summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-08-22boards: ls1028a: Add support of I2C driver modelChuanhua Han
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the ls1028a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: lx2160: enable DM support for pcf2127 rtcChuanhua Han
Enable related configs on all lx2160ardb boards to support pcf2127 rtc DM feature. Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from Kconfig. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160aqds : Add pcf2127 nodeChuanhua Han
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for lx2160aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160ardb : Add the "u-boot, dm-pre-reloc" for i2c0Chuanhua Han
Lx2160ardb need to use i2c0 before relocation, so we also need to set u-boot, dm-pre-reloc to initialize node before relocation. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: Add pcf2127 node for lx2160ardbChuanhua Han
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodesChuanhua Han
In lx2160a soc, there are eight i2c controllers, this patch adds i2c nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller depends. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22gpio: do not include <asm/arch/gpio.h> on ARCH_LX2160AChuanhua Han
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch ls2160a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22drivers: i2c: mxc: Fix compiler error when using i2c dm modeChuanhua Han
I2C dm mode enablemenet causes below compilation errors: In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f': board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'? [-Wimplicit-function-declaration] i2c_early_init_f(); ^~~~~~~~~~~~~~~~ arch_early_init_r drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe': drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function 'enable_i2c_clk'; did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration] ret = enable_i2c_clk(1, bus->seq); ^~~~~~~~~~~~~~ enable_irq_wake So fix these compilation errors. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: lx2160a: Add support of I2C driver modelChuanhua Han
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the lx2160a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: ls1043aqds: Move CONFIG_FSL_QSPI to defconfigAshish Kumar
Move CONFIG_FSL_QSPI from header file to defconfigs, consequently unset imply config(CONFIG_SPI_FLASH_BAR) which is not valid for LS series. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1028a: select BOARD_LATE_INIT configYuantian Tang
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets so that late init work can be done. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22common: qixis: make the qixis compatible with new socYuantian Tang
This driver needs modification to work with new soc, like ls1028, since bitmap of RCFG is changed to RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0] 000 1 0 00 0 Also the RCW location is moved to only dutcfg0. RESV[7:4] RCWSRC[3:0] 1111 configurable Following commands are functional now qixis_reset qixis_reset sd qixis_reset qspi qixis_reset emmc Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22drivers: net: mc: Report extra memory to LinuxMeenakshi Aggarwal
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved. But MC support to work with 128MB or 256MB DDR memory also, in this case, rest of the memory is not usable. So reporting this extra memory to Linux through dtb memory fixup. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-20Merge branch '2019-08-20-master-imports'Tom Rini
- Assorted bugfixes
2019-08-20Merge branch '2019-08-20-ti-imports'Tom Rini
- More DaVinci cleanups - Other minor omap2plus cleanups
2019-08-20test/py: Add cmd_memory dependency back to test_mmc_wrMichal Simek
Based on discussion with Stephen Warren there was recommendation to list both memory and random command dependencies just in case that dependency is not properly handled by Kconfig. Fixes: a09c1f7e1c1b ("test/py: Fix MMC/SD block write test dependency") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2019-08-20easylogo: avoid buffer overrunHeinrich Schuchardt
Building easylogo with `HOST_TOOLS_ALL=y make tools` results in a build warning due to a possible buffer overrun: tools/easylogo/easylogo.c:453:4: note: ‘sprintf’ output between 7 and 262 bytes into a destination of size 256 sprintf (str, "%s, 0x%02x", app, *dataptr++); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Truncate the output to fit into the destination buffer. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-08-20jffs2: remove unused code filesUwe Kleine-König
I failed to find where these two files are used and a few test compile runs with JFFS2 enabled succeeded also without these.
