summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-05-18driver/mtd:IFC: Fix possible memory leakPrabhakar Kushwaha
if priv->bank >= MAX_BANK, priv should be freed before returning ENODEV. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
2012-05-18driver/mtd: IFC NAND: Add support of ONFI NAND flashPrabhakar Kushwaha
- Fix NAND_CMD_READID command for ONFI detect. - Add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
2012-05-18mtd, nand: move some printfs to debug output.Heiko Schocher
current U-Boot shows on startup (for example on the enbw_cmc board) the following printfs from the nand subsystem: Flash: 2 MiB NAND: Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000002980000 nand_read_bbt: Bad block at 0x000003240000 128 MiB MMC: davinci: 0 remove them to debug output, so it shows with this patch: Flash: 2 MiB NAND: 128 MiB MMC: davinci: 0 Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
2012-05-18nand_util: correct YAFFS image write functionLiu, Wentao
In function nand_write_skip_bad(),for YAFFS filesystem part, write_oob() will return 0 when success, so when rval equals 0, it should continue to write the next page, and no break. Signed-off-by: Wentao, Liu <wentao.liu@intel.com> Acked-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
2012-05-18powerpc/85xx: fix NAND boot linker scripts for -fpicScott Wood
GOT is now handled the way the main u-boot.lds does it. Without this, the boot hangs when built with newer GCC (since 4.6). Older toolchains hid the issue by converting -fpic to -fPIC. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-05-18nand: extend .raw accesses to work on multiple pagesScott Wood
A use for this is to read, modify, erase, and write an entire block as a single unit, as a replacement for the biterr command. This way gives more flexibility in that you can also test multiple bit errors, errors in the ECC, etc. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-05-18Improve MAKEALL parallel buildsAndy Fleming
The patch that added parallel builds broke MAKEALL -l, so this fixes that. At the same time, it improves the termination so that it shuts down the build threads if you cancel the build. Lastly, it removes a bunch of debug code. Signed-off-by: Andy Fleming <afleming@freescale.com> Tested-by: Wolfgang Denk <wd@denx.de>
2012-05-18Remove extra boards from LIST_ixpAndy Fleming
pdnb3 and scpu are explicitly on LIST_ixp, even though they are also specified in boards.cfg as having cpu ixp. This means that they will be built twice when doing ./MAKEALL ixp, or ./MAKEALL arm. This was pointless before, but actually breaks things if you launch both builds at the same time, as they overwrite each other. Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-30Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'agust@denx.de' of git://git.denx.de/u-boot-staging: lin_gadget: use common linux/compat.h linux/compat.h: rename from linux/mtd/compat.h lin_gadget: use common mdelay gunzip: rename z{alloc, free} to gz{alloc, free} fs/fat: align disk buffers on cache line to enable DMA and cache part_dos: align disk buffers on cache line to enable DMA and cache
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: powerpc/ppc4xx: Remove typedefs for gdsys FPGA powerpc/ppc4xx: Fix typo in gdsys_fpga.h powerpc/ppc4xx: Update gdsys board configurations powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20 powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes powerpc/ppc4xx: Make gdsys 405ep boards reset more generic powerpc/ppc4xx: Adjust environment size on neo
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-ppc4xx: powerpc/ppc4xx: Remove typedefs for gdsys FPGA powerpc/ppc4xx: Fix typo in gdsys_fpga.h powerpc/ppc4xx: Update gdsys board configurations powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20 powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes powerpc/ppc4xx: Make gdsys 405ep boards reset more generic powerpc/ppc4xx: Adjust environment size on neo
2012-04-30lin_gadget: use common linux/compat.hMike Frysinger
Merge our duplicate definitions with the common header. Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to use min() instead of min_t() since we remove the latter from compat.h. Additionally use memalign() directly as the lin_gadget specific kmalloc() macro is removed from lin_gadget_compat.h by this patch. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
2012-04-30linux/compat.h: rename from linux/mtd/compat.hMike Frysinger
This lets us use it in more places than just mtd code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30lin_gadget: use common mdelayMike Frysinger
