| Age | Commit message (Collapse) | Author |
|---|
|
Most of the arndale features are common with other exynos5250 boards. To
permit easier addition of driver model support, use the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
These boards do not in fact have a Chrome OS EC, nor a TPS565090 PMIC, so
move the settings into a separate common file to be used by those that need
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
A few things are common but are not in the common file. Fix this and
rename the file to fit with the other exynos*-common files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Since exynos4 and exyno5 share many settings, we should move these into
a common file to avoid duplication.
In effect the changes are that all exynos boards now have EXT4 and FAT
write support. This affects exynos5250 and exynos5420 which previously
did not. This also disables the ext2 commands which are equivalent to
ext4 anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
We want exynos5250-dt.h to be a board which can support any exynos5250
device. This matches the naming used by Linux. As a first step, rename
the existing -dt files to -common to make it clear they are common files,
and not specific boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Add a keyboard definition so that the keyboard can be used on pit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
With the driver model conversion we are going to be using driver model for
SPI and not for I2C. This works OK so long as a board doesn't need both
dm and non-dm versions of the cros_ec driver. Since pit uses SPI and snow
uses I2C we need to split the configs so that only one driver is compiled
for each platform.
We can fix this later when driver model supports I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards
cannot due to a hardware design decision. Select the correct driver to use
in each case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Unfortunately on Pit the AP has no direct access to the tps65090 but must
talk through the EC (over SPI) to the EC's I2C bus.
When driver model supports PMICs this will be relatively easy. In the
meantime the best approach is to duplicate the driver. It will be refactored
once driver model support is expanded.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Things run faster when the data cache is enabled, so turn it on along with
the 'dcache' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The device seems to hang in SPL if the full speed is used when booting from
USB, perhaps because the PMIC has not been set to the maximum ARM core
voltage yet. Slow it down to a reliable speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
|
|
|
|
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
Fix a trivial conflict in dw_mmc.c after talking with Marek.
Conflicts:
drivers/mmc/dw_mmc.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.
Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
This bit allows the MUSB controller to negotiate for high-speed mode when
the device is reset by the hub. If unset, Babble errors occur with
high-speed mass storage devices right after the first packet. This condition
is not caught by the interrupt handles in U-Boot, so no recovery is done,
and the USB communication is stuck.
To fix this, set the bit unconditionally, not only for
CONFIG_USB_GADGET_DUALSPEED but also for host-only modes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
|
|
Support reading/writing ext4 partitions.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Enable 'fastboot' command.
This is currently enabled but not yet functional. Including it in the
configuration will ease further testing and development as discussed
on the mailing list.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Enable the 'gpio' command to allow reading and toggling of GPIO
pins.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Some users (QNX and Windows CE users in particular) have asked
to disable the Penguin shown on the display at boot time.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Increase the maximum number of arguments allowed by the Hush parser.
This prevents errors when users or scripts aren't quoting parameters
when setting the "bootargs" variable et al.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Enable the "i2c edid" command to query data from an attached
HDMI monitor.
Usage is typically this:
U-Boot > i2c dev 1
U-Boot > i2c edid 0x50
...
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Enable the 'mtest' command on Nitrogen6x and SABRE Lite boards.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Enable the use of USB keyboards on SABRE Lite and Nitrogen6x boards.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
If no boot script was found, expose internal storage over the
USB mass storage gadget to allow easy programming.
This is especially useful when SD cards are inaccessible or when
loading SATA drives.
More details are available in this blog post:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Support RAM disks by setting initrd_high. See commit 7e9603e
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Remove the individual attempts to load using ext2 and fat, replace with the
generic load command supporting available filesystem types.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
|
|
This patch enables boot to USB storage devices by expanding on the list
of boot devices.
Because the USB startup currently takes a long time, it places USB at
the end of the list of supported devices.
You can over-ride the boot order using the bootdevs environment variable.
For instance, this will make USB the first (highest priority) device:
U-Boot > setenv bootdevs usb mmc sata
U-Boot > saveenv
Signed-off-by: Diego Rondini <diego.rondini@kynetics.it>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for the USB mass storage to enable access to on-board
storage (especially eMMC and SATA).
Details at:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
The HPD pin and RX_SENSE registers have proven to be less reliable
than using I2C on the EDID pins for detection of an HDMI monitor.
In particular, when the HDMI output is reset through a "reboot"
cycle, the detect_hdmi() routine often bounces, resulting in
a failure to detect a connected monitor.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for WVGA (800x480) panels using VESA GTF timings over
LVDS.
No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:
U-Boot > setenv panel svga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for an Ampire 1024x600 LVDS panel with integrated Ilitek
capacitive touch screen.
Auto-detection is enabled, so no explicit configuration is needed.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for 800x600 18-bit RGB displays using VESA GTF timings.
No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:
U-Boot > setenv panel svga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for the Touch Revolution Fusion7 display: 800x480 RGB
with a custom F0710A resistive touch controller.
Auto-detection of this panel is supported so no configuration is
required.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
This patch adds support for LVDS WXGA displays that use the SPWG encoding
standard instead of JEIDA.
No auto-detection is enabled and you must explicitly set the 'panel'
environment variable:
U-Boot > setenv panel LDB-WXGA-S
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for LG 9.7" LVDS panel (1024x768) with integrated eGalax
touch screen.
Note that this panel differs only slightly from the Hannstar XGA panel
(margins).
No auto-detection is available because it shares the same touch controller
as the Hannstar-XGA display, so you'll need to configure it through the
'panel' environment variable:
U-Boot > setenv panel LG-9.7
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for a 1/4 VGA panel with a 24-bit RGB interface.
No auto-detection is enabled, so you must configure the 'panel'
environment variable to use this display:
U-Boot > setenv panel qvga
U-Boot > saveenv && reset
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Add support for Boundary Devices 7" and 10.1" 1280x800 displays with
integrated FocalTech ft5x06 10-point touch controller.
Because they share the touch controller with the 1024x600 displays,
auto-detection is disabled and you must explicitly set the 'panel'
environment variable:
U-Boot > setenv panel LDB-WXGA
U-Boot > saveenv && reset
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Include declarations of board_ehci callbacks to prevent compiler warnings
and enforce function prototypes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Testing shows that the Micrel PHY may not be completely out
of reset if accessed immediately.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Declare locally-used data structures and functions as
static and pull in header files to prevent compiler warnings
of "Should it be static?" when building with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Configure CLKO outputs for SGTL5000, CSI camera.
The sys_mclk output for the SGTL500 in particular prevents
Windows CE from properly driving audio.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Ensure that cameras and USB OTG power are in a stable (reset)
state at reset by configuring their pads and toggling GPIOs.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Pads SD2_CLK/CMD/DAT0-3 are connected to an SDIO WiFi device on
Nitrogen and unconnected on BD-SL-i.MX6 (sabre lite).
Configure them as SDIO pins to prevent them from being in a state
that confuses the WiFi part.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
The same logic applies to both SD card slots, only with different
GPIOs and the code should make that easier to see.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