2019-08-20mmc: mtk-sd: Add MT8183 SoC supportFabien Parent
Add support for the MT8183 in the MediaTek MMC driver. Signed-off-by: Fabien Parent <fparent@baylibre.com>
2019-08-20mailmap: provide usage instructionHeinrich Schuchardt
Looking at the contents of file .mailmap it seems that some editors assumed that translation is done by entering multiple lines into the file and the last one replaces the others. This is not how it works. The translation occurs according to entries in single lines as described in the git-check-mailmap man-page. Add a description of the file format. Add an entry for Alexander Graf as his old email address is not valid anymore. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-08-20README: Clarify use of BSS during SPL board_init_f()Andreas Dannenberg
The earlier commit.... commit a5a5d997b41a ("spl: Allow performing BSS init early before board_init_f()") ...introduced the ability to use BSS from SPL's board_init_f() as it may be required in certain exceptional use cases so go ahead and update the README to reflect this change. Note that as highlighted with the changes the use of the associated CONFIG option is generally not recommended. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-08-20arm: omap2: am43xx: Enable CONFIG_BLKSuniel Mahesh
With DM_MMC enabled, enable CONFIG_BLK to remove this compile warning for am43xx based targets: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== Targets were compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-08-20arm: dts: Makefile: clean *dtb_HSSuniel Mahesh
TI HS platforms generate *dtb_HS binary blobs and there is no rule for cleanup. Added entry for cleanup in clean-files target. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-08-20ARM: DRA7: Fixup DPLL clock rate fixup logic for newer kernelsSuman Anna
The commit 1b42ab3eda8a ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock frequencies based on OPP") updates the kernel device-tree blob to adjust the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks DT node. The hierarchy of this clocks DT node has changed in newer Linux kernels starting from v5.0, and this results in a failure in ft_fixup_clocks() function to update the clock rates on these newer kernels. Fix this by updating the lookup logic to look through both the newer and older DT hierarchy paths for the cm_core_aon clocks node. Signed-off-by: Suman Anna <s-anna@ti.com>
2019-08-20arm: baltos: switch to driver model for the watchdog timerYegor Yefremov
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2019-08-20davinci: omapl138-lcdk: Remove empty compiler directivesAdam Ford
There is an #ifdef with nothing inside it any longer. This patch removes this empty #ifdef Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20ARM: davinci: Remove duplicated referencesAdam Ford
The Kconfig file calls to ti/common/Kconfig twice which makes several of the menu items repeat themselves. In an effort to clean this up, this patch removes the second call which eliminates the duplicate menu items. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20ARM: da850evm: Remove dead codeAdam Ford
Now that SPL supports DM_SERIAL and the direct NOR boot supports DM_SERIAL, the check to see if DM_SERIAL is defined can go away, because all da850evm variants now support DM_SERIAL. This patch simply removes some dead precompiler defines. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20ARM: da850evm: Remove dead SPI CodeAdam Ford
With SPL now supporting DM_SPI, the need for compiler directives and hard-coded addresses is obsolete. This patch removes some dead legacy code defining the SPI base address Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20Revert "ARM: da850-evm: Enable SPI Flash and NAND Flash when booting NOR"Adam Ford
Sorry for the noise, but there appears to be a regression with older hardware. Since it broke the direct_nor boot option, it should be reverted until a better solution is available. This reverts commit 51cd1e2373274dc3167dabba628dcfc25828d36d.
2019-08-20ARM: omapl138_lcdk: Enable USBAdam Ford
The OMAPL138-lcdk has two USB controllers which are currently disabled. This patch enables them. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20configs: Rename environment variable fit_bootfile to name_fitAndrew F. Davis
Like we did with 'fit_loadaddr' to 'addr_fit', the variable 'fit_bootfile' contains a name and so should be prefixed with name_. Make this change here. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-08-20configs: Rename environment variable fit_loadaddr to addr_fitAndrew F. Davis
This is the first part of a larger effort I would like to propose to unify and simplify the default set of environment variables. When many early environment variables were named there were fewer images being loaded, usually just a kernel. At this time names like 'loadaddr' would suffice. Now we have more images and many more commands that act on them, often re-using the same variable for several different uses. The contents of a variable are also not immediately known causing one to have to look up a chain of variables to understand what a command is actually doing. I suggest the following. To start, all variables containing names should be prefixed with name_ and addresses with addr_. This is like how K2 already does things and allows for simple universal commands like: get_fdt_nfs=nfs ${addr_fdt} /boot/${name_fdt} Which is very clear on what is intended here and would work across all board that using the this naming convention. We can do this one variable at a time, start here with addr_fit. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Andreas Dannenberg <dannenberg@ti.com>
2019-08-20configs: Remove unneeded overlay_files environment variableAndrew F. Davis
The variable 'name_overlays' serves the same purpose. Remove 'overlay_files' and use 'name_overlays' everywhere. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-08-20arm: baltos: use device tree alias to access Ethernet slaveYegor Yefremov
