summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-09-22regulator: pbias: Add PBIAS regulator for proper voltage switching on MMC1Jean-Jacques Hiblot
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1 IO cells. Without this bias voltage these I/O cells can not function properly. The PBIAS cell is controlled by software. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22dm: core: Add functions to get strings and the string count from a stringlistJean-Jacques Hiblot
dev_read_string_count() is used to get the number of strings in a stringlist. dev_read_string_index() is used to get a string in the stringlist based on its position in the list. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-09-22mmc: uniphier-sd: Add support for R8A7795 and R7A7796Marek Vasut
Add OF match entries and quirks for Renesas RCar Gen3 controllers into the driver. The IP this driver handles is in fact Matsushita one and in used both in Socionext and Renesas chips. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-22mmc: uniphier-sd: Add support for quirksMarek Vasut
Check if the OF match has any associated data and if so, use those data as the controller quirks, otherwise fallback to the old method of reading the controller version register to figure out the quirks. This allows us to supply controller quirks on controllers which ie. do not have version register. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-22mmc: uniphier-sd: Add support for 64bit FIFOMarek Vasut
The Renesas RCar Gen3 contains the same controller, originally Matsushita. This patch adds support for handling of the 64bit FIFO on this controller. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-22mmc: uniphier-sd: Add support for 64bit controllerMarek Vasut
The Renesas RCar Gen3 contains the same controller, originally Matsushita, yet the register addresses are shifted by 1 to the left. The whole controller is also 64bit, including the data FIFOs and RSP registers. This patch adds support for handling the register IO by shifting the register offset by 1 in the IO accessor functions. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-22mmc: uniphier-sd: Factor out register IOMarek Vasut
This patch prepares the driver to support controller(s) with registers at locations shifted by constant. Pull out the readl()/writel() from the driver into separate functions, where the adjustment of the register offset can be easily contained. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-20Merge git://www.denx.de/git/u-boot-imxTom Rini
2017-09-20mx6sabresd: Add Serial Download Protocol supportFabio Estevam
Add Serial Download Protocol support (SDP), which allows loading SPL and u-boot.img via imx_usb_loader tool as explained in doc/README.sdp. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-09-20toradex: imx6: Move g_dnl_bind_fixup() into common SPL codeFabio Estevam
Instead of having every board file to add its own g_dnl_bind_fixup() implementation, move it to the common imx6 SPL code. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-09-20board: ge: bx50v3: set eth0 MAC addressIan Ray
Define i2c mux configuration. Add new vpd_reader which is used to read vital product data. Read VPD from EEPROM and set eth0 MAC address. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>
2017-09-20detect and setup solidrun hummingboard2Dennis Gilmore
The hummingboard2 is slightly different to the cubox i and to the hummingboard. The GPIO pin info to probe came from solidruns for of u-boot on github. https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589 I have tested on a hummingboard-edge witha imx6 solo and 512mb of ram. Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
2017-09-18Merge git://git.denx.de/u-boot-rockchipTom Rini
2017-09-18rockchip: puma_rk3399: increase serialno_str sizeKlaus Goger
Increase serialno_str to 17 bytes so it can hold the 16 bytes long serial nummer and the terminating null byte added by snprintf. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-09-18rockchip: ram: rk3399: update reg map for of-platdataKever Yang
After Simon's patch, the dtoc can work with 64bit address, so we need to fix reg number for it. Depend on Simon's patch set: https://patchwork.ozlabs.org/cover/807266/ Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: sdhci: update reg map for of-platdataKever Yang
After Simon's patch, the dtoc can work with 64bit address, so we need to fix reg number for it. Depend on Simon's patch set: https://patchwork.ozlabs.org/cover/807266/ Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: dts: rk3368: reduce the number of nodes seen in TPLPhilipp Tomsich
The RK3368 TPL stage always returns to the BootROM, so it has no need for the eMMC, SD and SPI nodes. This marks those nodes (that should be included in SPL, but not TPL) as 'u-boot,dm-spl'. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: rk3368: adjust DMC driver for 32/64bit-aware OF_PLATDATAPhilipp Tomsich
