summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-05-09board: at91sam9263ek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9263ek: Clean up codeWenyou Yang
Because the introduction of the pinctrl and clk drivers and the device tree files, remove unneeded hard coded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9263ek: Update for DT and DM supportWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9rlek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9rlek: Clean up codeWenyou Yang
Since the introduction of the pinctrl and clk drivers and the device tree files, remove unneeded hard coded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9rlek: Update for DT and DM supportWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9260ek/9g20ek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9260ek: Clean up codeWenyou Yang
Since the introduction of the pinctrl and clk drivers and the device tree files, remove unneeded hard coded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9260ek/9g20ek: Update for DT and DMWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9m10g45ek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9m10g45ek: Clean up codeWenyou Yang
Since the introduction of the pinctrl and clk drivers and the device tree files, remove unneeded hard coded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9m10g45ek: Update to support DM/DTWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Because the limitation of internal SRAM size, the SPL with driver model can't be supported, disable the SPL option. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9n12ek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9n12ek: Clean up codeWenyou Yang
Since the introduction of the pinctrl and clk driver and the device tree files, remove unneeded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9n12ek: Update for DT and DM supportWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Because the limitation of internal SRAM size, the SPL with driver model can't be supported, disable the SPL option. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9x5ek: Enable early debug UARTWenyou Yang
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09board: at91sam9x5ek: Clean up codeWenyou Yang
Since the introduction of the pinctrl and clock driver and the device tree files, remove unneeded hard coded related code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: at91sam9x5ek: Update to support DM/DTWenyou Yang
Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Because the limitation of internal SRAM size, the SPL with driver model can't be supported, disable the SPL option. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9263ekWenyou Yang
The device tree source files of at91sam9263ek boards are copied from the Linux v4.10, do the changes as below. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used in board_init_f stage. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9rlekWenyou Yang
The device tree source files of at91sam9rlek boards are copied from the Linux v4.10, do the changes as below. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used in board_init_f stage. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9260ek/9g20ekWenyou Yang
The device tree source files of at91sam9g20ek and at91sam9260ek boards are copied from the Linux v4.10, do the changes below. - Fix the build error for the usb0 node. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used in board_init_f stage. - Add the clk pinctrl of the mmc0 node. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9m10g45ekWenyou Yang
The device tree source files of at91sam9m10g45ek boards are copied from the Linux v4.10, do the changes as below. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Add the "u-boot,dm-pre-reloc" property to determine which nodes are used by the board_init_f stage. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9n12ekWenyou Yang
The device tree source files of at91sam9n12ek boards are copied from the Linux v4.10, do the changes as below. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Change the compatible of the spi flash to "spi-flash". - Add the spi0 aliases. - Fix the pinctrl-names of mmc0 node. - Add the "u-boot,dm-pre-reloc" property to determine which nodes are used by the board_init_f stage. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09ARM: dts: at91: Add dts files for at91sam9x5ekWenyou Yang
The device tree source files of at91sam9x5ek board are copied from the Linux v4.10, do the changes below. - Add the reg property for the pinctrl node. - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's slibling nodes, instead of the child nodes. - Add the "u-boot,dm-pre-reloc" property to determine which nodes are used by the board_init_f stage. - Change the compatible of the spi flash to "spi-flash". - Add the spi0 aliases. - Fix the compilation warnings. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09serial: atmel_usart: Add clk supportWenyou Yang
Add the clock support. Note that the clock handling of the DBGU peripheral is different from the USART. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09serial: atmel_usart: Fix early debug not work in SPLWenyou Yang
Add the uart init function to be used on both probe and the early debug uart init. For the latter, the input clock should be from CONFIG_DEBUG_UART_CLOCK. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09clk: at91: Align the at91 pmc's compatiblesWenyou Yang
Align the at91 pmc's compatibles with kernel. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-05-09clk: at91: Align clk-master compatibles with kernelWenyou Yang
