summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-11-03pmic: bd71837: drop DEBUG macroPeng Fan
Drop DEBUG macro definition which is used for debug purpose. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03dt-bindings: import usb pdPeng Fan
Import usb pd bindings from Linux 5.4.0-rc1. This file will be included by imx8mm-evk.dts. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx: spl: implement spl_boot_mode for i.MX7/8/8MPeng Fan
It will be easy to separate SD/EMMC when booting in SPL stage, then no need to bother which device is BOOT_DEVICE_MMC1/2. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx: imx8mq: add init_nand_clkPeng Fan
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF, so we still use legacy mode to configure the clock. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx8m: clock: improve irq response latencyPeng Fan
Improve the IRQ response latency by setting GIC root clock source to sys_pll2_200m from osc. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx8m: imx8mq: get chip rev for B1 revisionPeng Fan
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id. It returns a magic number 0xff0055aa. update get_cpu_rev to support it, and enable ocotp clock to access ocotp. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03video: mxsfb: set gd->fb_baseSébastien Szymanski
Set gd->fb_base so it can be shown with bdinfo command. Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-11-03opos6uldev: migrate to DM_VIDEOSébastien Szymanski
Migrate to DM_VIDEO, update the device tree and remove code that is no longer necessary. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03imx6ul: opos6ul: migrate to DM_ETHSébastien Szymanski
Migrate to DM_ETH and remove code that is no longer necessary. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03imx: update i.MX8MQ device treesPatrick Wildt
This updates the i.MX8MQ device trees and, necessarily, also the i.MX8MQ clock bindings. These are taken verbatim from from the Linux kernel version v5.4-rc2, which three small changes which were already part of the previous device tree: * Keep the PSCI reserved memory range * Keep the alias for ethernet, so that the MAC address can be set * Keep the modified #include for the IOMUXC pins Signed-off-by: Patrick Wildt <patrick@blueri.se> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-11-03mccmon6: defconfig: nor: Enable usage of *_TINY_* drivers in SPLLukasz Majewski
After this change the SPL size has been reduced from 38K to 34K. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Convert mccmon6 to use fitImage instead of uImage+DTBLukasz Majewski
This commit enabled support for fitImage on mccmon6 when we switch to DT/DTS (including falcon mode). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03spl: nor: Provide falcon boot support for NOR memoriesLukasz Majewski
This commit adds falcon boot support (by also copying args necessary for booting) to the SPL NOR memory driver. After this change it is possible to use the falcon boot in the same way as on NAND memories. The necessary configs (i.e. CONFIG_CMD_SPL_NOR_OFS) are now defined in Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-11-03ARM: imx: Decouple mccmon6's SPL and u-boot proper codeLukasz Majewski
The mccmon6 has been used a "mixed" approach between SPL and U-Boot proper sources. This commit decoupes SPL and u-boot proper, which allows clear distinction between those two code bases and facilitates conversion to DM/DTS on this particular board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Convert mccmon6 to use DM/DTS in the u-boot properLukasz Majewski
This commit converts mccmon6's u-boot proper (in a single commit to avoid build breaks) to use solely DM/DTS. The DTS description of the mccmon6 has been ported from Linux kernel (v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03imx: Enable RTC (ds1307) support in the U-Boot proper on TPC70 boardLukasz Majewski
The TPC70 is equipped with DS1307 RTC device. Add code to enable support for it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx6: DHCOM i.MX6 PDK: spl: Add eMMC initialization to SPL codeClaudius Heine
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0). Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03ARM: imx6: DHCOM i.MX6 PDK: defconfig: Enable MMC support of SPLClaudius Heine
Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03ARM: imx6: DHCOM i.MX6 PDK: fix board_boot_modes emmc entryClaudius Heine
The board_boot_modes contained the wrong values for the emmc entry. The eMMC here is connected over a 8-bit bus. This change allows to use the 'bmode emmc' command to boot from emmc. Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03watchdog: imx: Use immediate reset bits for expire_nowRobert Hancock
The expire_now function was previously setting the watchdog timeout to minimum and waiting for the watchdog to expire. However, this watchdog also has bits to trigger immediate reset. Use those instead, like the Linux imx2_wdt driver does. Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
2019-11-03watchdog: imx: Add DT ext-reset handlingRobert Hancock
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the device tree to specify whether the board design should use the external reset instead of the internal reset. Use this boolean to determine which mode to use rather than using external reset unconditionally. For the legacy non-DM mode, the external reset is always used in order to maintain the previous behavior. Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
2019-11-03ARM: dts: imx6ull-colibri: pre-reloc for uart pinmux modesIgor Opaniuk
Add u-boot,dm-pre-reloc properties for uart pinmux configuration nodes, which enables UART as early as possible (before relocation). Without this we miss almost the half of output (U-boot version, CPU defails, Reset cause, DRAM details etc.). Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm") Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-11-03ARM: dts: imx6ull-colibri: change hierarchy of DTS filesIgor Opaniuk
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to keep original imx6ull-colibri.dts in sync with Linux. Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi + additionally fix checkpatch warnings. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-11-03arm: mxs: Increase VDDD voltage to match specificationMarek Vasut
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating Conditions, page 16, the VDDD should be set to 1.55V when the CPU is operating at 454MHz. This is the case in U-Boot, hence increase the VDDD voltage. This fixes instability when performing TFTP transfers. Increase the brownout threshold to 1.4V. The documentation recommends 1.45V setting for the brownout, however, this triggers failure during power block init, so keep the brownout slightly lower. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-11-03ARM: imx: Use IMX6_SRC_GPR10_BMODE instead of magic numberClaudius Heine
Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03ARM: imx: Fix bmode detection from grp10Claudius Heine