No need to provide our own mdelay() macro when we have a func for it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30gunzip: rename z{alloc, free} to gz{alloc, free}Mike Frysinger
This allows us to add a proper zalloc() func (one that does a zeroing alloc), and removes duplicate prototypes. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30fs/fat: align disk buffers on cache line to enable DMA and cacheEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30part_dos: align disk buffers on cache line to enable DMA and cacheEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30Allow for parallel builds and saved outputAndy Fleming
The MAKEALL script cleverly runs make with the appropriate options to use all of the cores on the system, but your average U-Boot build can't make much use of more than a few cores. If you happen to have a many-core server, your builds will leave most of the system idle. In order to make full use of such a system, we need to build multiple targets in parallel, and this requires directing make output into multiple directories. We add a BUILD_NBUILDS variable, which allows users to specify how many builds to run in parallel. When BUILD_NBUILDS is set greater than 1, we redefine BUILD_DIR for each build to be ${BUILD_DIR}/${target}. Also, we make "./build" the default BUILD_DIR when BUILD_NBUILDS is greater than 1. MAKEALL now tracks which builds are still running, and when one finishes, it starts a new build. Once each build finishes, we run "make tidy" on its directory, to reduce the footprint. As a result, we are left with a build directory with all of the built targets still there for use, which means anyone who wanted to use MAKEALL as part of a test harness can now do so. Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot cmd_bdinfo: display the address map size (32-bit vs. 36-bit) PowerPC: correct the SATA for p1/p2 rdb-pc platform powerpc/corenet_ds: Slave core in holdoff when boot from SRIO powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO powerpc/corenet_ds: Slave uploads ucode when boot from SRIO powerpc/corenet_ds: Slave module for boot from SRIO powerpc/corenet_ds: Master module for boot from SRIO powerpc/corenet_ds: Document for the boot from SRIO powerpc/corenet_ds: Correct the compilation errors about ENV powerpc/srio: Rewrite the struct ccsr_rio powerpc/85xx:Fix lds for nand boot debug info powerpc/p2041rdb: add env in NAND support powerpc/p2041rdb: add NAND and NAND boot support powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards powerpc/85xx:Avoid vector table compilation for nand_spl powerpc/85xx:Fix IVORs addr after vector table relocation powerpc/85xx:Avoid hardcoded vector address for IVORs powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot cmd_bdinfo: display the address map size (32-bit vs. 36-bit) PowerPC: correct the SATA for p1/p2 rdb-pc platform powerpc/corenet_ds: Slave core in holdoff when boot from SRIO powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO powerpc/corenet_ds: Slave uploads ucode when boot from SRIO powerpc/corenet_ds: Slave module for boot from SRIO powerpc/corenet_ds: Master module for boot from SRIO powerpc/corenet_ds: Document for the boot from SRIO powerpc/corenet_ds: Correct the compilation errors about ENV powerpc/srio: Rewrite the struct ccsr_rio powerpc/85xx:Fix lds for nand boot debug info powerpc/p2041rdb: add env in NAND support powerpc/p2041rdb: add NAND and NAND boot support powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards powerpc/85xx:Avoid vector table compilation for nand_spl powerpc/85xx:Fix IVORs addr after vector table relocation powerpc/85xx:Avoid hardcoded vector address for IVORs powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: i2c:designware Turn off the ctrl when setting the speed i2c: Add support for designware i2c controller sh: i2c: Add support I2C controller of SH7734
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: i2c:designware Turn off the ctrl when setting the speed i2c: Add support for designware i2c controller sh: i2c: Add support I2C controller of SH7734
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: Blackfin: bfin_sdh: drop dos part hardcode Blackfin: move gd/bd to bss by default Blackfin: gd_t: relocate volatile markings
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: bfin_sdh: drop dos part hardcode Blackfin: move gd/bd to bss by default Blackfin: gd_t: relocate volatile markings
2012-04-30image/fit: drop inline markings on parser codeMike Frysinger
Putting "inline" on extern funcs makes no sense, so drop them. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-nds32Wolfgang Denk
* 'master' of git://git.denx.de/u-boot-nds32: board/adp-ag102: add configuration of adp-ag102 board/adp-ag102: add board specific files nds32/ag102: add ag102 soc support nds32/ag102: add header support of ag102 soc
