summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-12-16powerpc/nand spl: link libgccScott Wood
Recent GCC (4.4+) performs out-of-line epilogues in some cases, when optimizing for size. It causes a link error for _restgpr_30_x (and similar) if libgcc is not linked. It actually increases size with very small binaries, due to the fixed size of the out-of-line code, and not having any functions that actually need to restore more than 2 or 3 registers. But I don't see a way to turn it off, other than asking GCC to optimize for speed -- which may also increase size for some boards. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Wolfgang Denk <wd@denx.de>
2010-12-16MAINTAINERS: Transfer openrd_base maintainership to Prafulla WadaskarSimon Kagstrom
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
2010-12-16Armada100: Add Board Support for Marvell Aspenite-DBPrafulla Wadaskar
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with * Processor upto 1.2GHz * Parallel 1Gb x8 DDR2-1066 MHz * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR * Footprints for eMMC/eSD NAND & MMC x8 card * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket * SEAF memory board, subset of PISMO2 With Peripherals: * 4.3” WVGA 24-bit LCD * Audio codecs (AC97 & I2S), TSI * VGA camera * Video in via 3 RCA jacks, and HDMI type C out * Marvell 88W8688 802.11bg/BT module * GPS RF IC * Dual analog mics & speakers, headset jack, LED, ambient light sensor * USB2.0 HS host (A), OTG (micro AB) * FE PHY, PCIE Mini Card slot * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR This patch adds basic board support with DRAM and UART functionality The patch is tested for boot from DRAM using XDB Signed-off-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16mv-common.h: Add support for ARMADA100 PlatformsPrafulla Wadaskar
This patch adds commonly used macros for ARMADA100 based baords, Also some code reshuffled and updated for typos and comments Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16Serial: Add UART support for Marvell ARMADA 100 SoCs.Prafulla Wadaskar
ARMADA 100 SoCs has NS16550 compatible UART peripheral This patch enables the same for ARMADA100 platforms Signed-off-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16Serial: ns16550: Add support for CONFIG_SYS_NS16550_IER macroPrafulla Wadaskar
On some processors this ier register configuration is different for ex. Marvell Armada100 This patch introduce CONFIG_SYS_NS16550_IER macro support to unconditionally initialize this register. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16add Multi Function Pin configuration support for ARMADA100Prafulla Wadaskar
This patch adds the support MFP support for Marvell ARMADA100 SoCs Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16gpio: Add Multi-Function-Pin configuration driver for Marvell SoCsPrafulla Wadaskar
Most of the Marvell SoCs has Multi Function Pin (MFP) configuration registers For ex. ARMADA100. These registers are programmed to expose the specific functionality associated with respective SoC Pins This driver provides configuration APIs, using them, configuration need to be done in board specific code for ex- following code configures MFPs 107 and 108 for UART_TX/RX functionality int board_early_init_f(void) { u32 mfp_cfg[] = { /* Console on UART1 */ MFP107_UART1_RXD, MFP108_UART1_TXD, MFP_EOC /*End of configureation*/ }; /* configure MFP's */ mfp_config(mfp_cfg); return 0; } Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16arm: Add Support for Marvell ARMADA 100 Familiy SoCsPrafulla Wadaskar
ARMADA 100 Family processors are highly integrated SoCs based on Sheeva_88SV331x-v5 PJ1 cpu core. Ref: http://www.marvell.com/products/processors/applications/armada_100 SoC versions Supported: 1) ARMADA168/88AP168 (Aspen P) 2) ARMADA166/88AP166 (Aspen M) 3) ARMADA162/88AP162 (Aspen L) Contributors: Eric Miao <eric.y.miao@gmail.com> Lei Wen <leiwen@marvell.com> Mahavir Jain <mjain@marvell.com> Signed-off-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16Merge branch 'master' of ../master into nextWolfgang Denk
2010-12-16mpc52xx: add support for tqm52xx based board charonHeiko Schocher
- serial console in PSC1 - 128MiB DRAM - 32MiB Flash - FEC Ethernet - 2 I2C busses - FPGA on CS3 - IDE - VGA SMI501 Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-16Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-12-16pm9261: enable cache commandAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16pm9261: ARM relocation supportAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16pm9263: enable cache commandAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16pm9263: ARM relocation supportAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16pm9g45: enable cache commandAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16pm9g45: ARM relocation supportAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-15ppc4xx: Fix missing linker scripts for partial linkingStefan Roese
This patch fixes the acadia_nand and kilauea_nand linker scripts which have been missing in commit ee8028b7 [ppc4xx: Cleanup for partial linking and --gc-sections] Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bernhard Weirich <Bernhard.Weirich@riedel.net>
2010-12-14Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2010-12-14Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-12-13ARM: */start.S: use canonical asm syntaxWolfgang Denk
Make code build with older tool chains. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-13mpc83xx: fix pcie enumerationBaidu Boy
