| Age | Commit message (Collapse) | Author |
|---|
|
Otherwise, we see this:
In file included from include/configs/zynq-common.h:183:0,
from include/config.h:5,
from include/common.h:21,
from env/common.c:11:
include/config_distro_bootcmd.h:319:2: error: expected ?}? before ?BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE?
BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE
^
include/config_distro_bootcmd.h:319:2: note: in definition of macro ?BOOTENV_DEV_NAME_PXE?
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This reverts the parts of commit 3b3ea2c56ec4bc5588281fd103c744e608f8b25c
where it changed the EFI dependency on NET.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
No commands are necessary to have a network stack.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
The BOOTP options used to be and should still be default for all boards
with CMD_NET enabled. One should not be forced to use DISTRO_DEFAULTS to
get them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
Improve the documentation and correct the listed dependencies.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
Commit 3b3ea2c56ec4bc5 ("Kconfig: cmd: Make networking command dependent on NET")
removed the help documentation from the README but didn't add it back to Kconfig.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
The options were pretty unhelpful, so improve them some.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
|
|
Move DHCP to directly follow BOOTP so that Kconfig can show the
dependency as a hierarchy.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
Options that controlled the tftp and bootp commands depended on their
commands, but lived in the net menu.
Move them so they are in a consistent location.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
|
|
PING requires CMD_NET, not NET.
Also, CMD_NET already depends on NET, so no need to directly depend
on it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Previously, CMD_NET was an alias for 2 commands (bootp and tftpboot) and
they we not able to be disabled. Separate out those 2 commands and move
CMD_NET up to the menu level, which more accurately represents the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
|
|
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add i.MX6UL/SX/SL compatible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.
To i.MX28, adapt to use the new config
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
To platforms has two enet interface, using dev->seq could
avoid conflict.
i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.
In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.
This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
|
|
|
|
The Gen3 kernel images are often above 8 MiB, increase the
maximum kernel size to 64 MiB to future-proof it, just like
many other ARM64 boards do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Fix up the memory map on Gen3 to match datasheet properly.
This simplifies the memory map setup as well, since we do
no longer need this massive complexity.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The QSPI controller on RCar Gen2 has 32byte FIFO. Instead of doing
the SPI transmission 1 byte at time, if there is a 32byte chunk of
data to be transferred, fill the FIFO completely and then transfer
the data to/from the FIFO. This increases the SPI NOR access speed
significantly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Replace the ad-hoc endless loops with wait_for_bit() with
reasonable timeout. Note that the loops had internal 10uS
delays, although there is no reason for those on this HW,
so they are dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Waiting for SPBDCR == 1 is not required and is covered by the
subsequent wait for SPSR_SPRFF, so drop this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Just replace unsigned {char,short,long} with u{8,16,32},
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Add driver for the RPC block in SPI-flash mode. This driver allows
access to a SPI NOR flash attached to the RPC block and does not
support RPC in Hyperflash mode. Note that this block is extremely
selective when communicating with the SPI NOR.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add driver for the RPC block in Hyperflash mode. This driver allows
access to a CFI Hyperflash attached to the RPC block and does not
support RPC in SPI mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The IP requires some time to recuperate after the IO pin
properties were changed. Add a delay to assure this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix minor rebase omission, the else was missing which triggered
two accesses to the register on 64bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Make sure to wait for the command to complete altogether, including
the trailing 8 clock cycles. This prevents the driver for accidentally
writing the CMD register too fast before the previous command fully
completed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The HOST_MODE register must be set to 0 when the IP is operated in 16bit
mode, otherwise 16bit access to the data FIFO may fail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
There are only a few registerse used in the 16bit mode which are
32bit internally. Special-case only those in the IO accessors and
always write both halves. Any other register access is protected
from accidentally overwriting neighboring register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Enable the HS200 on RCar Gen3 platforms, since the SDHI core supports it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add code for PHY tuning required for SDR104/HS200 support on Renesas RCar.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Export the matsu_sd_{read,write}l() common register access
functions, so that they can be used by other drivers sharing
the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Factor out the regulator handling into set_ios and add support for
selecting pin configuration based on the voltage to support UHS modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handle the controller version even if quirks are set. The controller in
Renesas Gen3 SoCs does provide the version register, which indicates a
controller v10 and the controller does support internal DMA and /1024
divider.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handle bus width 0 as 1-bit bus to assure valid content of
MATSU_SD_OPTION register WIDTH field.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The DMA READ completion flag position differs on Socionext and Renesas
SoCs. It is bit 20 on Socionext SoCs and using bit 17 is a hardware bug
and forbidden. It is bit 17 on Renesas SoCs and bit 20 does not work on
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
On the Renesas version of the IP, the /1 divider is realized by
setting the clock register [7:0] to 0xff instead of setting bit
10 of the register. Check the quirk and handle accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add a quirk to identify that the controller is Renesas RCar variant
of the Matsushita SD IP and another quirk indicating it can support
Renesas RCar HS200/HS400/SDR104 modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Drop the ad-hoc DT caps parsing in favor of common framework function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The Renesas RCar Gen2 chips have a mix of 32bit and 16bit variants
of the IP. There is no DT property which allows discerning those,
so what Linux does is it checks the size of the register area and
if it is 0x100, the IP is 16bit, otherwise the IP is 32bit. Handle
the distinction the same way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Certain instances of the SD IP require more elaborate digging
in the DT to figure out which variant of the SD IP is in use.
Allow explicit passing of the quirks into the probe function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add support for 16bit mutation of the Matsushita SD IP. Since some
registers are internally 32bit, the matsu_sd_{read,write}l() has
to special-case this 16bit variant a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Drop useless check in matsu_sd_{read,write}q(), this is only ever
called to read the data from FIFO and only when 64bit variant of
the block is used anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add macros to generate the FIFO accessors, since the code is almost
the same with only minor differences. This is done in preparation
for adding 16bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