With the new 32/64bit-aware dtoc, the type of reg is fdt64_t and the OF_PLATDATA structure layout changes. This adjusts the DMC driver for the RK3368 to track these changes. For the time being (i.e. until regmap_init_mem_platdata works for the 64bit case), we won't use regmap_init_mem_platdata here and simply access of_plat.reg[] directly. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: timer: update for 32/64bit-aware OF_PLATDATAPhilipp Tomsich
With dtoc emitting fdt64_t for addresses (and region sizes), the array indices for accessing the reg[] array needs to be adjusted. This adjusts the Rockchip DM timer driver to correctly handle OF_PLATDATA given this new structure layout. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: defconfig: puma-rk3399: enable OF_LIVE (live tree)Philipp Tomsich
With the critical drivers ready for switching to a live tree, we can now enable it in the defconfig for the RK3399-Q7. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: efuse: change to use dev_read_addr_ptrPhilipp Tomsich
With the dev_read_addr_ptr function available, we can change the efuse driver to use it (and eliminate the explicit type-cast). Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: clk: rk3399: Convert to livetreePhilipp Tomsich
Update the clock driver for the RK3399 to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: dts: rk3399-puma: replace 'rockchip, vbus-gpio' with fixed regulatorPhilipp Tomsich
On the RK3399-Q7, we need to turn on the on-module USB hub before using the USB host interfaces (only the OTG interface is directly connected to the edge connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses a fixed regulator to turn on the USB hub. References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus" Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: clk: rk3399: add clk_enable function and support USB HOST0/1Philipp Tomsich
The generic ehci-driver (ehci-generic.c) will try to enable the clocks listed in the DTSI. If this fails (e.g. due to clk_enable not being implemented in a driver and -ENOSYS being returned by the clk-uclass), the driver will bail our and print an error message. This implements a minimal clk_enable for the RK3399 and supports the clocks mandatory for the EHCI controllers; as these are enabled by default we simply return success. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: rk3368: add the missing target and pinctrl config for sheep boardAndy Yan
Add the missing target and pinctrl config for rk3368 sheep board Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk3368: add ENV_MEM_LAYOUT to extra env settingsAndy Yan
Add the ENV_MEM_LAYOUT_SETTINGS to CONFIG_EXTRA_ENV_SETTINGS Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rk3288: Add Vyasa initial board supportJagan Teki
This patch adds support for Vyasa RK3288 initial board from Amarula Solutions. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk3399: spl: remove hard-coded addresses for GRF and SGRFPhilipp Tomsich
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL enabled: this allows the use of syscon to retrieve the addresses of GRF and SGRF (except for the early debug UART setup, which runs so early that the device-model is not initialised). This removes the hard-coded addresses and goes through syscon to retrieve the base-addresses of GRF and SGRF. After that, we use the structure definitions to locate the respective registers. In addition to this, the inclusion of header files is also cleaned up: - all headers are included at the beginning (there was a spurious inclusion of the grf header from within a function) - all #include statements for unused headers are removed - the remaining #include statements are sorted (while keeping common.h included in front) Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18rockchip: lion-rk3368: defconfig: resync w/ OF_LIVE and BOOTSTAGE enabledPhilipp Tomsich
This adds OF_LIVE and BOOTSTAGE support for the RK3368-uQ7 and regenerates the defconfig (picking up a few changes/reorderings) from upstream Kconfig changes. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: dts: rk3368-lion: add /chosen/tick-timerPhilipp Tomsich
To support bootstage recording, we want to mark our DM timer as the tick-timer; this triggers the support for 'trying harder' to read the timer in the Rockchip DM timer driver, even if the device model isn't ready yet. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: gpio: remove outdated/misleading commentPhilipp Tomsich
Remove a comment claiming that this driver only supports the RK3288, as we also use it on the RK3368, RK3399 and (most likely) on other variants. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Version-changes: 2 - use the dev_read_addr_ptr function in rk_gpio.c
2017-09-18rockchip: gpio: convert to livetreePhilipp Tomsich
