summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-01-21watchdog: armada_37xx: Fix compliance with kernel's driverMarek Behún
The Armada 37xx watchdog driver was recently accepted for mainline kernel by watchdog subsystem maintainer, but the driver works a little different than the one in U-Boot. This patch fixes this. In the previous implementation there was a tiny period of time when the watchdog was disabled and the system was vulnerables - this was during pinging, which was done by disabling, setting, and enabling the counter. Now pinging is done without disabling the watchdog. We use 2 counters: Counter 1 is the watchdog counter - on expiry, the system is reset. Counter 0 is used to reset Counter 1 to start counting from the set timeout again. So Counter 1 is set to be reset on Counter 0 expiry event event and pinging is done by forcing an immediate expiry event on Counter 0. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Update defconfigMarek Behún
Add gpio command to defconfig - this can be used to detect whether the button is pressed or light LEDs. Add DS1307 RTC driver and the date command. Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset. Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP before network controller is initialized. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: dts: Fix Turris Mox device treeMarek Behún
DTC issues a warning because #address-cells and #size-cells properties are not set in the mdio node. Also add ethernet1 alias. Also add RTC node. Also fix USB3 regulator startup delay time. Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the speed value is not used byt the comphy driver for PCI Express, but should be 5 GHz nonetheless). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Check and configure modulesMarek Behún
Check if Mox modules are connected in supported mode, then configure the MDIO addresses of switch modules. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Change SERDES map depending on module topologyMarek Behún
When SFP module is connected directly to CPU module we want the SGMII lane speed at 1.25 Gbps. This is a temporary solution till there is a comphy driver in the kernel capable of changing SGMII speed at runtime. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21arm: mvebu: turris_mox: Cosmetic restructurizationMarek Behún
Restructure the board initialization source. Remove the module_topology environment variable since it won't be needed. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21ARM: mvebu: sync Armada-38x dts with Linux 4.20Chris Packham
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes not taken are new compatible strings for the uart and nand flash controller. The nand binding is best updated if/when the mtd/nand infrastructure is updated. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-01-21mpc83xx: Add support for -msingle-pic-baseJoakim Tjernlund
-msingle-pic-base is a new gcc(from 4.6) option for ppc and it reduces the size of my u-boot with about 4 KB. While at it, add -fno-jump-tables too to save a few more bytes. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Reviewed-by: Mario Six <mario.six@gdsys.cc> Tested-by: Mario Six <mario.six@gdsys.cc> (on MPC8308)
2019-01-19Kconfig: Migrate BOUNCE_BUFFERPhilipp Tomsich
The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
2019-01-19configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-18Merge tag 'fsl-qoriq-for-v2019.04-rc1' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Add TFA boot flow for more boards Add TFA boot defconfig for ls1088a and ls2088a. Add dts fixup for PCIe endpoint and root complex.
2019-01-18Merge branch '2019-01-18-master-imports'Tom Rini
- Bugfix for SPI environment optimization - Spelling fixes - Remove some defconfigs per various maintainers - Minor db410, bananapi r2 fixes - Bump QEMU to v3.1.0 for most platforms
2019-01-18env: sf: fix environment in SPI NORHeiko Schocher
commit 9a9d66f5eff0 ("env: add spi_flash_read_env function") breaks Environment functionality, as it reads only until 2 \0 are found, but fills the buffer with 0x0 instead 0xff which leads in an incorrect crc sum. Fix: init the read buffer with 0xff instead 0x00 Signed-off-by: Heiko Schocher <hs@denx.de>
2019-01-18arm: dts: am335x-pdu001: Sync with Linux 5.0-rc2Felix Brack
This patch synchronizes the PDU001 board DTS file with the one used by Linux 5.0-rc2. Signed-off-by: Felix Brack <fb@ltec.ch>
2019-01-18configs: Remove am335x_boneblack_defconfigFaiz Abbas
The am335x_evm_defconfig supports all am335x_boneblack variants. Remove the redundant am335x_boneblack_defconfig. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-18arm: am335x-pdu001: Remove SPI supportFelix Brack
On this board SPI is only used to configure the SoC driving the LC TFT display which is not used in U-Boot. Hence remove SPI support. Signed-off-by: Felix Brack <fb@ltec.ch>
2019-01-18cmd: mtd: fix compilation warning for help when SYS_LONGHELP=nQuentin Schulz
cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable] static char mtd_help_text[] = ^~~~~~~~~~~~~ When SYS_LONGHELP is not defined. After looking at how other commands work, we should surround the whole help text (even its declaration) with an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling _CMD_HELP[1] on the help text variable argument to U_BOOT_CMD. [1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181 Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-01-18travis: Switch QEMU to 3.1.0 versionMichal Simek
Vexpress ca15_tc2 is failing with 3.1.0 because of QEMU issue. When this patch is applied https://patchwork.kernel.org/patch/10754401/ Vexpress can be also turn to newer QEMU version. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-18travis: Setup QEMU_VERSION as variableMichal Simek
This change enables setting up specific Qemu version or sha1 for new targets which are added after (current) v3.0.0 version. This changes is preparation step for adding new Xilinx Versal Virt platform which was merge after v3.0.0. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-18travis: Break up the NXP Layerscape jobs moreTom Rini
The single job for all Layerscape 10xx platforms is close to, and sometimes exceeds the time limit for a single job configuration. Break this down into jobs for LS101x, LS104x and LS108x instead. While in here, in the name portion of these jobs, refer to them as NXP for ARM and not Freescale as they've been NXP for quite some time. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-18usb: host: Drop [e-o]hci-sunxi driversJagan Teki
Now Allwinner platform is all set to use Generic USB controller drivers, so remove the legacy sunxi drivers. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18sunxi: usb: Switch to Generic host controllersJagan Teki
Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18musb-new: sunxi: Use CLK and RESET supportJagan Teki
Now clock and reset drivers are available for respective SoC's so use clk and reset ops on musb driver. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-18reset: Add reset validJagan Teki
Add reset_valid to check whether given reset is valid or not. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18phy: sun4i-usb: Use CLK and RESET supportJagan Teki
Now clock and reset drivers are available for respective SoC's so use clk and reset ops on phy driver. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-18arm: sunxi: Enable CLK, RESETJagan Teki
CLK and DM_RESET drivers are now available for all of the Allwinner platforms, so enable them in arch/arm/Kconfig Enabling CLK will select DM_RESET by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18sunxi: A64: Update sun50i-a64-ccu.hJagan Teki
Update sun50i-a64-ccu.h from the Linux sunxi/dt64-for-4.20 tree: commit 679294497be31596e1c9c61507746d72b6b05f26 Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz> Date: Wed Sep 26 19:48:24 2018 +0000 arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay This should be a part of previous sync patch from commit 1b39a1834ed182bbd8036a5cd74a9ea111fa4691 Author: Andre Przywara <andre.przywara@arm.com> Date: Mon Oct 29 00:56:47 2018 +0000 sunxi: A64: Update .dts/.dtsi files Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-01-18clk: sunxi: Add Allwinner A80 CLK driverJagan Teki
Add initial clock driver for Allwinner A80. - Implement UART bus clocks via ccu_clk_gate table for A80, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement UART bus resets via ccu_reset table for A80, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18ARM: dts: sun8i: Update A80 dts(i) from Linux-v4.18-rc3Jagan Teki
Update all A80 devicetree dtsi and dtsi files from Linux-v4.18-rc3 with below commits. arch/arm/boot/dts/sun9i-a80*: commit 190e3138f9577885691540dca59c2f07540bde04 Merge: cafc87023b0d a7affb13b271 Author: Arnd Bergmann <arnd@arndb.de> Date: Tue Mar 27 14:58:00 2018 +0200 Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt include/dt-bindings/*/sun9i-a80-*: commit 783ab76ae553abc23f80ef7511052d055697531b Author: Chen-Yu Tsai <wens@csie.org> Date: Sat Jan 28 20:22:36 2017 +0800 clk: sunxi-ng: Add A80 Display Engine CCU Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same dts is not available in Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18clk: sunxi: Add Allwinner H6 CLK driverJagan Teki
Add initial clock driver for Allwinner H6. - Implement UART bus clocks via ccu_clk_gate table for H6, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement UART bus resets via ccu_reset table for H6, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-01-18clk: sunxi: Implement UART resetsJagan Teki
Implement UART resets for all relevant Allwinner SoC clock drivers via ccu reset table. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-01-18clk: sunxi: Implement UART clocksJagan Teki
Implement UART clocks for all Allwinner SoC clock drivers via ccu clock gate table. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-01-18clk: sunxi: Add Allwinner V3S CLK driverJagan Teki
Add initial clock driver for Allwinner V3S. - Implement USB bus and USB clocks via ccu_clk_gate table for V3S, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB bus and USB resets via ccu_reset table for V3S, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner R40 CLK driverJagan Teki
