summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-12-01arm: atmel: add ddr2 initialization functionBo Shen
The MPDDRC supports different type of SDRAM This patch add ddr2 initialization function Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01arm: atmel: sama5d3: early enable PIO peripheralsBo Shen
Enable the PIO peripherals early than other peripherals. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01arm: atmel: sama5d3: the offset of MULA is 18Bo Shen
The offset of MULA field in PLLA register in sama5d3 is 18, and the length only 7 bits. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01arm: atmel: sama5d3: correct the error define of DIVBo Shen
Correct the error define of DIV. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01arm: at91: pm9261: remove undefined bit in mckrBo Shen
The PLLADIV2 bit is not defined in at91sam9261 SoC, so remove it. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-12-01arm: atmel: sama5d3: correct the ID for DBGU and PITBo Shen
As the DBGU and PIT has its own ID on sama5d3 SoC, while not share with SYS ID. So, correct them. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13ARM: at91: sama5d3: add support for sama5d36 chipWu, Josh
The SAMA5D36 chip is the superset product of SAMA5D3x family. For detail information please refer to: http://www.atmel.com/Microsite/sama5d3/default.aspx Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13at91: remove all occourances of CONFIG_AT91_LEGACYAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13net: remove unused CONFIG_AT91_LEGACYAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13snapper9260: remove unused AT91_LEGACYAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13at91sam9m10g45ek: remove unused CONFIG_AT91_LEGACYAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Bo Shen <voice.shen@atmel.com>
2013-11-13i2c: switch from AT91 legacy to ATMEL legacyAndreas Bießmann
Since the required API is gpio which is enclosed with CONFIG_ATMEL_LEGACY use that switch here. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Heiko Schocher <hs@denx.de>
2013-11-13video: remove AT91 legacy API from bus_vcxkAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2013-11-12arm, am335x: update for the siemens boardsSamuel Egli
- dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-12usb, g_dnl: make bcdDevice value configurableHeiko Schocher
add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
2013-11-11omap730p2: Remove boardTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11am33xx: Make SoC bootcount driver have its own symbolTom Rini
Some am33xx boards may not use the RTC block for bootcount (as it may not be wired up for the board) and use some other facility. So add another symbol for the bootcount driver for the IP block. Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11cm-t35: use gpio_led driver for status ledIgor Grinberg
Switch to using the generic gpio_led driver instead of the private to cm_t35 board led implementation. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-11am335x_evm: Fix CONS_INDEX numberingAndrew Bradford
Commit f6d1f6e4a58edae4776937647381a43fea5e83a5 broke selection of UARTs other than UART0 for am335x_evm configurations by setting CONS_INDEX to 1 for all configurations. Revert the CONS_INDEX changes. Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2013-11-11boards.cfg: update email address for ti814x_evm maintainerMatt Porter
Update my email address as ti814x_evm maintainer to save people some frustrating bounces and non-response. Signed-off-by: Matt Porter <matt.porter@linaro.org>
2013-11-11arm, am33x: make RTC32K OSC enable configurableHeiko Schocher
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-11-11bootcount: store bootcount var in environmentHeiko Schocher
If no softreset save registers are found on the hardware "bootcount" is stored in the environment. To prevent a saveenv on all reboots, the environment variable "upgrade_available" is introduced. If "upgrade_available" is 0, "bootcount" is always 0 therefore no need to save the environment on u-boot boot, if "upgrade_available" is 1 "bootcount" is incremented in the environment and environment gets written on u-boot start. So the Userspace Applikation must set the "upgrade_available" and "bootcount" variable to 0 (for example with fw_setenv), if a boot was successfully. Signed-off-by: Heiko Schocher <hs@denx.de>
2013-11-09Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
2013-11-08Merge branch 'master' of git://www.denx.de/git/u-boot-usbTom Rini
2013-11-08sandbox: convert to common time functionsRob Herring
Convert sandbox to use common time functions. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08time: add weak annotation to timer_read_counter declarationRob Herring
A weak annotation is needed in order to prevent link errors when get_ticks is overridden. This fixes sandbox build. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08netconsole loses 2nd character of inputSuriyan Ramasami
Netconsole loses the second character when used as input by either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX Before a nc_send_packet() to echo the input, a check is done to see if nc_ether is valid. If its not, it waits for an arp request and then sends the packet (which contains the first character of line to be displayed as output). As part of reaping the arp request, the second character is consumed. We protect this by making the call to NetLoop(NETCONS) between input_recursion. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-11-08serial: s5p: Staticize local functionsAxel Lin
