summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-14imx: imxrt1050-evk: Add support for the NXP i.MXRT1050-EVKGiulio Benetti
This commit adds board support for i.MXRT1050-EVK from NXP. This board is an evaluation kit provided by NXP for i.MXRT105x processor family. More information about this board can be found here: https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK The initial supported/tested devices include: - Debug serial - SD Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14imx: Add basic support for the NXP IMXRT10xx SoC familyGiulio Benetti
Add i.IMXRT family basic support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14mmc: fsl_esdhc: add compatible for fsl, imxrt-usdhcGiulio Benetti
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms with CONFIG_DM_MMC=y. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14mmc: fsl_esdhc: make if(CONFIG_IS_ENABLED(CLK)) an #if statementGiulio Benetti
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK instead. So building could result in failure due to missing mxc_get_clock(). Make if(CONFIG_IS_ENABLED(CLK)) an #if statement. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14ram: add SDRAM driver for i.MXRT SoCsGiulio Benetti
Add SDRAM driver for i.MXRT SoCs. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14serial_lpuart: add support for i.MXRTGiulio Benetti
Add i.MXRT compatible string and cpu type support to lpuart driver, to use little endian 32 bits configurations. Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART FIFO register is bit 3, so this definition should change to 0x08 as done for i.MX8. It needs also to set baudrate the same way as i.MX8 does. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14serial_lpuart: add clock enable if CONFIG_CLK is definedGiulio Benetti
This driver assumes that lpuart clock is already enabled before probing but using DM only lpuart won't be automatically enabled so add clk_enable() when probing if CONFIG_CLK is defined. If clock is not found, because DM is not used, let's emit a warning and proceed, because serial clock could also be already enabled by non DM code. If clock is found but cna't be enabled then return with error. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14ARM: dts: imxrt1050: add dtsi fileGiulio Benetti
Add dtsi file for i.MXRT1050. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14gpio: mxc_gpio: add support for i.MXRT1050Giulio Benetti
Add i.MXRT1050 support, there are 5 GPIO banks. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14pinctrl: add i.MXRT driverGiulio Benetti
Add i.MXRT pinctrl driver. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: add i.IMXRT1050 clk driverGiulio Benetti
Add i.MXRT1050 clk driver support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pfd: add set_rate()Giulio Benetti
Implement set_rate() for pfd. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add support for PLLV3_AV typeGiulio Benetti
Add support for PLLV3 AV type. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pllv3: add PLLV3_SYS supportGiulio Benetti
Add PLLV3_SYS support by adding set/get_rate() for PLLV3_SYS but keeping generic enable()/disable(). Add a different driver because ops are different respect to GENERIC/USB. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add set_rate() supportGiulio Benetti
Add generic set_rate() support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add disable() supportGiulio Benetti
Add disable() support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add enable() supportGiulio Benetti
Before set_rate() pllv3 needs enable() to power the pll up. Add enable() taking into account different power_bit and different powerup_set, because some pll needs its power_bit to be set or reset to be powered on. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pllv3: set div_mask differently if PLLV3 is GENERIC or USBGiulio Benetti
div_mask is different for GENERIC and USB pll, so set it according. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: register PLLV3 GENERIC and USB as 2 different clocksGiulio Benetti
Better to register the 2 clock as 2 different drivers because they work slightly differently depending on power_bit and powerup_set bits coming on next patches. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14armv7m: cache: add mmu_set_region_dcache_behaviour() stub for compatibilityGiulio Benetti
Since some driver requires this function add it as an empty stub when DCACHE is OFF. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14spl: fix entry_point equal to load_addrGiulio Benetti
At the moment entry_point is set to image_get_load(header) that sets it to "load address" instead of "entry point", assuming entry_point is equal to load_addr, but it's not true. Then load_addr is set to "entry_point - header_size", but this is wrong too since load_addr is not an entry point. So use image_get_ep() for entry_point assignment and image_get_load() for load_addr assignment. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14imx: dts: imx8dx: add I2C IPG clock for bus 0 and 2Anatolij Gustschin
