summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-06-12board: tbs2910: Enable distro_boot support.Denis 'GNUtoo' Carikli
This keeps the compatibility with the old bootcmd. The fdtfile environment variable also needed to be set to imx6q-tbs2910.dtb to enable booting mainline kernels otherwise with extlinux.conf it tries to load mx6-tbs2910.dtb instead. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution, we have the following size differences: - text: +2041 bytes - data: 0 bytes - bss: 0 bytes - total: +2041 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910_defconfig: Add support for booting general purpose distributionsDenis 'GNUtoo' Carikli
This is needed to enable distro_boot support later on. Adding the necessary configuration to enable booting general purpose distributions is typically done by enabling CONFIG_DISTRO_DEFAULTS. However the resulting image size is is already very close to the size limit and PXE isn't strictly needed, so instead we made sure that all the configuration selected by CONFIG_DISTRO_DEFAULTS were selected, with the exception of PXE related configuration (CONFIG_BOOTP_PXE and CONFIG_CMD_PXE) that are both disabled. With arm-linux-gnueabi-gcc 9.3.0-1 from the Parabola GNU/Linux distribution, we have the following size differences: - text: +7526 bytes - data: +28 bytes - bss: -12 bytes - total: +7542 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: move CONFIG_BOOTCOMMAND from header to defconfigDenis 'GNUtoo' Carikli
This doesn't affect the size of the image: with arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution, the text, data, bss and total sizes remain unchanged. Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: disable CONFIG_GZIPDenis 'GNUtoo' Carikli
As that the resulting image is already very close to the size limit, and that CONFIG_GZIP is not strictly required, removing it shouldn't hurt. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution we have the following size reduction: - text: 9752 - data: 0 - bss: 16 - total: 9768 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Acked-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: disable loadb and loads commandsDenis 'GNUtoo' Carikli
The loadb and loads commands are not needed for booting. There are also more reliable and faster alternatives to loadb and loads that can be used with the current configuration. As that the resulting image is already very close to the size limit, removing the loadb and loads commands shouldn't hurt. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution we have the following size reduction: - text: 6733 bytes - data: 116 bytes - bss: 1172 bytes - total: 8021 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Acked-by: Soeren Moch <smoch@web.de>
2020-06-12Add support for SHA384 and SHA512Reuben Dowle
The current recommendation for best security practice from the US government is to use SHA384 for TOP SECRET [1]. This patch adds support for SHA384 and SHA512 in the hash command, and also allows FIT images to be hashed with these algorithms, and signed with sha384,rsaXXXX and sha512,rsaXXXX The SHA implementation is adapted from the linux kernel implementation. [1] Commercial National Security Algorithm Suite http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
2020-06-11configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-08Prepare v2020.07-rc4Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-08cmd: Correct the 'md.q' commandSimon Glass
This displays incorrect data at present due to a missing header file in display_options. Fix it. Fixes: 09140113108 ("command: Remove the cmd_tbl_t typedef") Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xxTom Rini
- DM_ETH support for P2041RDB, T1024RDB, P5040DS, P3041DS, P4080DS, bug fixes - Add TBI PHY access through MII - DDR: Rework errata workaround for A008109, A008378, 009942
2020-06-08Merge tag 'u-boot-rockchip-20200607' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - revive rk3399 puma board to adapt mainline dts; - Fix rk3399-evb stdout path; - Enable PCIe for rk3399: Rockpro64, firefly, pinebookpro; - Add rk3328 Rock-pi-e board; - Enable SPI boot for rockpro64 and roc-pc-rk3399;
2020-06-07rockchip: enable PCIe and NVMe on Pinebook ProPatrick Wildt
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Pinebook Pro. Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: enable new usb config optionsHeiko Stuebner
With recently added changes we get support for usb3 including handling of the phys (type-c and inno-usb2), so enable the necessary config options on puma. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: drop special handling of usb host regulatorHeiko Stuebner
With the current usb stack in u-boot, all host ports on puma work flawlessly without any additional special handling, so drop that usb hub hacking from the puma board. Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07rockchip: puma: remove separate fit generatorHeiko Stuebner
The introduction of the puma-specific generator was mainly a way to split the pmu firmware from the ATF binary and not having to distribute that 4GB (sparse) image that was created before moving to the bl31.elf as base. Looking at the publically available repository for that separate pmu firmware https://git.theobroma-systems.com/rk3399-cortex-m0.git/ there is also no activity for 3 years and apart from some build customizations no other changes were done. And even then, if changes need to be made, this can very well also happen in the atf context itself, so there is no real need to diverge from the established build procedure and we can just go back to using the main make_fit_atf.py script. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: reorganize devicetrees to actually work and match upstreamHeiko Stuebner
So far the puma dts files only just included the main puma dtsi without handling the actual baseboard and rk3399-puma.dtsi was very much detached from the variant in the mainline Linux kernel. Recent changes resulted in a strange situation with nonworking puma boards. Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi") moved the sdram include from rk3399-puma-ddrX.dts to new files rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though. Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") replaced the rk3399-puma.dtsi nearly completely, but in the kernel it definitly depends on a baseboard dts to actually enable peripherals like sd-slot, uarts, etc. So to untagle this and bring the whole thing more in line with mainline Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate DDR-option devicetrees and instead replace them with a puma Kconfig option to select and include the needed DDR variant. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation of misc_init_rHeiko Stuebner
