summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-09-11env: ti: boot: Select dtb name for dra76Lokesh Vutla
Select dtb name for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add support for powering on mmc ldoLokesh Vutla
ldo4 is used to poweron mmc on dra76-evm. Enable it. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add the pinmux dataLokesh Vutla
Adding pinmux and IODELAY data for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add DDR dataLokesh Vutla
dra76-evm has the ddr parts connectedi running at 666MHz: EMIF1: MT41K512M16HA-125 AIT:A x 2 EMIF2: MT41K512M8RH-125-AAT:E x 4 Add support for configuring the above DDR parts. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add the pmic dataKeerthy
dra76-evm uses lp8736 and tps65917 pmic for powering on various peripherals. Add data for these pmics and register for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add epprom supportLokesh Vutla
The dra76-evm is a board based on TI's DRA76 processor Add eeprom support Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: dra76: Add support for ES1.0 detectionPraneeth Bajjuri
dra76 family is a high-performance, infotainment application device, based on OMAP architecture on a 28-nm technology. This contains most of the subsystems, peripherals that are available on dra74, dra72 family. This SoC mainly features Subsystems: - 2 x Cortex-A15 with max speed of 1.8GHz - 2 X DSP - 2 X Cortex-M4 IPU - ISS - CAL - DSS - VPE - VIP Connectivity peripherals: - 1 USB3.0 and 3 USB2.0 subsystems - 1 x SATA - 2 x PCI Express Gen2 - 3-port Gigabit ethernet switch - 2 x CAN - MCAN Adding CPU detection support for the dra76 ES1.0 soc and update prcm, control module, dplls data. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: dra7: Kconfig: Select LP87565 related configsLokesh Vutla
LP87565 is present on dra76-evm. Select it for TARGET_DRA7XX_EVM. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11palmas: Add support for powering different ldosLokesh Vutla
It is not necessary that ldo1 is used to power on mmc. So, add support for passing ldo registers for powering on mmc. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: omap5+: Add board specific ldo poweringLokesh Vutla
It is not necessary all omap5+ based uses the same PMIC to poweron mmc. So add support for enabling mmc based on board. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2017-09-11Prepare v2017.09Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-11MAINTAINERS: board: qcom: db410c: Maintainer changedJorge Ramirez-Ortiz
Replacing original author Mateusz Kulikowski <mateusz.kulikowski@gmail.com> as db410c maintainer Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-09-11ipu_common: Let the MX6 IPU clock be calculated in run-timeFabio Estevam
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de> [agust: fixed #endif in cgtqmx6eval.h] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-09-10cmd: ide: Make the first device the default oneBin Meng
At present the IDE device number is initialized to -1, which means we cannot type "ide read" command before setting the device number via "ide device #". For convenience, let's set the first device as the default one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-10block: ide: Don't bother to create BLK device if no CDROM insertedBin Meng
When there is no CDROM inserted, the block size is zero hence there is no need to create a BLK device for it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-10block: ide: Fix block read/write with driver modelBin Meng
This converts the IDE driver to driver model so that block read and write are fully functional. Fixes: b7c6baef ("x86: Convert MMC to driver model") Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-09-10blk: Use macros for block device vendor/product/rev string sizeBin Meng
So far these are using magic numbers. Replace them with macros. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08edison: Disable CONFIG_USB_HOST_ETHERTom Rini
This board does dwc3 gadget, not host, so we cannot have host support or we will fail to link. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-08env: Migrate CONFIG_ENV_AES to Kconfig and deprecateTom Rini
The underlying implementation for ENV_AES has security complications and is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226 for more details. Mark this as deprecated now and delete this in the medium term if no one comes forward to re-work the support. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-08usb: doc: update README.usb for new config optionsChris Packham
A number of the config options for USB networking have been migrated to Kconfig. Update README.usb to reflect this. Signed-off-by: Chris Packham <judge.packham@gmail.com>
2017-09-08usb: net: migrate USB Ethernet adapters to KconfigChris Packham
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08Kconfig: drop CONFIG_USB_ETHER_RNDISChris Packham
This is not a valid option. Drop it. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08Kconfig: drop CONFIG_USB_ETHER_DM9601Chris Packham
This is not a valid option. Drop it. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08README: Fix typo in description of CONFIG_OF_EMBEDNobuhiro Iwamatsu
The correct name is 'gd->fdt_blob', not 'gd->blob'. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-08rockchip: enable SPL_SYSRESET config for all Rockchip SoCsKever Yang
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET for do_reset() in SPL for Rockchip SoCs. References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro" Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-08rockchip: rk3328: fix syscon id tableKever Yang
syscon id table need a dummy member as NULL ending, or else system will panic while try to match a compatible in this table as a list. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-07ARM: rmobile: Disable CONFIG_ARCH_FIXUP_FDT_MEMORYMarek Vasut
