summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-10-30ls102xa: Adjust some macros for SD boot on LS1021A QDS boardAlison Wang
As more features are added for SD boot on LS1021A QDS board, the size of U-Boot is larger. CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS needs to be adjusted to a suitable value. Starting address of the malloc pool used in SPL needs to be adjusted too, or it will occupy the address u-boot loads. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30configs: ls1021atwr: Enable ID EEPROM for SD bootYao Yuan
I2C1 can work on ls102xa rev2.0 SD boot, so add ID EEPROM for SD boot. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30arm: ls1021atwr: optimize the deep sleep latencytang yuantian
It will take more than 1s when wake up from deep sleep. Most of the time is spent on outputing information. This patch reduced the deep sleep latency by: 1. avoid outputing system informaton 2. remove flush cache after DDR restore 3. skip reloading second stage uboot binary when SD boot Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30SECURE_BOOT: Correct reading of ITS bitAneesh Bansal
The ITS bit was being read incorrectly beacause of operator precedence. The same ahs been corrected. Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30drivers/ddr/fsl_ddr: Make SR_IE configurableJoakim Tjernlund
SR_IE(Self-refresh interrupt enable) is needed for Hardware Based Self-Refresh. Make it configurable and let board code handle the rest. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29arm: ls1021a: Add sata support on qds and twr boardtang yuantian
Freescale ARM-based Layerscape LS102xA contain a SATA controller which comply with the serial ATA 3.0 specification and the AHCI 1.3 specification. This patch adds SATA feature on ls1021aqds and ls1021atwr boards. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29arm: ls102xa: Set fdt_high and initrd_high to the value of 0xffffffffAlison Wang
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel fails to access the device tree blob on boot. The reason is that u-boot relocates the device tree blob into high memory when booting the kernel and the kernel is unable to access the blob. To avoid this issue, fdt_high is set to the value of 0xffffffff. The device tree blob will not get relocated and is still in low memory to make it accessible to the kernel. For the same reason, initrd_high is set to the value of 0xffffffff too. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043a: Enable secondary coresHou Zhiqiang
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to make secondary cores excute in spin loop. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add sd boot supportGong Qianyu
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardbYangbo Lu
This patch adds esdhc support for ls1043ardb. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043a: Add Fman supportShaohui Xie
Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add nand boot supportGong Qianyu
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add LS1043ARDB board supportMingkai Hu
LS1043ARDB Specification: ------------------------- Memory subsystem: * 2GByte DDR4 SDRAM (32bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * XFI 10G port * QSGMII with 4x 1G ports * Two RGMII ports PCIe: * PCIe2 (Lanes C) to mini-PCIe slot * PCIe3 (Lanes D) to PCIe slot USB 3.0: two super speed USB 3.0 type A ports UART: supports two UARTs up to 115200 bps for console Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-29armv8/fsl_lsch2: Add fsl_lsch2 SoCMingkai Hu
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with ARMv8 cores and 2rd generation of Chassis. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/fsl_lsch3: Change arch to fsl-layerscapeMingkai Hu
There are two LS series processors are built on ARMv8 Layersacpe architecture currently, LS2085A and LS1043A. They are based on ARMv8 core although use different chassis, so create fsl-layerscape to refactor the common code for the LS series processors which also paves the way for adding LS1043A platform. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net/fm: fix MDIO controller base on FMAN2Shaohui Xie
MDIO controller base on FMAN2 was defined as CONFIG_SYS_FSL_FM2_ADDR plus offset, but CONFIG_SYS_FSL_FM2_ADDR only defined when there are two FMANs, so we should only define MDIO controller base on FMAN2 when there is FMAN2. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net/fm: Add QSGMII PCS initShaohui Xie
QSGMII PCS needed to be programmed same as SGMII PCS, and there are four ports in QSGMII PCS, port 0, 1, 2, 3, all the four ports shared port 0's MDIO controller, so when programming port 0, we continue to program other three ports. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net: Move some header files to include/Shaohui Xie
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM and PPC, move it out of ppc to include/, and change the path in drivers accordingly. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net: fm: bug fix when CONFIG_PHYLIB not definedShaohui Xie
codes related to phylib operations should be wrapped by CONFIG_PHYLIB. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net/fm: Make the return value logic consistent with conventionHou Zhiqiang