2012-04-30powerpc/ppc4xx: Remove typedefs for gdsys FPGADirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Fix typo in gdsys_fpga.hDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Update gdsys board configurationsDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20Dirk Eibach
In hardware revision 1.20 one more fan controller is added to dlvision-10g. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changesDirk Eibach
Print fpga info at last_stage_init on gdsys 405ep boards. Use dtt_init() to startup fans. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Make gdsys 405ep boards reset more genericDirk Eibach
In order to add boards that have different hardware for fpga reset, any 405ep gdsys board now provides these functions: void gd405ep_init(void); void gd405ep_set_fpga_reset(unsigned state); void gd405ep_setup_hw(void); int gd405ep_get_fpga_done(unsigned fpga); Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30powerpc/ppc4xx: Adjust environment size on neoDirk Eibach
Environment size on neo has to be 0x20000 for compatibilty reasons. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30patman: Change the location of patman pathVikram Narayanan
Fix the location of patman path in README Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Cc: Simon Glass <sjg@chromium.org>
2012-04-30patman: Fix a typo errorVikram Narayanan
Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-29GCC47: Fix warning in md5.cMarek Vasut
md5.c: In function ‘MD5Final’: md5.c:156:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] md5.c:157:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-29GCC47: Fix warning in cmd_nand.cMarek Vasut
cmd_nand.c: In function ‘arg_off_size’: cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Scott Wood <scottwood@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2012-04-29Merge branch 'marex@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'marex@denx.de' of git://git.denx.de/u-boot-staging: CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE CMD: Fix typo CMD_FSL -> CMD_MFSL in readme HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM CMD: Remove CMD_LOG, it's unused CMD: Fix typo KGBD -> KGDB on debris board CMD: Drop CONFIG_CMD_EMMC, it's not used CMD: Drop CONFIG_CMD_DFL, it's not used CMD: Drop CMD_DCR, it's not used CMD: Drop CMD_CAN, it's not used CMD: Remove CMD_AUTOSCRIPT, it's not used AT91: Drop AT91_SPIMUX command from cmd_all
2012-04-25Prepare v2012.04.01Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-24powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSRTimur Tabi
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but that register does not exist on e500v1. Signed-off-by: Timur Tabi <timur@freescale.com>
2012-04-24powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during bootTimur Tabi
Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes displays which of these is actually built, but it's inconsistent. This is especially problematic since the "default" build for a given 85xx board can be either one, so if you don't see a message, you can't always know which size is being used. Not only that, but each board includes code that displays the message, so there is duplication. The 'bdinfo' command has been updated to display this information, so we don't need to display it at boot time. The board-specific code is deleted. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24cmd_bdinfo: display the address map size (32-bit vs. 36-bit)Timur Tabi
Some Freescale SOCs support 32-bit and 36-bit physical addressing, and U-Boot must be built to enable one or the other. Add this information to the bdinfo command. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24PowerPC: correct the SATA for p1/p2 rdb-pc platformJerry Huang
For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller. Therefore, the SATA driver will use sata_sil, instead sata_sil3114. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Andy Fleming <afleming@gmail.com>
2012-04-24powerpc/corenet_ds: Slave core in holdoff when boot from SRIOLiu Gang
When boot from SRIO, slave's core can be in holdoff after powered on for some specific requirements. Master can release the slave's core at the right time by SRIO interface. Master needs to: 1. Set outbound SRIO windows in order to configure slave's registers for the core's releasing. 2. Check the SRIO port status when release slave core, if no errors, will implement the process of the slave core's releasing. Slave needs to: 1. Set all the cores in holdoff by RCW. 2. Be powered on before master's boot. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Slave reads ENV from master when boot from SRIOLiu Gang