This patch fix a problem for the pcie enumeration for mpc83xx cpus. Without this we will not get correct value in hose->regions[...]. The pointer *reg in function mpc83xx_pcie_init_bus() shall not be changed. Because we will use this pointer as a parameter to call function mpc83xx_pcie_register_hose(). Signed-off-by: Baidu Boy <liucai.lfn@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-12-13p1022ds: fix switching of DIU/LBC signalsTimur Tabi
On the P1022, the pins which drive the video display (DIU) are muxed with the local bus controller (LBC), so if the DIU is active, the pins need to be temporarily muxed to LBC whenever accessing NOR flash. The code which handled this transition is checking and changing the wrong bits in PMUXCR. Also add a follow-up read after a write to NOR flash if we're going to mux back to DIU after the write, as described in the P1022 RM. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13fsl_esdhc: Set the eSHDC DMACTL[SNOOP] bit after resetting the controllerP.V.Suresh
eSDHC host controller reset results in clearing of snoop bit also. This patch sets the SNOOP bit after the completion of host controller reset. Without this patch mmc reads are not consistent. Signed-off-by: P.V.Suresh <pala@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13fsl_upm: Add MxMR/MDR synchronizationJohn Schmoller
According to Freescale reference manuals (eg section "13.4.4.2 Programming the UPMs" of the P4080 Reference Manual): "Since the result of any update to the MxMR/MDR register must be in effect before the dummy read or write to the UPM region, a write to MxMR/MDR should be followed immediately by a read of MxMR/MDR." The UPM on a custom P4080-based board did not work without performing a read of MxMR/MDR after a write. Signed-off-by: John Schmoller <jschmoller@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13tsec: Revert to setting TBICR_ANEG_ENABLE by default for SGMIIKumar Gala
The following commit: commit 46e91674fb4b6d06c6a4984c0b5ac7d9a16923f4 Author: Peter Tyser <ptyser@xes-inc.com> Date: Tue Nov 3 17:52:07 2009 -0600 tsec: Force TBI PHY to 1000Mbps full duplex in SGMII mode Removed setting Auto-Neg by default, however this is believed to be proper default configuration for initialization of the TBI interface. Instead we explicitly set CONFIG_TSEC_TBICR_SETTINGS for the XPedite5370 & XPedite5500 boards that use a Broadcomm PHY which require Auto-Neg to be disabled to function properly. This addresses a breakage on the P2020 DS & MPC8572 DS boards when used with an SGMII riser card. We also remove setting CONFIG_TSEC_TBICR_SETTINGS on the P1_P2_RDB family of boards as now the default setting is sufficient for them. Additionally, we clean up the code a bit to remove an unnecessary second define. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Peter Tyser <ptyser@xes-inc.com>
2010-12-11omap3: emif|sdrc: use a single global data defineNishanth Menon
DECLARE_GLOBAL_DATA_PTR declarations in functions are inherently troublesome with various compilers (e.g. gcc 4.5) Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11OMAP3: SPI driverDirk Behme
CC: Ruslan N. Araslanov <byaaka@yandex.ru> Signed-off-by: Ruslan Araslanov <ruslan.araslanov@vitecmm.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11ARMV7: OMAP4: twl6030 add battery charging supportBalaji T K
Add battery charging support twl6030 driver. Add support for battery voltage and current measurements. Add command to get battery status and start/stop battery charging from USB. Signed-off-by: Balaji T K <balajitk@ti.com> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11OMAP: Timer: Replace bss variable by gdDirk Behme
Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc bss values in the OMAP timer driver. The usage of bss values in drivers before initialisation of bss is forbidden. In that special case some data in .rel.dyn gets corrupted. Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Tested-by: John Rigby <john.rigby@linaro.org> Tested-by: Nishanth Menon <nm@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11DaVinci DM6446: Config UpdateSandeep Paulraj
The DM6446 does not build due to the ARM relocation patch. Also the board does not build in the NOR mode. Changed default to NAND to ensure no build failure. While at it removed CONFIG_CMD_KGDB Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11davinci: Rewrite timer.c to use tbl/tbu emulation variables in gdNick Thompson
This change allows the davinci timer functions to be used before relocation since it avoids using static variables prior to BSS being made available. The code is based on that used in the at91 timers, modified to use a davinci specific hardware timer. It also maintains reset_timer() to allow deprecated timer usage to continue to work (for example, in nand_base.c) Signed-off-by: Nick Thompson <nick.thompson@ge.com> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Tested-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11Merge branch 'next' of git://git.denx.de/u-boot into nextSandeep Paulraj
2010-12-09Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk
2010-12-09include/linux/mii.h: update for supporting GEMacpaul Lin
This file has been synced (copy) from Linux source code. This commit was based on kernel 2.6.32. It updates gigabit related phy registers and basic definitions. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2010-12-09ARM: make timer variables in gt_t available for all ARM platformsPrafulla Wadaskar