Add the compatible "atmel,at91rm9200-clk-master" to align with the kernel. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09clk: at91: Enhance the peripheral clockWenyou Yang
Enhance the peripheral clock to support both at9sam9x5's and at91rm9200's peripheral clock via the different compatibles. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09net: macb: Align the compatibles with kernelWenyou Yang
Add the compatibles to align with the kernel. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-05-09net: macb: Add remove callbackWenyou Yang
To avoid the failure of mdio_register(), add the remove callback to unregister the mii_dev when removing the ethernet device. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Fixed up unused variable warning, e.g. for gurnard: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09configs: sama5d3xek: add default config for CMP boardWenyou Yang
The sama5d36ek CMP board is the variant of sama5d3xek board. It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and some power rails. The board is mainly used to measure the power consumption. As all those changes are done in at91bootstrap, in U-Boot, only use another device tree file, no code needed to change. As there is additional power consumption when enbling the USB Host and USB device, for the power consumption measurement intention, disable the USB host and device. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09board: sama5d4ek: fix DD2 configurationWenyou Yang
Fix the DDR2 configuration to make SPL work. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09configs: sama5d2_xplained: update for SPLWenyou Yang
Enable config options to support the SPL, increase the malloc memory size for the SPL and board_init_f stage and increase the memory space for the SPL binary. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09board: sama5d2_xplained: remove unnecessary header filesWenyou Yang
Remove the unnecessary header files. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09board: sama5d2_xplained: remove uart1 initWenyou Yang
Due to the pin configuration and clock enabling is handling by the driver, remove the unneeded hardcode uart1 init during board_early_init_f stage. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09board: sama5d2_xplained: clean up macb init codeWenyou Yang
Because the MACB driver supports the driver model and device tree, the pins configuration and clock enabling are handled by the pinctrl driver and clock driver, remove this hardcoded init code. The USB Ether init code is removed as well. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09configs: sama5d2_xplained: enable CONFIG_DM_ETHWenyou Yang
Enable CONFIG_DM_ETH to make MACB to support driver model. Because the USB Ether doesn't support driver model so far, remove this feature. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09ARM: dts: sama5d2_xplained: update for SPLWenyou Yang
Add the "u-boot,dm-pre-reloc" property to determine which nodes which are needed by SPL and by the board_init_f stage. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09ARM: dts: sama5d2: add clock property for uart1 nodeWenyou Yang
Add clock property for uart1 node. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2017-05-09p1_p2_rdb: Fix unused variable warningTom Rini
With gcc-6 we see a warning that sysclk_tbl is defined but unused, so remove it. Cc: York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-09dm: Update Simple Watchdog uclassMaxim Sloyko
- Remove "probe" function from sandbox wdt driver - Fix include order Fixes: 0753bc2d30d7 ("dm: Simple Watchdog uclass") Signed-off-by: Maxim Sloyko <maxims@google.com> [trini: Create as the delta between v1 (applied) and v2 (should have applied)]. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-09ARM: mvebu: switch db-88f6820-amc to DM for i2cChris Packham
Move existing configuration from header file to defconfig or dts as appropriate. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09arm64: mvebu: Fix the bubt comamnd NAND device supportKonstantin Porotchkin
Fix the NAND structures in bubt command according to latest changes in MTD API. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-09fix: nand: pxa3xx: Remove hardcode values from the driverKonstantin Porotchkin
Obtain NAND controller setup parameters from the device tree instead of using hardcoded values. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Scott Wood <oss@buserror.net> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-09fix: phy: marvell: cp110: pcie: update analog parameters according to latest ETPIgal Liberman
Add PCIE analog parameters initialization values according to latest ETP. Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09fix: phy: marvell: cp110: rename comphy_index to cp_indexIgal Liberman
No functional change. The variable name "comphy_index" is misleading, it represents cp index and not comphy index. Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09fix: phy: marvell: cp110: sfi: update analog parameters according to latest ETPIgal Liberman
Add SFI analog parameters initialization values according to latest ETP. Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09phy: marvell: print comphy status even when it's disconnectedStefan Roese
since now the COMPHY can also be ignored, we must know the state of the COMPHY. we cannot assume anymore that a missing COMPHY is unconnected. Signed-off-by: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-28 08:43:02 +0000