The full path has changed in the recent kernels so that it is not possible to load them. Aliases "ethernet0" and "ethernet1" are still present in both legacy and new kernels. Also, fix error messages to correspond to the taken actions. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2019-08-19Merge tag 'u-boot-rockchip-20190819' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Add ROC-RK3399-PC board support - Move CONFIG_SPI_FLASH_GIGADEVICE and CONFIG_CMD_USB_MASS_STORAGE to Kconfig - using SYSRESET_POWER_OFF for poweroff (Note that patch for rk8xx pmic is droped for it can not pass Travis build) - fix ofnode_get_name() assert
2019-08-19Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- QEMU build warning fix when CONFIG_DISTRO_DEFAULTS=n - Small fixes on x86 reST docs - Allow CBFS to be used in SPL - Remove x86 specific GD flags
2019-08-19sysreset: move stm32mp sysreset poweroff implementation to sysreset uclassUrja Rannikko
This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF to signal when we need it. Enable it from the STPMIC1 config and in sandbox. The config flag is transitionary, that is it can be removed after all poweroff implementations use sysreset, and just have CMD_POWEROFF depend on sysreset. Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-19sysreset: switch to using SYSRESET_POWER_OFF for poweroffUrja Rannikko
It seems that SYSRESET_POWER_OFF was added recently, and all previous code used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a PMIC-level power cycle, not a poweroff. (Comment by Simon Glass) SYSRESET_POWER means to do a power reset (removing and reinstating all power) SYSRESET_POWER_OFF means to turn the device off and leave it off Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> (Update comment to help understand the patch) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-19configs: update rk3288 veyron defconfigsUrja Rannikko
Updates jerry, mickey, minnie and speedy defconfigs to: - fit the SPL in 32k - boot from SPI (only) - remove gadget support (these have no OTG port) Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (Rebase on top of tree) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-19configs: Move CONFIG_CMD_USB_MASS_STORAGE properly into KconfigUrja Rannikko
This affects RK3036, RK322X and RK3288 - the defconfig changes done by moveconfig.py for the veyrons were left out on purpose because they dont have an OTG port, and will get their config updated in the next commit. Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-19configs: Move CONFIG_SPI_FLASH_GIGADEVICE properly into KconfigUrja Rannikko
Affects rk3288 veyrons and rk3036, this was mostly done by moveconfig.py. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-19core: ofnode: do not assert if node not valid in ofnode_get_name()Kever Yang
In some case with LIVE DT, some node always not valid, or not have a valid name, eg. blk driver add by mmc. Return fail instead of Assert for this kind of ofnode, and this help with assert happen from time to time when of_live is enabled and DEBUG is enabled. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-08-19rockchip: rk3399: Add ROC-RK3399-PC supportLevin Du
Add initial support for ROC-RK3399-PC board. Specification - Rockchip RK3399 - LPDDR4 4GiB - eMMC slot - SD card slot - RTL8211E 1Gbps - HDMI Out, DP, MIPI DSI/CSI, EDP - PCIe M.2 - USB 2.0, USB-3.0 - USB C Type Commit details of rk3399-roc-pc.dts sync from Linux v5.2: "arm64: dts: rockchip: add support for ROC-RK3399-PC board" (sha1: 8bb878cf20ae10809c36db96993bfce7026d062b) Signed-off-by: Levin Du <djw@t-chip.com.cn> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-18global_data: Remove comment of reserved arch-specific GD flagsStefan Roese
With the removal of the x86 specific GD flags, there are no arch- specific GD flags any more. Let's remove the comment about reserving the upper 16 bits for arch-specific flags in the common header. This gives us more flexibility with the usage of the GD flags. As a matter of fact, we are already using more than 16 bits for common GD flags (with the addition of GD_FLG_WDT_READY). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-08-18x86: Remove x86 specific GD flags as they are not referenced at allStefan Roese
This patch removes the x86 architecture specific GD flags (GD_FLG_COLD_BOOT & GD_FLG_WARM_BOOT), as they are not used. Only GD_FLG_COLD_BOOT is referenced in coreboot.c but assigned in start16.S. But the coreboot target does not use start16.S at all and boots directly from the 32-bit start code. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-08-18cbfs: Rename camel-case variablesSimon Glass
Rename some camel-case variables to match U-Boot style. Camel case is not generally allowed in U-Boot. Rename this variable to fit in with the style. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-18cbfs: Add functions to support multiple CBFSsSimon Glass
Sometimes an image has multiple CBFS. The current CBFS API is limited to handling only one at time. Also it keeps track of the CBFS internally in BSS, which does not work before relocation, for example. Add a few new functions to overcome these limitations. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-18cbfs: Move result variable into the structSimon Glass
Move the result variable into the struct also, so that it can be used when BSS is not available. Add a function to read it. Note that all functions sill use the BSS version of the data. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-18cbfs: Move static variables into a structSimon Glass
At present there are a number of static variables in BSS. This cannot work with SPL, at least until BSS is available in board_init_r(). Move the variables into a struct, so it is possible to malloc() it and use it before BSS is available. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>