summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-07-13Blackfin: bf533-stamp: scrub unused codeMike Frysinger
Much of the local bf533-stamp.h header is unused, and the few bits that are are only needed in one file. So move the few used bits out and punt all the rest. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: blackstamp: convert eth/flash swap logic to gpio frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: bf533-stamp: convert eth/flash swap logic to gpio frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: bfin_spi: support gpios as chip selectsMike Frysinger
Rather than only support the pins dedicated as chip selects, utilize the gpio framework to support any gpio pin. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: bfin_spi: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: serial: convert to portmux frameworkMike Frysinger
Use the new portmux framework to handle the details when possible. Unfortunately, we cannot yet use this in the standalone initialization logic, so we need to keep around the old portmux writes for now. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: pata_bfin: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: bfin_sdh: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13Blackfin: bfin_nand: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Scott Wood <scottwood@freescale.com>
2010-07-13Blackfin: bfin_mac: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. While we're doing this, let boards declare the exact list of pins they need in case there is one or two they don't actually have hooked up. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12edminiv2: add ethernet supportAlbert Aribaud
Add edminiv2 board support for mv_egiga. Add edminiv2 config to enable mv_egiga. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12mvgbe: add support for orion5x GbE controllerAlbert Aribaud
Add definitions and initialization in orion5x for mvgbe. Add orion5x in mvgbe SoC includes. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12mvgbe: support SoCs other than kirkwoodAlbert Aribaud
Rename all references to kirkwood in mvgbe symbols throughout the whole codebase. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12net: rename: kirkwood_egiga as mvgbeAlbert Aribaud
Rename kirkwood_egiga.* to mvgbe.* and adjust makefile and #include accordingly. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12kirkwood_egiga: CONFIG_SKIP_LOCAL_MAC_RANDOMIZATIONAlbert Aribaud
This configuration option allows SoCs without random generation capability to fill in local MACs with a fixed rather than random value Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12NAND: formatting cleanups from env.oob supportScott Wood
Change if (ok) { bunch of stuff } else { error } to if (error) { get out } proceed with bunch of stuff Plus a few whitespace cleanups. Signed-off-by: Scott Wood <scottwood@freescale.com>
2010-07-12NAND: environment offset in OOB (CONFIG_ENV_OFFSET_OOB)Ben Gardiner
This is a re-submission of the patch by Harald Welte <laforge@openmoko.org> with minor modifications for rebase and changes as suggested by Scott Wood <scottwood@freescale.com> [1] [2]. This patch enables the environment partition to have a run-time dynamic location (offset) in the NAND flash. The reason for this is simply that all NAND flashes have factory-default bad blocks, and a fixed compile time offset would mean that sometimes the environment partition would live inside factory bad blocks. Since the number of factory default blocks can be quite high (easily 1.3MBytes in current standard components), it is not economic to keep that many spare blocks inside the environment partition. With this patch and CONFIG_ENV_OFFSET_OOB enabled, the location of the environment partition is stored in the out-of-band (OOB) data of the first block in flash. Since the first block is where most systems boot from, the vendors guarantee that the first block is not a factory default block. This patch introduces the 'nand env.oob' command, which can be called from the u-boot command line. 'nand env.oob get' reads the address of the environment partition from the OOB data, 'nand env.oob set {offset,partition-name}' allows the setting of the marker by specifying a numeric offset or a partition name. [1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/43916 [2] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/79195 Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Acked-by: Harald Welte <laforge@gnumonks.org>
2010-07-12nios2: remove EP1C20, EP1S10, EP1S40 boardsThomas Chou
The example configuration files of nios2-generic board can generated binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three boards can be removed. With nios2-generic approach, the fpga parameter header file can be generated from hardware designs using tools. Porting u-boot for nios2 boards is simplified. Vendors can supply their fpga parameter file or patches to add a new nios2-generic board instance. There is no need to include other boards support for nios2 in the u-boot mainline. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12nios2: add spi flash support to nios2-generic boardThomas Chou
