summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-11-23rockchip: px30: enable spl-fifo-mode for both emmc and sdmmc on evbHeiko Stuebner
As part of loading trustedfirmware, the SPL is required to place portions of code into the socs sram but the mmc controllers can only do dma transfers into the regular memory, not sram. The results of this are not directly visible in u-boot itself, but manifest as security-relate cpu aborts during boot of for example Linux. There were a number of attempts to solve this elegantly but so far discussion is still ongoing, so to make the board at least boot correctly put both mmc controllers into fifo-mode, which also circumvents the issue for now. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-11-23rockchip: dwmmc: add handling for u-boot, spl-fifo-modeHeiko Stuebner
Rockchips dwmmc controllers can't do dma to non-ddr addresses, like for example the soc-internal sram but during boot parts of TrustedFirmware need to be placed there from the read FIT image. So add handling for a u-boot,spl-fifo-mode to not put the mmc controllers into fifo mode for all time. The regular fifo-mode property still takes precedent and only if not set do we check for the spl-specific property. Suggested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-11-23rock960: Enable USB GadgetJagan Teki
Enable DWC3 core, gadget for rock960 board. This would help to use fastboot by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23rockchip: Setup dwc3_device (for non-dm gadgets)Jagan Teki
Setup dwc3_device structure for non-dm gadgets, which is used in rk3399 platforms. dwc3_device would have basic regbase, dr_mode, high speed and 16-bit UTMI+ etc. Cc: Marek Vasut <marex@denx.de> Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (Fix to use CONFIG_USB_DWC3_GADGET instead of CONFIG_USB_DWC3) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: rockchip: Add rk3399 USB_GADGET_PRODUCT_NUMJagan Teki
Add 0x330c for rk3399 gadget product number. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23usb: dwc3: Add phy interface for dwc3_ubootJagan Teki
U-Boot has two different variants of dwc3 initializations, - with dm variant gadget, so the respective dm driver would call the dwc3_init in core. - with non-dm variant gadget, so the usage board file would call dwc3_uboot_init in core. The driver probe would handle all respective gadget properties including phy interface via phy_type property and then trigger dwc3_init for dm-variant gadgets. So, to support the phy interface for non-dm variant gadgets, the better option is dwc3_uboot_init since there is no dedicated controller for non-dm variant gadgets. This patch support for adding phy interface like 8/16-bit UTMI+ code for dwc3_uboot. This change used Linux phy.h enum list, to make proper code compatibility. Cc: Marek Vasut <marex@denx.de> Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23fastboot: rockchip: Fix rk3328 default mmc deviceJagan Teki
Technically the default mmc device for fastboot would use eMMC if the board support for it. Rockchip platform access device 0 for eMMC so, use the same device number for rk3328. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23fastboot: rockchip: Select FASTBOOT_FLASH[_MMC_DEV]Jagan Teki
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV for rockchip SoC plaforms in fastboot Kconfig file instead of defined it in board defconfig. This eventually drop the explicit configs defined in supporting board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: rockchip: Add rk3128 USB_GADGET_PRODUCT_NUMJagan Teki
Add 0x310c for rk3128 gadget product number. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: rockchip: USB_GADGET_PRODUCT_NUMJagan Teki
Rockchip support differnet or common gadget product number between Rockchip SoCs like, 0x310a - rk3036 0x320a - rk3229, rk3288 0x330a - rk3328 So, select them on Kconfig based on platform specific config defined.     This eventually drop the explicit configs defined in supporting board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: Select USB_GADGET_VENDOR_NUM for rockchipJagan Teki
Gadget vendor number, 0x2207 is common across all platfroms supported in Rockchip SoC. So, select the same number globally, if ARCH_ROCKCHIP. This eventually drop the explicit configs defined in supported board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: Select USB_GADGET_MANUFACTURER for rockchipJagan Teki
Select the gadget manufacturer as 'Rockchip' for all rockchip platform SoC's. This eventually drop the explicit defined added on supported board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23power: fan53555: fix fan53555_regulator_set_valueVasily Khoruzhick
fan53555_regulator_set_value() passes its own dev to pmic_clrsetbits() instead of its parent (pmic). As result u-boot crashes when you try to set voltage on fan53555 regulator Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23rockchip: i2c: don't sent stop bit after each messageVasily Khoruzhick