Staticize local functions in s5p serial driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-11-08env: fix the env export varnamePierre Aubert
The env export command doesn't export the first variable of the list since commit 5a31ea04c9ee5544fbb70ad7597ea4b294840eab "env grep" - reimplement command using hexport_r() Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
2013-11-08highbank: set AUTOBOOT_KEYED_CTRLC config optionMark Langsdorf
Let highbank users break into the autoboot script with ctrl-c. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08autoboot: add an option to override keyed autobootMark Langsdorf
As originally implemented, setting the AUTOBOOT_KEYED config option will prevent users from breaking into the autoboot script with ctrl-c. Restore that option with a new config symbol. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08serial: xuartlite: Staticize local functionsAxel Lin
Staticize local functions in xuartlite driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stefan Roese <sr@denx.de> Tested-by: Michal Simek <monstr@monstr.eu>
2013-11-08serial: mxs_auart: Staticize local functionsAxel Lin
Staticize local functions in mxs_auart driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marek Vasut <marex@denx.de>
2013-11-08fs:fat: fix set file name functionPiotr Wilczek
Curently memcpy copies string without null terminating char because function strlen returns only number of characters excluding null terminating character. Replace memcpy with strcpy. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Tom Rini <trini@ti.com>
2013-11-08cmd_zfs: normalize 'file not found' errorsLuka Perkov
Signed-off-by: Luka Perkov <luka@openwrt.org>
2013-11-08cmd_reiser: normalize 'file not found' errorsLuka Perkov
Signed-off-by: Luka Perkov <luka@openwrt.org>
2013-11-08cmd_ubifs: normalize 'file not found' errorsTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2013-11-08include: delete include/linux/config.hMasahiro Yamada
Linux Kernel abolished include/linux/config.h long time ago. (around version v2.6.18..v2.6.19) We don't need to provide Linux copatibility any more. This commit deletes include/linux/config.h and fixes source files not to include this. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08config/sandbox: Add EFI and GPT supportEgbert Eich
Signed-off-by: Egbert Eich <eich@suse.com>
2013-11-08config: Define HAVE_BLOCK_DEVICE when CONFIG_CMD_GPT is setEgbert Eich
Signed-off-by: Egbert Eich <eich@suse.com>
2013-11-08cmd/gpt: Support gpt command for all devicesEgbert Eich
The gpt command was only implemented for mmc devices. There is no reason why this command should not be generalized and be applied all other storage device classes. This change both simplifies the implementation and eliminates a build failure for systems that don't support mmcs. Signed-off-by: Egbert Eich <eich@suse.com> Tested-by: Piotr Wilczek <p.wilczek@samsung.com> [trini: Change coding style slightly] Signed-off-by: Tom Rini <trini@ti.com>
2013-11-08cosmetic: UDM-net: clean up the remainders of dead driverMasahiro Yamada
This commit omits non-existing drivers/net/netarm_eth.c from the list. This driver is deleted by commit b411eb30f. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08cosmetic: UDM-serial: clean up the remainders of dead driverMasahiro Yamada
The following serial drivers do not exist any more. - ns9750_serial.c: deleted by commit 4cfc611b4 - s3c4510b_uart.c: deleted by commit afad40299 - serial_clps7111.c: deleted by commit f2e080156 - serial_netarm.c: deleted by commit b411eb30f This commit cleans up UDM-serial.txt. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08cosmetic: doc: driver-model: Do not number driver listsMasahiro Yamada
Everytime a dead driver is removed from the list, we must re-number. This is a painful task. Try git show e53232250 -- doc/driver-model/UDM-serial.txt git show 6f62f4207 -- doc/driver-model/UDM-serial.txt git show b9f4bc34a -- doc/driver-model/UDM-serial.txt to see what I mean. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08usb: dfu: make nand upload workingBo Shen
Nowhere pass a value to len, which always 0, make no transfer which cause uploading failed. This patch make nand upload working. However it needs enough malloc buffer to store read data, that means the buffer at least equal to the upload partition size, or else it doesn't work. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-11-08usb, g_dnl: make iSerialNumber board configurableHeiko Schocher
add the possibility to set the iSerialNumber board specific. Default value for iSerialNumber is 0x0. This value can changed board specific through the new function g_dnl_set_serialnumber() which must be called from the board specific function g_dnl_bind_fixup(). Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08usb: dfu: correct dfu buffer inited valueBo Shen
After dfu buffer is initialized, the buffer should be all available, while not 0. Initialize its value to min(dfu_buf_size, dfu->r_left). Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08usb: dfu: decrease dfu->r_left along with the transferBo Shen
The value of dfu->r_left need decrease along with the transfer Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-11-08usb: ohci-hcd: submit_common_msg: report actual_length properlyMateusz Kulikowski
submit_common_msg should report amount of data passed from/to device. Instead, it always returned size requested by Host. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2013-11-08usb: ums: add ums exit feature by ctrl+c or by detach usb cablePrzemyslaw Marczak
This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 00:43:08 +0000