When boot from SRIO, slave's ENV can be stored in master's memory space, then slave can fetch the ENV through SRIO interface. NOTE: Because the slave can not erase, write master's NOR flash by SRIO interface, so it can not modify the ENV parameters stored in master's NOR flash using "saveenv" or other commands. Master needs to: 1. Put the slave's ENV into it's own memory space. 2. Set an inbound SRIO window covered slave's ENV stored in master's memory space. Slave needs to: 1. Set a specific TLB entry in order to fetch ucode and ENV from master. 2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Slave uploads ucode when boot from SRIOLiu Gang
When boot from SRIO, slave's ucode can be stored in master's memory space, then slave can fetch the ucode image through SRIO interface. For the corenet platform, ucode is for Fman. Master needs to: 1. Put the slave's ucode image into it's own memory space. 2. Set an inbound SRIO window covered slave's ucode stored in master's memory space. Slave needs to: 1. Set a specific TLB entry in order to fetch ucode from master. 2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Slave module for boot from SRIOLiu Gang
For the powerpc processors with SRIO interface, boot location can be configured from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash for u-boot image. The image can be fetched from another processor's memory space by SRIO link connected between them. The processor boots from SRIO is slave, the processor boots from normal flash memory space and can help slave to boot from its memory space is master. They are different environments and requirements: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure SRIO switch system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to SRIO1 or SRIO2 by RCW. 3. RCW should configure the SerDes, SRIO interfaces correctly. 4. Slave must be powered on after master's boot. 5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode locally. For the slave module, need to finish these processes: 1. Set the boot location to SRIO1 or SRIO2 by RCW. 2. Set a specific TLB entry for the boot process. 3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot. 4. Slave's u-boot image should be generated specifically by make xxxx_SRIOBOOT_SLAVE_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Master module for boot from SRIOLiu Gang
For the powerpc processors with SRIO interface, boot location can be configured from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash for u-boot image. The image can be fetched from another processor's memory space by SRIO link connected between them. The processor boots from SRIO is slave, the processor boots from normal flash memory space and can help slave to boot from its memory space is master. They are different environments and requirements: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure SRIO switch system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to SRIO1 or SRIO2 by RCW. 3. RCW should configure the SerDes, SRIO interfaces correctly. 4. Slave must be powered on after master's boot. For the master module, need to finish these processes: 1. Initialize the SRIO port and address space. 2. Set inbound SRIO windows covered slave's u-boot image stored in master's NOR flash. 3. Master's u-boot image should be generated specifically by make xxxx_SRIOBOOT_MASTER_config 4. Master must boot first, and then slave can be powered on. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24powerpc/corenet_ds: Document for the boot from SRIOLiu Gang
This document describes the implementation of the boot from SRIO, includes the introduction of envionment, an example based on P4080DS platform, an example of the slave's RCW, and the description about how to use this feature. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24powerpc/corenet_ds: Correct the compilation errors about ENVLiu Gang
When defined CONFIG_ENV_IS_NOWHERE, there will be some compilation errors: ./common/env_nowhere.o: In function `env_relocate_spec': ./common/env_nowhere.c:38: multiple definition of `env_relocate_spec' ./common/env_flash.o: ./common/env_flash.c:326: first defined here ./common/env_nowhere.o: In function `env_get_char_spec': ./common/env_nowhere.c:42: multiple definition of `env_get_char_spec' ./common/env_flash.o:./common/env_flash.c:78: first defined here ./common/env_nowhere.o: In function `env_init': ./common/env_nowhere.c:51: multiple definition of `env_init' ./common/env_flash.o:./common/env_flash.c:237: first defined here make[1]: *** [./common/libcommon.o] Error 1 make[1]: Leaving directory `./common' make: *** [./common/libcommon.o] Error 2 Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-28 03:22:38 +0000