In convention, the '0' is a normal return value indicating there isn't an error. While some functions of FMan IM driver treat '0' as an error return value. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net/fm: Add support for 64-bit platformsHou Zhiqiang
The FMan IM driver is developed for 32-bit platfroms and isn't friendly to 64-bit platforms, so do the minimal refactor: 1. Refine the MURAM management and access. 2. Correct the initialization and operations for QDs and BDs. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29net/fm: Fix the endian issue to support both endianness platformsHou Zhiqiang
The Frame Manager(FMan) is a big-endian peripheral, so the registers, internal MURAM and BDs, which are allocated in main memory and used to communication between core and FMan, should be accessed in big-endian. The big-endian platforms can access them directly as the code implemented so far, while for the little-endian platforms it need to swap the byte-order. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv7/ls1021a: move ns_access to common fileMingkai Hu
Config Security Level Register is different between different SoCs, so put the CSL register definition into the arch specific directory. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29common/board_f.c: change the macro name and remove it for PPC platformsGong Qianyu
For most PPC platforms, they will call the first get_clocks() in init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is then defined to call the second get_clocks(), which should be redundant for PPC. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29arm: ls102xa: enable snooping for CAAM transactionshoria.geanta@freescale.com
Enable snooping for CAAM read & write transactions by programming the SCFG snoop configuration register: SCFG_SNPCNFGCR[SECRDSNP] SCFG_SNPCNFGCR[SECWRSNP] Signed-off-by: Horia Geantă <horia.geanta@freescale.com> Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8: ls2085a: Add support of random MAC addressPrabhakar Kushwaha
Add support of setting RANDOM MAC address if env variable not available. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29driver: net: ldpaa_eth: Set MAC address during interface openPrabhakar Kushwaha
Currently ldpaa ethernet driver rely on DPL file to statically configure mac address for the DPNIs. It is not a correct approach. Add support setting MAC address from env variable or Random MAC address. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8: ls2085ardb: enable CONFIG_PHY_AQUANTIAShaohui Xie
To support on board Aquantia's PHY AQR405. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29crypto/fsl: SEC driver cleanup for 64 bit and endiannessAneesh Bansal
The SEC driver code has been cleaned up to work for 64 bit physical addresses and systems where endianess of SEC block is different from the Core. Changes: 1. Descriptor created on Core is modified as per SEC block endianness before the job is submitted. 2. The read/write of physical addresses to Job Rings will be depend on endianness of SEC block as 32 bit low and high part of the 64 bit address will vary. 3. The 32 bit low and high part of the 64 bit address in descriptor will vary depending on endianness of SEC. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29Data types defined for 64 bit physical addressAneesh Bansal
Data types and I/O functions have been defined for 64 bit physical addresses in arm. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29Pointers in ESBC header made 32 bitAneesh Bansal
For the Chain of Trust, the esbc_validate command supports 32 bit fields for location of the image. In the header structure definition, these were declared as pointers which made them 64 bit on a 64 bit core. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29ls102xa: fdt: Disable IFC in SD boot for QSPIAlison Wang
As QSPI/DSPI and IFC are pin multiplexed, IFC is disabled in SD boot for QSPI. This patch will add fdt support for this rule. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26arm: ls1021a: Add QSPI or IFC support in SD bootAlison Wang
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in SD boot now. For the customer's demand, QSPI needs to be supported in SD boot too. This patch adds QSPI or IFC support in SD boot according to the corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is used to support QSPI in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26QE: modify the address of qe ucodeZhao Qiang
The address of uboot changed, so change qe ucode Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26armv8/fsl-lsch3: fdt: Check the pointer returned from call to a function may ↵Alison Wang
be NULL Pointer 'reg' returned from call to function 'fdt_getprop' may be NULL, will be passed to function and may be dereferenced there by passing argument 1 to function 'of_read_number'. So check pointer 'reg' first. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26fdt_support: Don't panic if stdout alias is missingScott Wood