IPG clock description is missing for I2C0 and I2C2 busses, add it. Otherwise we see -ENODATA error when trying to get I2C clock for these busses. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-01-14clk: imx8qxp: extend to support getting I2C IPG clockAnatolij Gustschin
Since commit d02be21d3004 ("i2c: imx_lpi2c: add ipg clk") getting I2C clocks doesn't work. Add I2C IPG clock IDs to related switch statements to fix it. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Lukasz Majewski <lukma@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-01-14ARM: dts: imx6ul-14x14-evk: Pass the "broken-cd" propertyFabio Estevam
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card detect pin on the eSDHC2 port. In such cases the "broken-cd" property must be passed, otherwise the card cannot be detected. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14mmc: fsl_esdhc_imx: Handle the "broken-cd" propertyFabio Estevam
When no GPIO is used to read the card detect status the following error is seen: MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... MMC: no card present *** Warning - No block device, using default environment Fix it by handling the "broken-cd" property in the same way that drivers/mmc/sdhci.c does, which considers that the SD card is present when the "broken-cd" property is passed. Tested on a imx6ul-evk board. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14pico-imx7d: Convert to DM_ETHJoris Offouga
Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14pico-imx7d: Disable USB_ETHER support for bl33 defconfigJoris Offouga
For DM_ETH support , it's require to disable this config. When this config is enable, This generate a error with spl in linker script Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14mx6ul_14x14_evk: Fix SPL boot hangFabio Estevam
Currently the following SPL hang is observed: U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Fix it by moving the eSDHC2 initialization to SPL. While at it, since this board uses DM_MMC all the esdhc board code can be removed to make the code simpler. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-14imx: imx8qxp_mek: update READMEPeng Fan
Update README to use 4.19.35_1.1.0 released firmware images. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-14wandboard: Do not print error message when PMIC is absentFabio Estevam
Only the wandboard revD1 boards have PMIC, so when running on a wandboard of different revision the following error is always shown on every boot: pmic_get() ret -19 Instead of printing this error message, move it to debug level instead. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-14imx8qxp_mek: Select CONFIG_NET_RANDOM_ETHADDRFabio Estevam
Some i.MX8QXP MEK boards do not have MAC address stored and hang during eth driver probe: Error: ethernet@5b040000 address not set. (Board hangs) To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that a valid MAC address can be used in such case. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-14imx: add imx8x based deneb boardAnatolij Gustschin
Add support for Capricorn Deneb SoM variant. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-14imx: add imx8x capricorn giedi boardAnatolij Gustschin
Add support for i.MX8X based Capricorn Giedi SoM. Supported interfaces: GPIO, ENET, eMMC, I2C, UART. Console output: U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) Trying to boot from MMC1 Load image from MMC/SD 0x3e400 U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07 CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C Model: Siemens Giedi Board: Capricorn Boot: MMC0 DRAM: 1022 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial@5a080000 Out: serial@5a080000 Err: serial@5a080000 Net: eth1: ethernet@5b050000 [PRIME] Autobooting in 1 seconds, press "<Esc><Esc>" to stop Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-11travis: Switch to QEMU v4.2.0 globallyTom Rini
Given our tests in GitLab / Azure we can use QEMU v4.2.0 for all platforms now. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-10gitlab/azure: Update to latest containerTom Rini
- Updated base snapshot - QEMU v4.2.0 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-10Merge branch '2020-01-10-master-imports'Tom Rini
- Android image support enhancements - Assorted ARM fixes and enhancements - m68k update
2020-01-10cmd: adtimg: Refactor usage styleEugeniu Rosca
Trying to extend 'adtimg' functionality [1], we've been severely hit by a major limitation in the command's usage scheme. Specifically, the command's user interface appears to be too centric to getting the DTB/DTBO entry [3] based on the index of the desired DT in the image, which makes it really difficult retrieving the DT entry based on alternative criteria (e.g. filtering by id/rev fields), the latter being demanded by real life customer use-cases [1]. This went to the point of receiving below feedback from Sam [2]: -- snip -- As for 'dtimg' command: after giving it some thought, I think not much people using it yet. So in this particular case I don't have some strong preference, and if you think the 'dtimg' interface is ugly, and it overcomes "don't break interfaces" rule, maybe now is a good time to rework it (before it gets widely used). -- snip -- Given the above, rework the usage pattern from [4] to [5], in order to allow an intuitive enablement of "by id|rev" DT search [6]. [1] https://patchwork.ozlabs.org/cover/1202575/ ("cmd: dtimg: Enhance with --id and --rev options (take #1)") [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 [3] https://source.android.com/devices/architecture/dto/partitions [4] Old usage adtimg dump <addr> - Print image contents adtimg start <addr> <index> <varname> - Get DT address by index adtimg size <addr> <index> <varname> - Get DT size by index [5] New usage adtimg addr <addr> - Set image location to <addr> adtimg dump - Print out image contents adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] - Get DT address/size/index by id|rev fields Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2020-01-10cmd: adtimg: Rename internal symbolsEugeniu Rosca