This patch enables the altera_spi and spi_flash drivers for the nios2-generic board. It allows access to the EPCS/SPI flash on the Altera EP1C20 board. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Tested-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12gpio_led: add gpio_request to __led_initThomas Chou
This patch adds the gpio usage request. The polarity is changed to positive as suggested by Mike Frysinger. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12nios2: add gpio_requestThomas Chou
This will be used by nand_plat. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12nios2: add fdt supportThomas Chou
This patch adds fdt support to boot linux, followed Michal's work on microblaze. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12nios2: use gc sections to reduce image sizeThomas Chou
Follow the discussion of Charles Manning and Mike Frysinger. Using gc_sections helps reduce image size. Configuring for nios2-generic board... Before, text data bss dec hex filename 123979 3724 22892 150595 24c43 /tmp/u-boot/u-boot After, text data bss dec hex filename 115983 3800 22732 142515 22cb3 /tmp/u-boot/u-boot Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12cpuat91: unbreak ethernetEric Bénard
* the following problems are met : config was set to use the new driver as a default but - RMII was not enabled for the new driver - the new driver didn't compile with RMII enabled - the new driver initialize a PHY at address O when the PHY of this board is at 1 thus we get "AT91 EMAC RMII: No PHY present" * to fix these problems, this patch : - enable RMII for the new driver - fix the wrong define used in the at91_emac.c - allow the config file to set a default phy address (and use 0 as a default as in the actual at91_emac.c driver) Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12at91_emac: Write MAC address automaticallyEric Bénard
tested on cpuat91. Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: use standard I/O accessorsMike Frysinger
The current dm9000x driver accesses its memory mapped registers directly instead of using the standard I/O accessors. This can cause problems on Blackfin systems as the accesses can get out of order. So convert the direct volatile dereferences to use the normal in/out macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: make OUTW handle 32bit/16bit defines tooHoan Hoang
The current OUTW function is always defined as a 16bit function, but this doesn't work correctly when using the 32bit access mode. So define it as a 32bit function when in 32bit mode so things work correctly on Blackfin 32bit LE systems. Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: add support for the Marvell 88E1118 phyHoan Hoang
Some places in the current code equate the Marvell 88E1111 PHY as the family when in reality it's a subpart of the Alaska family. So once we generalize that, add support for the 88E1118 PHY. Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12Write MAC address automatically on MACB-based boardsBen Warren
Also, remove all calls to eth_init() in boards that use MACB Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12smc91xx_eeprom: Correct chip detection check.Juergen Kilb
The smc911x_detect function in /net/driver/net/smc911x.c returns a 0 if everything was ok (a chip was found) and -1 else. In the standalone example 'smc911x_eeprom' the return value of smc911x_detect is interpreted in a different way (0 for error, !0 as OK). This leads to the error that the chip will not be detected. Signed-off-by: Juergen Kilb <j.kilb@phytec.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12tsec: fix the return value for tsec_eth_init()Timur Tabi
The Ethernet initialization functions are supposed to return the number of devices initialized, so fix tsec_eth_init() so that they returns the number of TSECs initialized, instead of just zero. This is safe because the return value is currently ignored by all callers, but now they don't have to ignore it. In general, if an function initializes only one device, then it should return a negative number if there's an error. If it initializes more than one device, then it should never return a negative number. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12uli526x: drop newlines from device nameMike Frysinger
Device names should not contain non-printable characters like newlines. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12net: warn about spaces in device namesMike Frysinger
Some commands operate on eth device names (like 'mii'), but those cannot be passed on the command line as one argument. So detect devices like these and warn about them so someone will fix it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: switch to common mii.h headerMike Frysinger
No compiled code change here, just drop the local PHY defines in favor of the common standard ones. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: improve phy searchingMike Frysinger
Rather than hardcode specific phy addresses, search the possible phy address space to find the first available phy. Also respect the normal CONFIG_PHY_ADDR option for board porters to pick a specific address. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: fix media typosHoan Hoang