That's not correct and it breaks SMBUS-style reads and and writes for some chips (e.g. SYR82X/SYR83X). Stop bit should be sent only after the last message. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23power: fan53555: add support for Silergy SYR82X and SYR83XVasily Khoruzhick
SYR82X and SYR83X are almost identical to FAN53555, the only difference is different die ID and revision, voltage ranges and steps. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Tested-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23Kconfig: Enable building of u-boot.itb on Rockchip platformKever Yang
For all the Rockchip SoCs with SPL_LOAD_FIT enable, we need to build u-boot.itb with U-Boot proper and ATF/OPTEE. All the Rockchip boards with SPL_LOAD_FIT now supports FIT generator to get ATF/OPTEE binary path from environment and pass the build even if no ATF/OPTEE binary exist, so we can enable this feature for the rockchip platform. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23rockchip: lion-rk3368: Migrate to use common FIT generatorKever Yang
The RK3368 lion board ATF can use bl31.elf like RK3399 and get the FIT source with generic FIT generator script at: arch/arm/mach-rockchip/make_fit_atf.py And then we can use 'BL31' environment to get the path of bl31.elf instead of copy it into U-Boot folder. CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23rockchip: Convert to use FIT generator for opteeKever Yang
Use generator script so that we can use environment for TEE source. $TEE for tee.bin, and if file not exist, the script can report a warning, and meke the build success without a error. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-18Prepare v2020.01-rc3Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-18Merge tag 'video-for-v2020.01-rc2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video - fix i.MX6ULL evk black screen observed while reboot stress tests - remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree differences between Linux and U-Boot for stm32mp1 platform
2019-11-17Merge tag 'u-boot-rockchip-20191118' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Add support for rockchip SoC: PX30, RK3308 - Add and migrate to use common dram driver: PX30, RK3328, RK3399 - Add rk3399 board Tinker-s support - Board config update for Rock960, Rockpro64
2019-11-17Merge tag 'dm-pull-14nov19' of git://git.denx.de/u-boot-dmTom Rini
Add OP-TEE test swuit Fix patman cc_file output Minor sandbox/pinctrl changes
2019-11-17rockchip: dts: tinker: Add tinker-s board supportMichael Trimarchi
Support tinker-s board. The board is equivalent of tinker board except of emmc. TODO: - support of usb current burst when the board is powered from pc Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: dts: tinker: Move u-boot dmc initialization to specific sectionMichael Trimarchi
dmc is used to initialize the memory controller. It's needed by u-boot. Move it in the specific section Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: imply instead of selecting SPL_SYS_MALLOC_SIMPLEThomas Hebb
We shouldn't force which allocator the SPL uses, since there's no platform requirement for one over the other: in fact, we currently allow selection of the TPL allocator but not the SPL one! Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: allow DRAM init in SPLThomas Hebb
The common SPL removed SoC-specific code for RK3399's SPL and in the process caused the previously-unconditional DRAM initialization in board_init_f() to only happen when compiling a configuration that does not support TPL, meaning DRAM never gets initialized if TPL is supported but disabled. Fix this by omitting the DRAM init in SPL only when we are configured to also build a TPL. This fixes custom configurations that have disabled TPL, and it should also unbreak the "ficus-rk3399", "rock960-rk3399", and "chromebook_bob" defconfigs, although since I don't have any of those devices I can't confirm they're broken now. Fixes: b7abef2ecbcc ("rockchip: rk3399: Migrate to use common spl board file") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: SPL: fix ordering of DRAM initThomas Hebb
The common SPL code reordered the DRAM initialization before rockchip_stimer_init(), which as far as I can tell causes the RK3399 to lock up completely. Fix this issue in the common code by putting the DRAM init back after timer init. I have only tested this on the RK3399, but it wouldn't make any sense for the timer init to require DRAM be set up on any system. Fixes: b7abef2ecbcc ("rockchip: rk3399: Migrate to use common spl board file") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17doc: rockchip: Add documentation for rk3308 based boardsAndy Yan
Add build documentation for rk3308 based boards. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3308: Add support for ROC-RK3308-CC boardAndy Yan
ROC-RK3308-CC is a rk3308 based board designed by Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi on board. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3308: Add dts for ROC-RK3308-CCAndy Yan
Add dts file for ROC-RK3308-CC from firefly. Sync form linux rockchip for v5.5-armsoc/dts64: "arm64: dts: rockchip: Add devicetree for board roc-rk3308-cc" (sha1: 4403e1237be3af0977aa23ef399e3496316317a0) Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: mkimage: add support for RK3308Andy Yan