Update the Rockchip GPIO-bank driver to support a live tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Version-changes: 2 - use the dev_read_addr_ptr function in rk_gpio.c
2017-09-18rockchip: i2c: Convert to livetreePhilipp Tomsich
Update the Rockchip I2C driver to support livetree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Heiko Schocher <hs@denx.de>
2017-09-18rockchip: rk8xx: remove unused header includesPhilipp Tomsich
Remove header file includes that have been left over after the conversion to livetree-support. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: sdhci: Convert to livetreePhilipp Tomsich
Update the Rockchip SDHCI wrapper to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Version-changes: 2 - use the dev_read_addr_ptr function in rockchip_sdhci.c
2017-09-18rockchip: spi: Convert to livetreePhilipp Tomsich
Update the Rockchip SPI driver to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: pinctrl: rk3368: Convert to livetreePhilipp Tomsich
Update the pinctrl driver for the RK3368 to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: clk: rk3368: Convert to livetreePhilipp Tomsich
Update the clock driver for the RK3368 to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Version-changes: 2 - use the dev_read_addr_ptr function in clk_rk3368.c
2017-09-18rockchip: timer: Convert to livetreePhilipp Tomsich
Update the Rockchip timer driver to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: timer: implement timer_get_boot_usPhilipp Tomsich
To make the Rockchip DM timer driver useful for the timing of bootstages, we need a few enhancements: - This implements timer_get_boot_us. - This avoids reinitialising the timer, if it has already been set up (e.g. by our TPL and SPL stages). Now, we have a single timebase ticking from TPL through the full U-Boot. - This adds support for reading the timer even before the device-model is ready: we find the timer via /chosen/tick-timer, then read its address and clock-frequency, and finally read the timeval directly). Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: mmc: convert to livetreePhilipp Tomsich
Update the Rockchip-specific wrapper for the Designware driver to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Version-changes: 2 - use the dev_read_addr_ptr function in rockchip_dw_mmc.c
2017-09-18net: phy: micrel: Convert to livetreePhilipp Tomsich
Update the Micrel KSZ90x1 driver for a live tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18net: designware: Convert to livetreePhilipp Tomsich
Update the Designware Ethernet MAC driver to support a live device tree. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18dm: core: add dev_read_addr_ptr()Philipp Tomsich
The dev_read_addr_ptr() mimics the behaviour of the devfdt_get_addr_ptr(), retrieving the first address of the node's reg-property and returning it as a pointer (or NULL on failure). Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18dm: timer: handle being called before dm_root is readyPhilipp Tomsich
When used with bootstage recording, dm_timer_init may be called surprisingly early: i.e. before dm_root is ready. To deal with this case, we explicitly check for this condition and return -EAGAIN to the caller (refer to drivers/timer/rockchip_timer.c for a case where this is needed/used). Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18dm: timer: Convert to livetreePhilipp Tomsich
This updates dm_timer_init to support a live tree and deals with some fallout (i.e. the need to restructure the code such, that we don't need multiple discontinuous #if CONFIG_IS_ENABLED blocks). Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18bootstage: adjust Makefile to allow including bootstage in SPL, but not in TPLPhilipp Tomsich
For timing our bootstages on the RK3368, which has a minimal TPL (and where we consequently don't want to time the bootstages) and a full-featured SPL (where we can bootstage recording), we need to adjust the Makefile. Use the $(SPL_TPL_) macro in the Makefile for bootstage.o Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: board: puma_rk3399: update README flash instructionsKlaus Goger
Puma supports other boot sources then SD-Card. Update README to include the required steps. * how to package a SPI-NOR SPL * how to flash eMMC with rkdeveloptool Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: board: lion_rk3368: update README flash instructionsKlaus Goger
Add a section to the README on how to flash the on-board eMMC with the rkdeveloptool. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: rk322x: Disable integrated macphy for saving power consumingDavid Wu
Unfortunately, the integrated macphy default is enabled, which will increase power consuming, if we do not use this PHY. So let's disable it at first, which will save power consuming. If we really use it, then enable it in driver level. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
generated by cgit (git 2.34.1) at 2025-01-02 21:54:22 +0000