imx6_is_bmode_from_gpr9 always returns false, because IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return. This moves the function body into imx6_src_get_boot_mode, since that is the only one using it and it is on the same abstraction level (accessing registers directly). Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03arm: dts: Add devicetree support for iMXQXP AI_ML boardManivannan Sadhasivam
Add devicetree support for iMXQXP AI_ML board from Einfochips. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-11-03i.MX6: nand: extend nandbcb command for imx6UL(L)Parthiban Nallathambi
Firmware Configuration Block(FCB) for imx6ul(l) needs to be BCH encoded. Signed-off-by: Parthiban Nallathambi <pn@denx.de> Acked-by: Shyam Saini <shyam.saini@amarulasolutions.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx: defconfig: Enable CONFIG_SPL_FORCE_MMC_BOOT on display5Lukasz Majewski
After the following commit: commit 772b55723bcb ("imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon mode") it is possible to set the CONFIG_SPL_FORCE_MMC_BOOT flag, which allows using MMC device as boot device regardless of the device used by Boot ROM (FBL) as the first boot medium. Display5 board needs this flag set to allow falcon boot from eMMC device. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03net: ti: am65x-cpsw: fix mac tx internal delay for rgmii-rxid modeGrygorii Strashko
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping default value (enabled) for MAC TX internal delay when "rgmii-rxid" interface mode is selected. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-11-03net: ti: cpsw: fix mac tx internal delay for rgmii-rxid modeGrygorii Strashko
Now TI CPSW driver will disable MAC TX internal delay for PHY interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping default value (enabled) for MAC TX internal delay when "rgmii-rxid" interface mode is selected. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-11-03net: ti: cpsw: add support for standard eth "max-speed" dt propertyGrygorii Strashko
This patch adds support for standard Ethernet "max-speed" DT property to allow PHY link speed limitation. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-11-03net: ti: cpsw: move parsing of dt port's parameters in separate funcGrygorii Strashko
Move parsing of dt port's parameters in separate func for better code readability. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-11-03net: ti: cpsw: enable 10Mbps link speed support in rgmii modeGrygorii Strashko
According to TRMs the 10Mbps link speed is supported in RGMII only when CPSW2G MAC SL is configured for External Control ("in band") mode CPSW_SL_MACCTRL.EXT_EN(18) = 1. Hence update cpsw_slave_update_link() to follow documentation. [1] https://patchwork.kernel.org/patch/10285239/ Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-11-03arm: dts: am335x: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Heiko Schocher <hs@denx.de> Cc: Felix Brack <fb@ltec.ch> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-11-03arm: dts: am437x: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
2019-11-03arm: dts: dra7: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
2019-11-03mx6: clock: Introduce disable_ipu_clock()Fabio Estevam
Introduce disable_ipu_clock(). This is done in preparation for configuring the NoC registers on i.MX6QP in SPL. Afer the NoC registers are set the IPU clocks can be disabled. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-11-03mx6: clock: Use setbits_le32()Fabio Estevam
The code can be made simpler by using setbits_le32(), so switch to it. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-11-03x86: Quieten TPL's jump_to_image_no_args()Simon Glass
We already a message indicating that U-Boot is about to jump to SPL, so make this one a debug() to reduce code size. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: Don't print CPU info in TPLSimon Glass
We don't need to do this and it is done (in more detail) in U-Boot proper. Drop this to save code space. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: Move CPU init to before spl_init()Simon Glass
At present we call spl_init() before identifying the CPU. This is not a good idea - e.g. if bootstage is enabled then it will try to set up the timer which works better if the CPU is identified. Put explicit code at each entry pointer to identify the CPU. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: Add a CPU init function for TPLSimon Glass
For TPL we only need to set up the features and identify the CPU to a basic level. Add a function to handle that. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: tpl: Add a fake PCI busSimon Glass
In TPL we try to minimise code size so do not include the PCI subsystem. We can use fixed BARs and drivers can directly program the devices that they need. However we do need to bind the devices on the PCI bus and without PCI this does not ordinarily happen. As a work-around, define a fake PCI bus which does this binding, but no other PCI operations. This is a convenient way to ensure that we can use the same device tree for TPL, SPL and U-Boot proper: TPL - CONFIG_TPL_PCI is not set (no auto-config, fake PCI bus) SPL - CONFIG_SPL_PCI is set (no auto-config but with real PCI bus) U-Boot - CONFIG_PCI is set (full auto-config after relocation) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: spl: Support init of a PUNITSimon Glass
The x86 power unit handles power management. Support initing this device which is modelled as a new type of system controller since there are no operations needed. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: timer: Use a separate flag for whether timer is initedSimon Glass
At present the value of the timer base is used to determine whether the timer has been set up or not. It is true that the timer is essentially never exactly 0 when it is read. However 'time 0' may indicate the time that the machine was reset so it is useful to be able to denote that. Update the code to use a separate flag instead. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03x86: timer: Set up the timer in timer_early_get_count()Simon Glass
This function can be called before the timer is set up. Make sure that the init function is called so that it works correctly. This is needed so that bootstage can work correctly in TPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03spl: Add a size check for TPLSimon Glass
We have the ability to enforce a maximum size for SPL but not yet for TPL. Add a new option for this. Document the size check macro while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03dm: doc: Correct of-platdata driver nameSimon Glass
Add a note about the driver name in the of-platdata documentation since the naming must follow the compatible string. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-11-03spi: Add support for memory-mapped flashSimon Glass
On x86 platforms the SPI flash can be mapped into memory so that the contents can be read with normal memory accesses. Add a new SPI method to find the location of the SPI flash in memory. This differs from the existing device-tree "memory-map" mechanism in that the location can be discovered at run-time. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-28 13:47:18 +0000