Usage: (1) tools/mkimage -n rk3308 -T rksd -d tpl/u-boot-tpl.bin idbloader.img (2) cat spl/u-boot-spl.bin >> idbloader.img (3) upgrade_tool wl 0x40 idbloader.img Note: When use ddr binary from rkbin as tpl, use it replace u-boot-tpl.bin in(1) Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3308: Add sdram driverAndy Yan
A dm based dram driver for rk3308 u-boot to get capacity. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17board: rockchip: Add rk3308 evb supportAndy Yan
Add support for rk3308 evaluation board. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17arm: dts: rockchip: Add dts for rk3308 evbAndy Yan
Add dts for rk3308 evb, sync from the linux kernel upstream list [0]. [0]https://patchwork.kernel.org/patch/11201555/ Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: clk: Add clk driver for rk3308Finley Xiao
Add clk controller driver for RK3308 SOC. This patch depends on Elaine's pll patch[0]. [0]http://patchwork.ozlabs.org/patch/1183718/ Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17arm: rockchip: Add RK3308 SOC supportAndy Yan
RK3308 is a quad Cortex A35 based SOC with rich audio interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which designed for intelligent voice interaction and audio input/output processing. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: clk: pll: add common pll setting funcsElaine Zhang
Common PLL setup function, compatible with different SOC. Mainly for the subsequent new SOC use. Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3399: orangepi: Add init value for vdd_logKever Yang
We should set the init value when vdd_log is enabled, or else the vdd_log output voltage may not in soc required range. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3399: khadas-edge: Add init value for vdd_logKever Yang
We should set the init value when vdd_log is enabled, or else the vdd_log output voltage may not in soc required range. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3399: rock-pi4: Add init value for vdd_logKever Yang
We should set the init value when vdd_log is enabled, or else the vdd_log output voltage may not in soc required range. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17arm64: dts: rk3399-rock960: add vdd_log and its init valueKever Yang
Add vdd_log node according to rock960 schematic V13. This patch affect two boards: - Rock960 Model A - Ficus Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-11-17rockchip: dts: rk3399-firefly: move u-boot, spl-boot-order to to the u-boot.dtsiPeter Robinson
The u-boot specific device tree directives should be in u-boot.dtsi Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: dts: rk3399-evb: move u-boot, spl-boot-order to to the u-boot.dtsiPeter Robinson
The u-boot specific device tree directives should be in u-boot.dtsi Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: dts: rk3399: move the u-boot, dm-pre-reloc to the u-boot.dtsiPeter Robinson
The u-boot specific pieces in the dts files should be in u-boot.dtsi not the main files, this allows easier sync with upstream. The rk3399.dtsi has a mix of both so move them all for consistency. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (Fix with missing pmugrf) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3399: split rockpro64 out of evb_rk3399Vasily Khoruzhick
rockpro64 needs to setup I/O domains in order for USB to work in u-boot. Since we currently don't have a driver to do that, split it into its own board file and initialize I/O domains here. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: clk: fix wrong CONFIG_IS_ENABLED handlingHeiko Stuebner
CONFIG_IS_ENABLED() needs the config name like used in Kconfig, so without the leading CONFIG_. The clock drivers all wrongly check for CONFIG_RESET_ROCKCHIP, fix that Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: clk: rv1108: remove duplicate reset initHeiko Stuebner
rockchip_reset_bind() already does the needed init for the reset registers, only referenced the wrong cru structure. So we can get rid of the open-coded reset init and just fix the correct cru reference. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17arm: dts: rk3399-rockpro64: slightly increase center voltageSoeren Moch
The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage scaling. So the regulator reset voltage of 0.9V is used on this board. Let u-boot initialize the center voltage to 0.95V as it is done for the VD_LOGIC domain. This avoids instability and occasional linux kernel Opses on this board. Signed-off-by: Soeren Moch <smoch@web.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17arm: dts: rk3399-rockpro64: sync dts from linux kernelSoeren Moch
The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain. Signed-off-by: Soeren Moch <smoch@web.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17rockchip: rk3399: rock960: Update config for TPLPeter Robinson
Enable TPL for rock960 like other rk3399 boards. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2025-01-12 14:50:44 +0000