_VENDOR configurableMike Looijmans
Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15tools: mkimage: Check if file is regular fileMichal Simek
Current Makefile.spl passes -R parameter which is not empty and pointing to ./ folder. "./tools/mkimage -T zynqmpimage -R ./"" -d spl/u-boot-spl.bin spl/boot.bin" That's why mkimage is trying to parse ./ file and generate register init which is wrong. Check that passed filename is regular file. If not do not work with it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15tools: mkimage: Add support for initialization table for Zynq and ZynqMPMike Looijmans
The Zynq/ZynqMP boot.bin file contains a region for register initialization data. Filling in proper values in this table can reduce boot time (e.g. about 50ms faster on QSPI boot) and also reduce the size of the SPL binary. The table is a simple text file with register+data on each line. Other lines are simply skipped. The file can be passed to mkimage using the "-R" parameter. It is recommended to add reg init file to board folder. For example: CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-14x86: Enable EFI loader supportSimon Glass
Enable this so that EFI applications (notably grub) can be run under U-Boot on x86 platforms. At present the 'hello world' EFI application is not supported for the qemu-x86_efi_payload64 board. That board builds a payload consisting of a 64-bit header and a 32-bit U-Boot, which is incompatible with the way the EFI loader builds its EFI application. The following error is obtained: x86_64-linux-ld.bfd: i386 architecture of input file `lib/efi_loader/helloworld.o' is incompatible with i386:x86-64 output This could be corrected with additional Makefile rules. For now, this feature is disabled for that board. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [agraf: drop hello kconfig bits] Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: x86: Adjust EFI files support efi_loaderSimon Glass
Add compiler flags and make a few minor adjustments to support the efi loader. Signed-off-by: Simon Glass <sjg@chromium.org> [agraf: Add Kconfig dep] Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14x86: Move efi .S files into the 'lib' directorySimon Glass
These files now need to be in a standard place so that they can be located by generic Makefile rules. Move them to the 'lib' directory. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14x86: Move efi .lds files into the 'lib' directorySimon Glass
These files now need to be in a standard place so that they can be located by generic Makefile rules. Move them to the 'lib' directory. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: arm: Add aarch64 EFI app supportSimon Glass
Add support for EFI apps on aarch64. This includes start-up and relocation code plus a link script. Signed-off-by: Simon Glass <sjg@chromium.org> [agraf: add kconfig dep] Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: arm: Add EFI app supportSimon Glass
Add support for EFI apps on ARM. This includes start-up and relocation code, plus a link script and some compiler setting changes. Signed-off-by: Simon Glass <sjg@chromium.org> [agraf: Remove whitespace change, add kconfig dep] Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14elf: arm: Add a few ARM relocation typesSimon Glass
Rather than hard-coding the relocation type, add it to the ELF header file and use it from there. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: Add support for a hello world test programSimon Glass
It is useful to have a basic sanity check for EFI loader support. Add a 'bootefi hello' command which loads HelloWord.efi and runs it under U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> [agraf: Fix documentation, add unfulfilled kconfig dep] Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: Makefile: Export variables for use with EFISimon Glass
When building an EFI app we need three things: - start-up code - relocation code - link script These are all different for each architecture. We also need special compiler flags in some cases. Add top-level Makefile variables for these along with documentation. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14x86: Tidy up selection of building the EFI stubSimon Glass
At present we use a CONFIG option in efi.h to determine whether we are building the EFI stub or not. This means that the same header cannot be used for EFI_LOADER support. The CONFIG option will be enabled for the whole build, even when not building the stub. Use a different define instead, set up just for the files that make up the stub. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: Fix debug message address formatSimon Glass
This should use U-Boot's standard format for hex address. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: Correct cache flush alignmentSimon Glass
Make sure that the cache flushes correctly by ensuring that the end address is correctly aligned. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14x86: Correct a build warning in x86 tablesSimon Glass
There is a build warning for three x86 boards since write_smbios_table_wrapper() is not used. Fix it. Fixes: e824cf3f (smbios: Allow compilation on 64bit systems) Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi_loader: console: Correctly report modesEmmanuel Vadot
Add support for EFI console modes. Mode 0 is always 80x25 and present by EFI specification. Mode 1 is always 80x50 and not mandatory. Mode 2 and above is freely usable. If the terminal can handle mode 1, we mark it as supported. If the terminal size is greater than mode 0 and different than mode 1, we install it as mode 2. Modes can be switch with cout_set_mode. Changes in V5: Correctly detect mode before enabling mode 2. Changes in V4: Reset cursor positon on mode switch Use local variables in console query code Changes in V3: Valid mode are 0 to EFIMode-1 Fix style Changes in V2: Add mode switch Report only the modes that we support Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi: Use device device path type Messaging for network interface nodeOleksandr Tymoshenko
When adding network interface node use Messaging device path with subtype MAC Address and device's MAC address as a value instead of Media Device path type with subtype File Path and path "Net" Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14efi_loader: fix depends on line of EFI_LOADERMasahiro Yamada
This line is shown as depends on (ARM64 ||\302\240ARM) && OF_LIBFDT on my Emacs. Use ASCII characters only. Assuming it is (ARM64 || ARM), remove the redundancy. Unlike Linux, CONFIG_ARM includes CONFIG_ARM64 in U-Boot. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14Prepare v2016.11Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-14MAINTAINERS: mark sunxi status as OrphanHans de Goede
Ian has not had any time for sunxi for some time now and I'm in the same situation now, so I'm stepping down as sunxi custodian and marking the sunxi support as Orphan. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-11-13video: bmp: Fix compilation errors with CONFIG_BMP_xxBPP enabledStefan Roese
Compiling the 'bmp' command with DM and having one of the following macros enabled: CONFIG_BMP_16BPP, CONFIG_BMP_24BPP ONFIG_BMP_32BPP generates this error: drivers/video/video_bmp.c: In function ‘video_bmp_display’: drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function) fb -= width * 2 + lcd_line_length; ^ This patch moves to using the correct variable instead and enables the 'bmp' command for DM again. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
2016-11-13net: write enetaddr down to hardware on env_callbackMarek Vasut
If mac-address is changed using "setenv ethaddr ...." command the new mac-adress also must be written into the responsible ethernet driver. This fixes the legacy ethernet handling. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
generated by cgit (git 2.34.1) at 2024-12-29 11:09:25 +0000