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12AX88180: add missing init prototypeMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12kirkwood_egiga: updates: fix DRAM mapping and typoAlbert Aribaud
DRAM window mapping uses kirkwood-provided functions instead of global gd as do other drivers--fix this. Also, fix a typo in a comment Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12SPEAr : Network driver support addedVipin KUMAR
Designware network driver support added. This is a Synopsys ethernet controller Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12kirkwood_egiga: bugfix: add DMA sequence pointsAlbert Aribaud
Insert isb() sequence points to ensure DMA descriptors are filled in and set up before actual DMA occurs. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12net: Add option to disable fiber on M88E1111 PHY for PPC4xxStefan Roese
By defining CONFIG_M88E1111_DISABLE_FIBER boards can configure the M88E1111 PYH to disable fiber. This is needed for an upcoming PPC460GT based board, which has fiber/copper auto-selection enabled by default. This doesn't seem to work. So we disable fiber in the PHY register. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12net: dm9000x: re-add casts to I/O pointers to fix gcc warningsMike Frysinger
The DM9000 in/out helper functions were casting the register address when it was accessing things directly (pre commit a45dde2293c816138e53c). But when it was changed to using the in/out helpers, those casts were dropped because those functions don't take pointers. Even more recently, those functions were then changed to use the read/write helpers, but the casts were not re-added. This is necessary because the read/write helpers do take pointers. Otherwise we get a lot of warnings like: dm9000x.c: In function 'dm9000_inblk_8bit': dm9000x.c:172: warning: passing argument 1 of 'readb' makes pointer from integer without a cast Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Thomas Weber <weber@corscience.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12tsec: add micrel ksz804 phyHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-0983xx: add support for ve8313 boardHeiko Schocher
This patch add support for the ve8313 board based on Freescale MPC8313 CPU. - serial console on UART 1 - 128 MB DDR RAM - 32 MB NOR Flash - 16 MB NAND Flash - Ethernet MII Mode over on TSEC0 - micrel ksz804 phy - Hardware WDT MAX824 changes since v1 - Environment size = sector size - use red. environment - add comments from Kim Phillips - add MAKEALL, MAINTAINERS entry - Codingstyle issues fixed - inserted original Copyrights - PCI subsys vendor ID changed from 0x1057 (Motorola) to 0x1957 (Freescale) changes since v2 - add comments from Wolfgang Denk - fix Codingstyle and some comments - reworked WDT reset (just toggling the WD_TRIG pin) - Environment size now 16KiB - fixed RAMBOOT version - fixed CONFIG_SYS_LOAD_ADDR - renamed CONFIG_TSEC1_NAME to TSEC1 Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09MPC8308RDB: minimal support for devboard from FreescaleIlya Yanok
This patch provides support for MPC8308RDB development board from Freescale with a minimal set of features: Dual UART is supported NOR flash is supported Both TSEC Ethernet controllers are supported PCI Express initialization is supported The following features are enabled in configuration but not fully tested: I2C (used to get the board revision) I2C-connected RTC VSC7385 switch There is one (hopefully) minor issue: on soft reset the board sometimes resets twice. I've not managed to find the fix for this problem yet. As a workaround instruction cache can be disabled. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09mpc8308: support for Freescale MPC8308 cpuIlya Yanok
This patch adds basic support for Freescale MPC8308 CPU. Serial ports, NOR flash and integrated Ethernet controllers are supported. PCI Express is also supported. eSDHC, NAND and USB may work but aren't tested (using ULPI PHY requires additional patch). Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09SAMSUNG: serial: remove compiler warningsMinkyu Kang
remove below warnings serial_s5p.c: In function 'serial_getc_dev': serial_s5p.c:136: warning: dereferencing type-punned pointer will break strict-aliasing rules serial_s5p.c: In function 'serial_putc_dev': serial_s5p.c:152: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-07-08Blackfin: convert plat-nand code to GPIO frameworkMike Frysinger
Use the new GPIO framework code in both the Blackfin arch and the nand_plat driver to simplify things greatly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-08mtd: nand_plat: add simple GPIO framework DEV_READY optionMike Frysinger
Make it easy to use GPIOs for the DEV_READY pin by using the common GPIO framework. Also make the NAND_PLAT_INIT() define optional. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-07-08NAND: add Toshiba TC58NVG0 identifierFlorian Fainelli
The Toshiba TC58NVG0* parts are 128Mbytes x 8 bits 3.3V parts with the 0xD1 identifier. Add these to the list of known devices IDs. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-01 01:58:30 +0000