All code that attemots to access variables in BSS before relocation (for example directly or indirectly by board_init_f()) needs to be fixed. Especially timer.c needs to fix on most of the ARM platforms. This patch makes timer related variables in gd_t available for all ARM implementations. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Edited commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-09armv7: fix relocation skipAndreas Bießmann
I doubt the stack_setup() was defective before: we load the current location of _start and compare against destination of relocate_code(). If we are already there we shoud skip the relocation and jump over to clear_bss. Before the clear_bss was also skipped. Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
2010-12-09arm: fixloop(): do not use r8 for relocationAndreas Bießmann
r8 is used for global_data and should therefore be left alone! For C code the compiler flag --fixed-r8 does the job, but in assembler we need to be aware of that fact. Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
2010-12-09arm: relocate_code(): do not set register uselessAndreas Bießmann
In case we are still at relocation target address before relocation we do not need to load the registers needed for relocation. We should instead skip the whole relocation part and jump over to clear_bss immediately. Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
2010-12-09arm: copy_loop(): use scratch registerAndreas Bießmann
This patch uses r1 as scratch register for copy_loop(). Therefore we do not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the destination address of relocation). Therefore r7 can be used later on for other purposes. Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
2010-12-09hwconfig: Fix handling of env_hwconfig, board_hwconfig, and cpu_hwconfigKumar Gala
The handling of env_hwconfig, board_hwconfig, and cpu_hwconfig got broken when we removed the boards defining dummy board_hwconfig & cpu_hwconfig values. We fix this by handling the various strings in priority order. If hwconfig_parse returns NULL for a given string we check the next one in order (env_hwconfig, board_hwconfig, followed by cpu_hwconfig). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-09Move LDSCRIPT definitions to board config files.Wolfgang Denk
Recent cleanup actions resulted in a number of config.mk files that contained only LDSCRIPT definitions. Move these into th respective board config files and remove the now empty config.mk files. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Detlev Zundel <dzu@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Detlev Zundel < dzu@denx.de> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Heiko Schocher<hs@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-12-09Remove redundant config.mk filesWolfgang Denk
Recent cleanup actions resulted in a number of config.mk files that contained only redundant entries like PLATFORM_CPPFLAGS += -I$(TOPDIR) or settings of variables that were not used anywhere in the code, like TEXT_END = 0xfe080000 Remove these unnecessary files. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Scott McNutt <smcnutt@psyent.com> Cc: Wolfgang Wegner <w.wegner@astro-kom.de> Cc: Josef Wagner <Wagner@Microsys.de> Cc: Tolunay Orkun <torkun@nextio.com> Cc: Frank Panno <fpanno@delphintech.com> Cc: Heiko Schocher <hs@denx.de> Cc: Brad Kemp <Brad.Kemp@seranoa.com> Acked-by: Heiko Schocher<hs@denx.de>
2010-12-09Davinci: add support for the ea20 boardStefano Babic
This board uses the OMAP-L138 SOM stacked on a custom baseboard. It supports SPI Flash, Ethernet with RMII. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09Davinci 8xx: Move common functions to share codeStefano Babic
As more Davinci 8xx board can be added, move common code to be shared between boards. * rebased ontop of Sugosh's patches * moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to arch/arm/include/asm/arch-davinci/davinci_misc.h from to arch/arm/include/asm/arch-davinci/da8xx_common.h * don't define dram functions in PRELOADER * move sync_env_enetaddr into existing EMAC ifdef * use misc.c in hawkboard nand_spl Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09da850: Add RMII support for EMACSudhakar Rajashekhara
This patch is a port of the work by Sudhakar Rajeshekhara in commit ab3effbcad8851cc65dc5241a01c064d2030a3b2 of git://arago-project.org/git/people/sandeep/u-boot-davinci.git. The da850 UI board has on it an RMII PHY which can be used if the MDC line to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by configuring the values of some GPIO pins on the IO expander of the UI board. This patch implements disabling that line via GPIO2[6], configuring the UI board's IO expander and setting only the pinmux settings that are needed for RMII operation. Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09Add board support for hawkboardSughosh Ganu
The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09Remove board_init_f function from nand_boot.cSughosh Ganu
Remove the board_init_f function from nand_spl/nand_boot.c. This function is to be defined by all boards using the nand_spl functionality in their individual board directory. Currently this function was being used by the smdk6400 board. Added the board specific function definition. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09Move and rename common headers from underSughosh Ganu
board/davinci. Move the davinci common headers to the architecture specific include file path. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit (git 2.34.1) at 2024-12-28 23:55:54 +0000