Add initial clock driver for Allwinner R40. - Implement USB bus and USB clocks via ccu_clk_gate for R40, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB bus and USB resets via ccu_reset table for R40, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner A83T CLK driverJagan Teki
Add initial clock driver for Allwinner A83T. - Implement USB bus and USB clocks via ccu_clk_gate table for A83T, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB bus and USB resets via ccu_reset table for A83T, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner A23/A33 CLK driverJagan Teki
Add initial clock driver for Allwinner A23/A33. - Implement USB bus and USB clocks via ccu_clk_gate table for A23/A33, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB bus and USB resets via ccu_reset table for A23/A33, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner A31 CLK driverJagan Teki
Add initial clock driver for Allwinner A31. - Implement USB ahb1 and USB clocks via ccu_clk_gate table for A31, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB ahb1 and USB resets via ccu_reset table for A31, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner A10s/A13 CLK driverJagan Teki
Add initial clock driver for Allwinner A10s/A13. - Implement USB ahb and USB clocks via ccu_clk_gate table for A10s/A13, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB resets via ccu_reset table for A10s/A13, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner A10/A20 CLK driverJagan Teki
Add initial clock driver for Allwinner A10/A20. - Implement USB ahb and USB clocks via ccu_clk_gate table for A10/A20, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB resets via ccu_reset table for A10/A20, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: sunxi: Add Allwinner H3/H5 CLK driverJagan Teki
Add initial clock driver for Allwinner H3/H5. - Implement USB bus and USB clocks via ccu_clk_gate table for H3/H5, so it can accessed in common clk enable and disable functions from clk_sunxi.c - Implement USB bus and USB resets via ccu_reset table for H3/H5, so it can accessed in common reset deassert and assert functions from reset-sunxi.c Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18reset: Add Allwinner RESET driverJagan Teki
Add common reset driver for all Allwinner SoC's. Since CLK and RESET share common DT compatible, it is CLK driver job is to bind the reset driver. So add CLK bind call on respective SoC driver by passing ccu map descriptor so-that reset deassert, deassert operations held based on ccu reset table defined from CLK driver. Select DM_RESET via CLK_SUNXI, this make hidden section of RESET since CLK and RESET share common DT compatible and code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18clk: Add Allwinner A64 CLK driverJagan Teki
Add initial clock driver for Allwinner A64. Implement USB clock enable and disable functions for OHCI, EHCI, OTG and USBPHY gate and clock registers via ccu clk gate table. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18board: sun50i-h5: Add Emlid Neutis N5 supportAleksandr Aleksandrov
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT module, DDR3 RAM and eMMC. - add neutis-devboard target to dtb makefile - add dtsi file for Neutis N5 needs - add config file for Neutis N5 Dev board Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> [jagan: update proper commit head] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18sunxi: board: Add i2c initialization for sun50iStefan Mavrodiev
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE. However even the controller is enabled, the mux for the pins are not set. This patch follows the existing mux method. Since the pads are different, separate check is added for each i2c. Tested with A64-SOM204 board. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-01-18configs: Remove am43xx_evm_ethboot_defconfigVignesh R
am43xx_evm_ethboot_defconfig is not being actively used and has not been moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such due EVM limitations. Therefore delete it. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-18configs: Remove unused am335x_evm defconfigsVignesh R
These defconfigs don't seem be actively used any more, and have not been moved to adapt DM or DT. Therefore delete them. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-18configs: am335x_evm: Enable DM_SPI and DM_SPI_FLASHVignesh R
Enable DM_SPI and DM_SPI_FLASH for actively used defconfigs for am335x_evm. Signed-off-by: Vignesh R <vigneshr@ti.com>
2019-01-18adding saveenv-command for bananapi r2Frank Wunderlich
bananapi r2 can be booted from sd-card and emmc saving the environment have to choose the storage from which the device has booted also the offset is set to 1MB to make sure env is written to block "user data area" between uboot and first partition https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2019-01-18mkimage: fixup CONFIG_FIT_EXTERNAL_OFFSETPatrick Wildt
The last parameter is expected to be the imagefile. Since -E is a flag having the output name before -p will make mkimage ignore the external offset option. Signed-off-by: Patrick Wildt <patrick@blueri.se>
2019-01-18lib: Kconfig: spelling fixesChris Packham
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2025-01-15 13:58:47 +0000