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying the memory {} nodes in the DT passed to the Linux kernel. The R8A779x DT contains multiple memory {} nodes, while U-Boot only modifies the first one and stuffs all the memory entries into it, which is wrong. Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to fix the issue this close to the release, while the real fix is to extend the fdt_fixup_memory_banks() to handle multiple memory nodes in DT. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-07ARM: rmobile: Fix SD divider settings on Gen3Marek Vasut
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock must be divided by 4 rather than 2 because a hardware workaround present only in the H3 ES1.0 has been removed from these chips. U-Boot currently only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider to 4 to prevent SD instability. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-07Merge git://git.denx.de/u-boot-netTom Rini
2017-09-07net: fix typosHeinrich Schuchardt
%s/Desriptor/Descriptor/g Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-09-07armv8: ls1043/ls1046aqds: add support for RGMII_TXIDMadalin Bucur
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: York Sun <york.sun@nxp.com>
2017-09-07net: nfs: Drop CONFIG_NFS_READ_SIZETom Rini
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default of 1024. There are in fact no in-tree users that increase this size. Adjust the comment to reflect what could be done in the future in conjunction with CONFIG_IP_DEFRAG. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-09-07net: phy: realtek: fix enabling of the TX-delay for RTL8211FMadalin Bucur
The old logic always enabled the TX-delay when the phy-mode was set to PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and disable it for PHY_INTERFACE_MODE_RGMII. Based on a similar change made in the Linux Realtek PHY driver by Martin Blumenstingl <martin.blumenstingl@googlemail.com>. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: York Sun <york.sun@nxp.com>
2017-09-07spl: typo fix for SPL_ATF_SUPPORT descriptionKever Yang
Delete one redundant 'which' for SPL_ATF_SUPPORT description. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-09-07linker_lists: remove incorrect commentHeinrich Schuchardt
Remove a comment line refering to a non-existent file. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-09-07vsprintf: vsprintf does not have parameter sizeHeinrich Schuchardt
The inline documentation of vsprintf mentions a parameter size which does not exist in the function declaration. int vsprintf(char *buf, const char *fmt, va_list args); Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-09-07Revert "dm: arm: rpi: Drop CONFIG_OF_EMBED"Paul Barker
This reverts commit 25877d4e4c45451c5398aec3de50e0d5befe0e9f. This is a workaround for Raspberry Pi boot failures seen when passing on the device tree provided by the Raspberry Pi firmware at boot. Without CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try to boot Linux with this device tree. Signed-off-by: Paul Barker <pbarker@toganlabs.com> Cc: Simon Glass <sjg@chromium.org> Tested-by: Jonathan Gray <jsg@jsg.id.au> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-07tools: .gitignore: Add libfdt related filesBin Meng
Some files are generated during libfdt build. Ignore them. This was wrongly put in the .gitignore in the root directory before. Now let's remove entries there and put them in the right place. Fixes: 34e2c285 ("gitignore: add intermediates from libfdt build") Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-09-07tools: .gitignore: Sort in alphabetical orderBin Meng
These are currently out of alphabetical order. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-09-07doc: remove duplicate text in README.gptAlison Chaiken
Signed-off-by: Alison Chaiken <alison@she-devel.com>
2017-09-07part: mac: Suppress the error message after reading ddbBin Meng
Change to use 'debug' to output the error message if it fails to read the driver descriptor block. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-09-05env: Add 'envtools' target to 'make help'Simon Glass
The target is not currently mentioned anywhere. Add it to the help so people can find it. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-09-05env: Fix operation of 'make environ'Simon Glass
This was broken by the recent environment refactoring. Specifically: $ make environ scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop. make: *** [Makefile:1469: environ] Error 2 Fix this by updating the Makefile and adjusting the #include filesnames in two C files. Fixes: ec74f5f (Makefile: Rename 'env' target to 'environ') Reported-by: Måns Rullgård <mans@mansr.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-09-05usb: gadget: g_dnl: Sync internal SN variable with envSam Protsenko
Since commit 842778a09104 ("usb: gadget: g_dnl: only set iSerialNumber if we have a serial#") "fastboot devices" stopped to show correct device serial number for TI boards, showing this line instead: ???????????? fastboot This is because serial# env variable could be set after g_dnl gadget was initialized (e.g. by using env_set() in the board file). To fix this, let's update internal serial number variable (g_dnl_serial) when "serial#" env var is changed. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
2017-09-05env: Fix out of tree building of tools-allTom Rini
With the move of environment code from common/ to env/ a number of changes needed to be made to various make targets. We missed updating some of the files required for out of tree builds of the tools. Correct the 'environ' target to know that we need to work under tools/env/ still (not tools/environ/) and then update the wrappers in env_attr.c and env_flags.c to point to the new correct file. Reported-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-05Merge git://git.denx.de/u-boot-videoTom Rini
2017-09-05Merge git://git.denx.de/u-boot-rockchipTom Rini
generated by cgit (git 2.34.1) at 2024-12-27 10:43:38 +0000