The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces as indentation, so correct that by moving to the required tabs. Fixes: fa177ff0208b ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr") Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation for -u-boot.dtsiHeiko Stuebner
Tabs not spaces, so transform it to the common styling. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulatorHeiko Stuebner
The regulator enable-gpio uses opposite values for the declaration vs. the enable_active_low property, breaking the regulator enablement. Make the usbhost-supply work again by bringing them in sync again. This mimics the upstream Linux change found on: http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for gmac reset pinHeiko Stuebner
The gmac reset has opposite values for the gpio declaration and the separate reset-active, bring this in line to make u-boot also find the ethernet-phy. This mimics the upstream Linux commit found on https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: add SPI bootMarcin Juszkiewicz
U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) Trying to boot from SPI U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: vidconsole Err: vidconsole Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 => Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07doc: rockchip: Document SPI flash program stepsJagan Teki
Document SPI flash program steps for rockchip platforms. Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Add SPI bootJagan Teki
U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1 NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020 U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07Makefile: Drop to handle rkspi image typeJagan Teki
On rockchip platforms, SPI boot image creation is not straightforward like MMC boot image creation where former requires to specify tpl, spl in multimage format in mkimage, and later simply do a concatenate mkimaged-tpl with spl. On this note, let drop rkspi image type creation via kbuild and let inform via rockchip.rst Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3399-evb: add stdout-path for the boardKever Yang
The 'stdout-path' is missing after dts sync. Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3328: add rock-pi-e-rk3328_defconfig fileb.l.huang
This commit add the default configuration file and relevant description for rock-pi-e board Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: rk3328: add rock-pi-e dts fileb.l.huang
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328 Quad-Core ARM Cortex A53. Net - Dual ethernet port, 1 X Gbe, 1 X 100M USB - USB 3.0 DC - USB-Type C, 5V 2A Storage - TF card, eMMC Just build idbloader.img and u-boot.itb for Rockpi E board and follow the blow steps to replace the relevant partition. dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: Enable PCIe and NVMe on ROCKPro64Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the ROCKPro64 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Firefly RK3399 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-06Merge tag 'efi-2020-07-rc4-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc4 (2) The following problems are resolved: * When booting via UEFI an SMBIOS table is presented to the operating system. If U-Boot tries to add an empty string, this results in corrupted SMBIOS information. We will now use "Unknown" as property value. * The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver the missing DM_RNG Kconfig dependency is added. * Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are added.
2020-06-05efi_loader: comments EFI_SIMPLE_TEXT_OUTPUT_PROTOCOLHeinrich Schuchardt
Provide missing comments for the functions implementing the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-05virtio: VIRTIO_RNG depends on DM_RNGHeinrich Schuchardt
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-05smbios: empty strings in smbios_add_string()Heinrich Schuchardt
smbios_add_string() cannot deal with empty strings. This leads to incorrect property values and invalid tables. E.g. for the pine64-lts_defconfig CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows: Table 1: Manufacturer: sunxi Product Name: sunxi Table 3: Invalid entry length (2). DMI table is broken! Stop. Replace empty strings by "Unknown". Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Merge branch '2020-06-04-misc-bugfixes'Tom Rini
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific checks in a localized area, so they aren't lost in the future. - Complete / re-migrate some options from config headers to defconfigs - Add dependencies to the various debug uart drivers
2020-06-04checkpatch.pl: Add check for defining CONFIG_CMD_xxx via config filesTom Rini
All of our cmds have a Kconfig entry. Making enabling a CMD via the config file an error to checkpatch.pl. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04checkpatch.pl: Request if() instead #ifdefSimon Glass
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this, suggest using the compile-time construct. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Request a test when a new command is addedSimon Glass
This request is made with nearly every new command. Point to some docs on how to do it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Warn if the flattree API is usedSimon Glass
We want people to use the livetree API, so request it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Add a check for tests needed for uclassesSimon Glass
A common problem when submitting a new uclass is to forget to add sandbox tests. Add a warning for this. Of course tests should always be added for new code, but this one seems to be missed by nearly every new contributor. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Add a U-Boot optionSimon Glass
Add an option to indicate that U-Boot-specific checks should be enabled. Add a function to house the code that will be added. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Update to v5.7Simon Glass
Keep the U-Boot changes to $logFunctions Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Resync with v5.7 release which changed the default max line length, update commit to reflect] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-01-09 04:37:59 +0000