Currently, using fdt_fixup_stdout() on a device tree that is missing the relevant alias results in this: WARNING: could not set linux,stdout-path FDT_ERR_NOTFOUND. ERROR: /chosen node create failed - must RESET the board to recover. FDT creation failed! hanging...### ERROR ### Please RESET the board ### There is no reason for this to be a fatal error rather than a warning, and removing this allows for a smooth transition on a platform where the device tree currently lacks the correct aliases but will have them in the future. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26arm/fsl-ls: Add CONFIG_OF_STDOUT_VIA_ALIASScott Wood
This will allow OF-based earlycon to be used once the appropriate aliases are added to the device tree and kernel support is fixed. Signed-off-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-24common/board_f.c: modify the macro to use get_clocks() more commonGong Qianyu
get_clocks() should not be limited by ESDHC. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-24arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-24Revert "ARM: zynq: disable CONFIG_SYS_MALLOC_F to fix MMC boot"Simon Glass
This reverts commit 321f86e18d6aae9f7b7ba3ef1eb0cec769481874. The original bug has been fixed. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-on: Zedboard and ZC706 board Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-on: zc702 Tested-by: Michal Simek <michal.simek@xilinx.com>
2015-10-24zynq: Move SPL console init out of board_init_f()Simon Glass
We should not init the console this early since it precludes using driver model for the UART, since it is not set up at the start of board_init_f(). See the README for more information. The debug UART does not have this restriction. If we want to do early init with the console on it can be done in spl_board_init(). Move the preloader_console_init() call from board_init_f() to board_init_r(). Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Michal Simek <michal.simek@xilinx.com>
2015-10-24microblaze: Add a TODO to call board_init_f_mem()Simon Glass
This C function should be used to do the early memory layout and init. This is beyond my powers, so just add a TODO for the maintainer. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Michal Simek <michal.simek@xilinx.com>
2015-10-24arm: Switch 32-bit ARM to using generic global_data setupSimon Glass
There is quite a bit of assembler code that can be removed if we use the generic global_data setup. Less arch-specific code makes it easier to add new features and maintain the start-up code. Drop the unneeded code and adjust the hooks in board_f.c to cope. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-24arm: Switch aarch64 to using generic global_data setupSimon Glass
There is quite a bit of assembler code that can be removed if we use the generic global_data setup. Less arch-specific code makes it easier to add new features and maintain the start-up code. Drop the unneeded code and adjust the hooks in board_f.c to cope. Tested on LS2085ARDB and LS2085AQDS (armv8 SoC). Tested-by: York Sun <yorksun@freescale.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-24board_init_f_mem(): Don't create an unused early malloc() areaSimon Glass
Change the #ifdef so that the early malloc() area is not set up in SPL if CONFIG_SYS_SPL_MALLOC_START is defined. In that case it would never actually be used, and just chews up stack space. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-24board_init_f_mem(): Don't require memset()Simon Glass
Unfortunately memset() is not always available, so provide a substitute when needed. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-24Move board_init_f_mem() into a common locationSimon Glass
This function will be used by both SPL and U-Boot proper. So move it into a common place. Also change the #ifdef so that the early malloc() area is not set up in SPL if CONFIG_SYS_SPL_MALLOC_START is defined. In that case it would never actually be used, and just chews up stack space. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-24fs-test.sh: fix pre-requisite detectionStephen Warren
In the following snippet: if [ ! -x `which $prereq` ]; then When $prereq does not exist, `which $prereq` evaluates to the empty string, which results in *no* argument being passed to the -x operator, which then evaluates to true, which is the equivalent of the prereq having been found. In order for this to fail as expected, we must pass an empty argument, which then causes -x to fail. Do this by wrapping the `` in quotes so there's always an argument to -x, even if the value of the argument is zero-length. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2015-10-24test: fat: add test of non-contiguous file readsStephen Warren
In my patch series to replace fs/fat with "ff.c", I enhanced ff.c to optimize file reading, so that reads of contiguous clusters are submitted to the IO device as a single read. This test attempts to torture-test edge-cases of that enhancement. BTW, the only way I found to validate that this script actually does create non-contiguous files was to manually inspect the FAT bitmap in a hex dump of the FAT image. hdparm --fibmap doesn't work on loop-mounted filesystems. filefrag -v -e seems to lie about files being contiguous when they aren't. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2015-10-24itest: make memory access work under sandboxStephen Warren
itest accesses memory, and hence must map/unmap it. Without doing so, it accesses invalid addresses and crashes. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-27 10:42:23 +0000