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming consistency in the internal implementation of 'adtimg.c'. No functional change intended. Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-01-10dtimg/am57xx_evm_defconfig: Rename dtimg to adtimgEugeniu Rosca
Rename the existing 'dtimg' command to 'adtimg', in order to: - Suggest the Android origins and scope - Be consistent with the upcoming 'abootimg' command (naming suggested by Simon [*]) The change in _not_ backward compatible, but its benefits outweigh its downsides, given that we don't expect active users of 'dtimg' today. Perform the rename in several steps: 1. Rename *.c file and Kconfig symbol. This should allow 'git log --follow' to properly track the history of 'adtimg.c' 2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c' ELF comparison [**] before and after shows no functional change. [*] https://patchwork.ozlabs.org/patch/1182212/#2291600 [**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o) Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2020-01-10virtio: fix typo devicdHeinrich Schuchardt
%s/devicd/device Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-01-10arm: cpu: armv8: add support for arm psci reset2.Rajesh Ravi
Current U-Boot has only support for psci reset. Adding support for arm psci reset2 allows passing of reset level and other platform sepcific parameters like strap settings to lowlevel psci implementation. Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
2020-01-10arch: arm: Program GIC LPI configuration tableBharat Kumar Reddy Gooty
Programs the following: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
2020-01-10mkimage: simplify fit_check_params()Heinrich Schuchardt
fit_check_params() wants at least two of dflag, fflag, and lflag set. Simplify the logical constraint checking this. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-01-10cmd/eeprom.c: prepend 0x to hex numbers in output message formatKlaus H. Sorensen
If the numbers do not happen to contain any digits from [a-f], it's not clear that they are base 16. Signed-off-by: Klaus H. Sorensen <khso@prevas.dk> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
2020-01-10test/cmd_ut.c: fix cmd_ut_categoryPhilippe Reynes
In the function cmd_ut_category, the prefix is used with the function strncmp to know if the prefix should be removed from the test name, even if the prefix is NULL. To avoid this issue, we consider that a prefix NULL mean no prefix. So we only try to remove the prefix from the test_name if the prefix is not NULL, then we avoid to call the function strncmp with a NULL prefix. Reported-by: Coverity CID 281110 Fixes: 4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category") Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-10gcc-9: silence 'address-of-packed-member' warningAndy Shevchenko
GCC 9.x starts complaining about potential misalignment of the pointer to the array (in this case alignment=2) in the packed (alignment=1) structures. Repeating Linus' Torvalds commit 6f303d60534c in the Linux kernel. Original commit message: We already did this for clang, but now gcc has that warning too. Yes, yes, the address may be unaligned. And that's kind of the point. This in particular hides the warnings like drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 545 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 550 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 555 | collect_langs(sp, s->wData); Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-10boards/km_arm: enable support for Macronix SPI NOR flashHolger Brunck
The M25P80 and M25P32 SPI flashes from Numonix/Micron will be replaced by Marconix MX25L80 and MX25L32 flashes. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10arm/km: remove board KMCOGE3UNHolger Brunck
This target is out of maintenance and can be removed. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10km/boards: add MAC address offset as argument to ivm_populate_envHolger Brunck
For upcoming SECU board we have different MAC address offsets depending on which functional unit we are running. In this case we need to pass this value to the ivm_populate_env function instead of using the hard coded config option there. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10km/boards: fix typo for MAC address offset config optionHolger Brunck
This patch only fixes a typo. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2025-02-01 18:06:07 +0000